[PATCH v3 3/3] arm64: dts: renesas: rzg2l-smarc-som: Add PHY interrupt support for ETH{0/1}

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The PHY interrupt (INT_N) pin is connected to IRQ2 and IRQ3 for ETH0
and ETH1 respectively.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
---
v2->v3
* Included irqc-rzg2l.h header

v1->v2
* Used macros of IRQ numbers
---
 arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
index 9410796c8ad6..c4faff092380 100644
--- a/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
@@ -6,6 +6,7 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irqc-rzg2l.h>
 #include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
 
 /* SW1[2] should be at position 2/OFF to enable 64 GB eMMC */
@@ -94,6 +95,8 @@ phy0: ethernet-phy@7 {
 		compatible = "ethernet-phy-id0022.1640",
 			     "ethernet-phy-ieee802.3-c22";
 		reg = <7>;
+		interrupt-parent = <&irqc>;
+		interrupts = <RZG2L_IRQ2 IRQ_TYPE_LEVEL_LOW>;
 		rxc-skew-psec = <2400>;
 		txc-skew-psec = <2400>;
 		rxdv-skew-psec = <0>;
@@ -120,6 +123,8 @@ phy1: ethernet-phy@7 {
 		compatible = "ethernet-phy-id0022.1640",
 			     "ethernet-phy-ieee802.3-c22";
 		reg = <7>;
+		interrupt-parent = <&irqc>;
+		interrupts = <RZG2L_IRQ3 IRQ_TYPE_LEVEL_LOW>;
 		rxc-skew-psec = <2400>;
 		txc-skew-psec = <2400>;
 		rxdv-skew-psec = <0>;
@@ -171,7 +176,8 @@ eth0_pins: eth0 {
 			 <RZG2L_PORT_PINMUX(25, 0, 1)>, /* ET0_RXD0 */
 			 <RZG2L_PORT_PINMUX(25, 1, 1)>, /* ET0_RXD1 */
 			 <RZG2L_PORT_PINMUX(26, 0, 1)>, /* ET0_RXD2 */
-			 <RZG2L_PORT_PINMUX(26, 1, 1)>; /* ET0_RXD3 */
+			 <RZG2L_PORT_PINMUX(26, 1, 1)>, /* ET0_RXD3 */
+			 <RZG2L_PORT_PINMUX(1, 0, 1)>;  /* IRQ2 */
 	};
 
 	eth1_pins: eth1 {
@@ -189,7 +195,8 @@ eth1_pins: eth1 {
 			 <RZG2L_PORT_PINMUX(34, 1, 1)>, /* ET1_RXD0 */
 			 <RZG2L_PORT_PINMUX(35, 0, 1)>, /* ET1_RXD1 */
 			 <RZG2L_PORT_PINMUX(35, 1, 1)>, /* ET1_RXD2 */
-			 <RZG2L_PORT_PINMUX(36, 0, 1)>; /* ET1_RXD3 */
+			 <RZG2L_PORT_PINMUX(36, 0, 1)>, /* ET1_RXD3 */
+			 <RZG2L_PORT_PINMUX(1, 1, 1)>;  /* IRQ3 */
 	};
 
 	gpio-sd0-pwr-en-hog {
-- 
2.25.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux