On 09/09/2022 08:46, elvis.wang wrote: > Hello Krzysztof, > > On Tue, 2022-08-02 at 10:08 +0200, Krzysztof Kozlowski wrote: >> On 29/07/2022 10:43, Elvis Wang wrote: >>> Add gce header file to define the gce subsys id, hardware event id >>> and >>> constant for mt8188. >>> >>> Signed-off-by: Elvis Wang <Elvis.Wang@xxxxxxxxxxxx> >>> --- >>> include/dt-bindings/gce/mt8188-gce.h | 1079 >>> ++++++++++++++++++++++++++ >>> 1 file changed, 1079 insertions(+) >>> create mode 100644 include/dt-bindings/gce/mt8188-gce.h >>> >>> diff --git a/include/dt-bindings/gce/mt8188-gce.h b/include/dt- >>> bindings/gce/mt8188-gce.h >>> new file mode 100644 >>> index 000000000000..b15e965fe671 >>> --- /dev/null >>> +++ b/include/dt-bindings/gce/mt8188-gce.h >> >> Use vendor in filename, so mediatek,mt8188-gce.h > > yes, mediatek,mt8188-gce.h as filename would be better, will change in > next version. > >> >>> @@ -0,0 +1,1079 @@ >>> +/* SPDX-License-Identifier: GPL-2.0 */ >> >> Dual license. > > ok, will use /* SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause */ in > next version. Also ask if it is possible to use BSD-3-CLause? Please use GPL-2.0 OR BSD-2-Clause. >> >>> + >>> +/* GCE thread priority */ >>> +#define CMDQ_THR_PRIO_LOWEST 0 >>> +#define CMDQ_THR_PRIO_1 1 >>> +#define CMDQ_THR_PRIO_2 2 >>> +#define CMDQ_THR_PRIO_3 3 >>> +#define CMDQ_THR_PRIO_4 4 >>> +#define CMDQ_THR_PRIO_5 5 >>> +#define CMDQ_THR_PRIO_6 6 >>> +#define CMDQ_THR_PRIO_HIGHEST 7 >>> + >>> +/* CPR count in 32bit register */ >>> +#define GCE_CPR_COUNT 1312 >> >> No register values in the bindings. > > Those thread priority will be referenced in the device node and > congfigured to the hw when trigger hw work. Using something in DTS does not mean you have to encode it in bindings. Bindings describe the DTS, not the hardware programming model. > >> >> >> >>> + >>> +/* GCE subsys table */ >>> +#define SUBSYS_1400XXXX 0 >>> +#define SUBSYS_1401XXXX 1 >>> +#define SUBSYS_1402XXXX 2 >>> +#define SUBSYS_1c00XXXX 3 >>> +#define SUBSYS_1c01XXXX 4 >>> +#define SUBSYS_1c02XXXX 5 >>> +#define SUBSYS_1c10XXXX 6 >>> +#define SUBSYS_1c11XXXX 7 >>> +#define SUBSYS_1c12XXXX 8 >>> +#define SUBSYS_14f0XXXX 9 >>> +#define SUBSYS_14f1XXXX 10 >>> +#define SUBSYS_14f2XXXX 11 >>> +#define SUBSYS_1800XXXX 12 >>> +#define SUBSYS_1801XXXX 13 >>> +#define SUBSYS_1802XXXX 14 >>> +#define SUBSYS_1803XXXX 15 >>> +#define SUBSYS_1032XXXX 16 >>> +#define SUBSYS_1033XXXX 17 >>> +#define SUBSYS_1600XXXX 18 >>> +#define SUBSYS_1601XXXX 19 >>> +#define SUBSYS_14e0XXXX 20 >>> +#define SUBSYS_1c20XXXX 21 >>> +#define SUBSYS_1c30XXXX 22 >>> +#define SUBSYS_1c40XXXX 23 >>> +#define SUBSYS_1c50XXXX 24 >>> +#define SUBSYS_1c60XXXX 25 >>> +#define SUBSYS_NO_SUPPORT 99 >>> + >>> +/* GCE General Purpose Register (GPR) support >>> + * Leave note for scenario usage here >>> + */ >>> +/* GCE: write mask */ >>> +#define GCE_GPR_R00 0x00 >>> +#define GCE_GPR_R01 0x01 >> >> No. These are no bindings. Do not embed device programming model into >> bindings header. I'll stop review. > > This GCE_GPR define is an attribute of hw, and different hw versions > may have different gpr number. It does not matter that different devices have different programming model. The bindings are not a place for it. Best regards, Krzysztof
