Re: [PATCH v2 12/13] tty: serial: atmel: Make the driver aware of the existence of GCLK

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 07.09.2022 12:36, Ilpo Järvinen wrote:
> On Tue, 6 Sep 2022, Sergiu Moga wrote:
> 
>> Previously, the atmel serial driver did not take into account the
>> possibility of using the more customizable generic clock as its
>> baudrate generator. Unless there is a Fractional Part available to
>> increase accuracy, there is a high chance that we may be able to
>> generate a baudrate closer to the desired one by using the GCLK as the
>> clock source. Now, depending on the error rate between
>> the desired baudrate and the actual baudrate, the serial driver will
>> fallback on the generic clock. The generic clock must be provided
>> in the DT node of the serial that may need a more flexible clock source.
>>
>> Signed-off-by: Sergiu Moga <sergiu.moga@xxxxxxxxxxxxx>
>> ---
>>
>>
>>
>> v1 -> v2:
>> - take into account the different placement of the baudrate clock source
>> into the IP's Mode Register (USART vs UART)
>> - don't check for atmel_port->gclk != NULL
>> - use clk_round_rate instead of clk_set_rate + clk_get_rate
>> - remove clk_disable_unprepare from the end of the probe method
>>
>>
>>
>>   drivers/tty/serial/atmel_serial.c | 52 ++++++++++++++++++++++++++++++-
>>   1 file changed, 51 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
>> index 6aa01ca5489c..b2b6fd6ea2a5 100644
>> --- a/drivers/tty/serial/atmel_serial.c
>> +++ b/drivers/tty/serial/atmel_serial.c
>> @@ -15,6 +15,7 @@
>>   #include <linux/init.h>
>>   #include <linux/serial.h>
>>   #include <linux/clk.h>
>> +#include <linux/clk-provider.h>
>>   #include <linux/console.h>
>>   #include <linux/sysrq.h>
>>   #include <linux/tty_flip.h>
>> @@ -77,6 +78,8 @@ static void atmel_stop_rx(struct uart_port *port);
>>   #endif
>>
>>   #define ATMEL_ISR_PASS_LIMIT 256
>> +#define ERROR_RATE(desired_value, actual_value) \
>> +     ((int)(100 - ((desired_value) * 100) / (actual_value)))
> 
> Make a function instead.
> 


Alright, I see the point of making it an inline function instead.


> Is percent accurate enough or would you perhaps want something slightly
> more accurate?
> 


It is accurate enough for the all the baudrates I have tested. It 
usually taps into the GCLK whenever high baudrates such as 921600 are 
used. For 115200 for example, the error rate was slightly better in the 
case of the peripheral clock and it acted accordingly, choosing the 
latter as its baudrate source clock. I do not think that a higher 
accuracy than this would be needed though. Say that using percent 
accuracy yields that the error rates are equal, but the gclk would have 
been better in this case by, say, a few 10 ^ -4, but the code logic does 
not see it so it proceeds using the peripheral clock. In that case, the 
error rate of the peripheral clock would still be low enough relative to 
the desired baudrate for the communication to function properly.

The higher the baudrate, the lower the error rate must be in order for 
things to go smoothly. For example, for a baudrate of 57600 I noticed 
that even an error rate as big as 6% is still enough for the 
communication to work properly, while in the case of 921600 anything 
bigger than 2% and things do not go smoothly anymore. So I guess that it 
would be safe to say that, unless you go for baudrates as high as tens 
of millions, things should work well with just percent accuracy. A 
higher accuracy always definetely helps, but I believe it is not needed 
in this case.


> Given you've abs() at the caller side, the error rate could be
> underestimated, is underestimating OK?
> 


Yes, this should be fine. While (both empirically and after looking 
stuff up) I noticed that in the case of negative error rates, their 
absolute value needs to be smaller than the one of positive error rates, 
it must be so by a very small margin that is negligible when estimating 
through percent accuracy.


> --
>   i.
> 
>>   struct atmel_dma_buffer {
>>        unsigned char   *buf;
>> @@ -110,6 +113,7 @@ struct atmel_uart_char {
>>   struct atmel_uart_port {
>>        struct uart_port        uart;           /* uart */
>>        struct clk              *clk;           /* uart clock */
>> +     struct clk              *gclk;          /* uart generic clock */
>>        int                     may_wakeup;     /* cached value of device_may_wakeup for times we need to disable it */
>>        u32                     backup_imr;     /* IMR saved during suspend */
>>        int                     break_active;   /* break being received */
>> @@ -2117,6 +2121,8 @@ static void atmel_serial_pm(struct uart_port *port, unsigned int state,
>>                 * This is called on uart_close() or a suspend event.
>>                 */
>>                clk_disable_unprepare(atmel_port->clk);
>> +             if (__clk_is_enabled(atmel_port->gclk))
>> +                     clk_disable_unprepare(atmel_port->gclk);
>>                break;
>>        default:
>>                dev_err(port->dev, "atmel_serial: unknown pm %d\n", state);
>> @@ -2131,7 +2137,8 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
>>   {
>>        struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>>        unsigned long flags;
>> -     unsigned int old_mode, mode, imr, quot, baud, div, cd, fp = 0;
>> +     unsigned int old_mode, mode, imr, quot, div, cd, fp = 0;
>> +     unsigned int baud, actual_baud, gclk_rate;
>>
>>        /* save the current mode register */
>>        mode = old_mode = atmel_uart_readl(port, ATMEL_US_MR);
>> @@ -2297,6 +2304,43 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
>>                cd &= 65535;
>>        }
>>
>> +     /*
>> +      * If there is no Fractional Part, there is a high chance that
>> +      * we may be able to generate a baudrate closer to the desired one
>> +      * if we use the GCLK as the clock source driving the baudrate
>> +      * generator.
>> +      */
>> +     if (!atmel_port->has_frac_baudrate) {
>> +             if (__clk_is_enabled(atmel_port->gclk))
>> +                     clk_disable_unprepare(atmel_port->gclk);
>> +             gclk_rate = clk_round_rate(atmel_port->gclk, 16 * baud);
>> +             actual_baud = clk_get_rate(atmel_port->clk) / (16 * cd);
>> +             if (gclk_rate && abs(ERROR_RATE(baud, actual_baud)) >
>> +                 abs(ERROR_RATE(baud, gclk_rate / 16))) {
>> +                     clk_set_rate(atmel_port->gclk, 16 * baud);
>> +                     if (!clk_prepare_enable(atmel_port->gclk)) {
>> +                             if (atmel_port->is_usart) {
>> +                                     mode &= ~ATMEL_US_USCLKS;
>> +                                     mode |= ATMEL_US_USCLKS_GCLK;
>> +                             } else {
>> +                                     mode &= ~ATMEL_UA_BRSRCCK;
>> +                                     mode |= ATMEL_UA_BRSRCCK_GCLK;
>> +                             }
>> +
>> +                             /*
>> +                              * Set the Clock Divisor for GCLK to 1.
>> +                              * Since we were able to generate the smallest
>> +                              * multiple of the desired baudrate times 16,
>> +                              * then we surely can generate a bigger multiple
>> +                              * with the exact error rate for an equally increased
>> +                              * CD. Thus no need to take into account
>> +                              * a higher value for CD.
>> +                              */
>> +                             cd = 1;
>> +                     }
>> +             }
>> +     }
>> +
>>        quot = cd | fp << ATMEL_US_FP_OFFSET;
>>
>>        if (!(port->iso7816.flags & SER_ISO7816_ENABLED))
>> @@ -2892,6 +2936,12 @@ static int atmel_serial_probe(struct platform_device *pdev)
>>        if (ret)
>>                goto err;
>>
>> +     atmel_port->gclk = devm_clk_get_optional(&pdev->dev, "gclk");
>> +     if (IS_ERR(atmel_port->gclk)) {
>> +             ret = PTR_ERR(atmel_port->gclk);
>> +             goto err;
>> +     }
>> +
>>        ret = atmel_init_port(atmel_port, pdev);
>>        if (ret)
>>                goto err_clk_disable_unprepare;
>>





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux