Hi Tom, thanks for getting the upstreaming of this DT going. Some comments below. On Mon, Aug 15, 2022 at 10:30:04PM +1000, Tom Fitzhenry wrote: > From: Martijn Braam <martijn@xxxxxxxxx> > > This is a basic DT containing regulators and UART, intended to be a > base that myself and others can add additional nodes in future patches. > > Tested to work: booting from eMMC, output over UART. You're also adding the SD controller here. Does it work as is? If so add it to the commit description as well. > [..] > --- /dev/null > +++ b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts > @@ -0,0 +1,394 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (c) 2020 Martijn Braam <martijn@xxxxxxxxx> > + * Copyright (c) 2021 Kamil Trzciński <ayufan@xxxxxxxxx> > + */ > + > +/* PinePhone Pro datasheet: First comment line should be empty following the coding style [1]. Like you did for the copyrights above. [1] https://www.kernel.org/doc/html/latest/process/coding-style.html#commenting > + * https://files.pine64.org/doc/PinePhonePro/PinephonePro-Schematic-V1.0-20211127.pdf > + */ [..] > + vcc_sysin: vcc-sysin-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vcc_sysin"; This signal is called vcc_sys in the datasheet, so I suggest we keep that name here. It's not everyday that we get a device with a publicly available datasheet :^). > + regulator-always-on; > + regulator-boot-on; > + }; [..] > + rk818: pmic@1c { > + compatible = "rockchip,rk818"; > + reg = <0x1c>; > + interrupt-parent = <&gpio1>; > + interrupts = <RK_PC5 IRQ_TYPE_LEVEL_LOW>; > + #clock-cells = <1>; > + clock-output-names = "xin32k", "rk808-clkout2"; What about keeping the datasheet names here too? clk32kout1, clk32kout2 > + pinctrl-names = "default"; [..] > + vcc_1v8: vcc_wl: DCDC_REG4 { >From the datasheet, vcc_wl is actually wired to vcc3v3_sys. But looks like vcc_wl is only used for bluetooth and you're not enabling it yet anyway, so just drop this extra label, and it can be added when bluetooth is added (or not, and then the bluetooth supply just points directly to vcc3v3_sys). > + regulator-name = "vcc_1v8"; [..] > + vcc_power_on: LDO_REG4 { > + regulator-name = "vcc_power_on"; The name on the datasheet for this one is rk818_pwr_on. > + regulator-always-on; [..] > +&cluster0_opp { > + opp04 { > + status = "disabled"; > + }; > + > + opp05 { > + status = "disabled"; > + }; > +}; I saw the discussion on the previous version about using the rk3399-opp.dtsi here, but the thing is, this OPP has greater values for the max voltage than the maximum allowed on the OPP table you posted previously (for RK3399-T)... Same thing for the GPU OPP. > + > +&cluster1_opp { > + opp06 { > + status = "disabled"; > + }; There's actually an opp06 node in the OPP for RK3399-T, only that the frequency is slightly lower. Maybe you could keep it enabled but override the frequency? Or given the above point about the max voltages, maybe it would be best to have a separate OPP table after all? > + > + opp07 { > + status = "disabled"; > + }; > +}; > + > +&io_domains { > + status = "okay"; Let's keep the status at the end of the node for consistency with the rest. With these points addressed: Reviewed-by: Nícolas F. R. A. Prado <n@xxxxxxxxxxxxx> I'll also try to give this a test shortly. Thanks, Nícolas > + > + bt656-supply = <&vcc1v8_dvp>; > + audio-supply = <&vcca1v8_codec>; > + sdmmc-supply = <&vccio_sd>; > + gpio1830-supply = <&vcc_3v0>; > +}; [..]
