[Your To: header field has:
To: unlisted-recipients:; (no To-header on input)
which is added to the receiver list when replying to all in Mozilla
Thunderbird 91.10.0.
]
Dear Hakan,
Am 20.06.22 um 14:01 schrieb Hakan Jansson:
Add device specific data for max baudrate in autobaud mode. This allows the
host to use a baudrate higher than "init speed" when loading FW in autobaud
mode.
Please mention 921600 in the commit message, and maybe also document
what the current default is.
Please also add the measurement data to the commit message, that means,
how much is the time to load the firmware decreased.
Signed-off-by: Hakan Jansson <hakan.jansson@xxxxxxxxxxxx>
---
drivers/bluetooth/hci_bcm.c | 20 ++++++++++++++++----
1 file changed, 16 insertions(+), 4 deletions(-)
diff --git a/drivers/bluetooth/hci_bcm.c b/drivers/bluetooth/hci_bcm.c
index 0ae627c293c5..d7e0b75db8a6 100644
--- a/drivers/bluetooth/hci_bcm.c
+++ b/drivers/bluetooth/hci_bcm.c
@@ -53,10 +53,12 @@
* struct bcm_device_data - device specific data
* @no_early_set_baudrate: Disallow set baudrate before driver setup()
* @drive_rts_on_open: drive RTS signal on ->open() when platform requires it
+ * @max_autobaud_speed: max baudrate supported by device in autobaud mode
*/
struct bcm_device_data {
bool no_early_set_baudrate;
bool drive_rts_on_open;
+ u32 max_autobaud_speed;
Why specify the length, and not just `unsigned int`? Maybe also add the
unit to the variable name?
};
/**
@@ -100,6 +102,7 @@ struct bcm_device_data {
* @drive_rts_on_open: drive RTS signal on ->open() when platform requires it
* @pcm_int_params: keep the initial PCM configuration
* @use_autobaud_mode: start Bluetooth device in autobaud mode
+ * @max_autobaud_speed: max baudrate supported by device in autobaud mode
*/
struct bcm_device {
/* Must be the first member, hci_serdev.c expects this. */
@@ -139,6 +142,7 @@ struct bcm_device {
bool drive_rts_on_open;
bool use_autobaud_mode;
u8 pcm_int_params[5];
+ u32 max_autobaud_speed;
Ditto.
};
/* generic bcm uart resources */
@@ -479,7 +483,10 @@ static int bcm_open(struct hci_uart *hu)
else if (bcm->dev->drive_rts_on_open)
hci_uart_set_flow_control(hu, true);
- hu->init_speed = bcm->dev->init_speed;
+ if (bcm->dev->use_autobaud_mode && bcm->dev->max_autobaud_speed)
+ hu->init_speed = min(bcm->dev->oper_speed, bcm->dev->max_autobaud_speed);
+ else
+ hu->init_speed = bcm->dev->init_speed;
/* If oper_speed is set, ldisc/serdev will set the baudrate
* before calling setup()
@@ -585,8 +592,8 @@ static int bcm_setup(struct hci_uart *hu)
return 0;
/* Init speed if any */
- if (hu->init_speed)
- speed = hu->init_speed;
+ if (bcm->dev && bcm->dev->init_speed)
+ speed = bcm->dev->init_speed;
else if (hu->proto->init_speed)
speed = hu->proto->init_speed;
else
@@ -1519,6 +1526,7 @@ static int bcm_serdev_probe(struct serdev_device *serdev)
data = device_get_match_data(bcmdev->dev);
if (data) {
+ bcmdev->max_autobaud_speed = data->max_autobaud_speed;
bcmdev->no_early_set_baudrate = data->no_early_set_baudrate;
bcmdev->drive_rts_on_open = data->drive_rts_on_open;
}
@@ -1542,6 +1550,10 @@ static struct bcm_device_data bcm43438_device_data = {
.drive_rts_on_open = true,
};
+static struct bcm_device_data cyw55572_device_data = {
+ .max_autobaud_speed = 921600,
+};
+
static const struct of_device_id bcm_bluetooth_of_match[] = {
{ .compatible = "brcm,bcm20702a1" },
{ .compatible = "brcm,bcm4329-bt" },
@@ -1554,7 +1566,7 @@ static const struct of_device_id bcm_bluetooth_of_match[] = {
{ .compatible = "brcm,bcm4349-bt", .data = &bcm43438_device_data },
{ .compatible = "brcm,bcm43540-bt", .data = &bcm4354_device_data },
{ .compatible = "brcm,bcm4335a0" },
- { .compatible = "infineon,cyw55572-bt" },
+ { .compatible = "infineon,cyw55572-bt", .data = &cyw55572_device_data },
{ },
};
MODULE_DEVICE_TABLE(of, bcm_bluetooth_of_match);
Kind regards,
Paul
