On Tuesday 24 May 2022 11:23:32 Pali Rohár wrote: > On Wednesday 11 May 2022 16:37:12 Pali Rohár wrote: > > CZ.NIC Turris 1.0 and 1.1 are open source routers, they have dual-core > > PowerPC Freescale P2020 CPU and are based on Freescale P2020RDB-PC-A board. > > Hardware design is fully open source, all firmware and hardware design > > files are available at Turris project website: > > > > https://docs.turris.cz/hw/turris-1x/turris-1x/ > > https://project.turris.cz/en/hardware.html > > > > Signed-off-by: Pali Rohár <pali@xxxxxxxxxx> > > --- > > arch/powerpc/boot/dts/turris1x.dts | 470 +++++++++++++++++++++++++++++ > > 1 file changed, 470 insertions(+) > > create mode 100644 arch/powerpc/boot/dts/turris1x.dts > > Michael, Rob: PING? PING? > > diff --git a/arch/powerpc/boot/dts/turris1x.dts b/arch/powerpc/boot/dts/turris1x.dts > > new file mode 100644 > > index 000000000000..2a624f117586 > > --- /dev/null > > +++ b/arch/powerpc/boot/dts/turris1x.dts > > @@ -0,0 +1,470 @@ > > +// SPDX-License-Identifier: GPL-2.0+ > > +/* > > + * Turris 1.x Device Tree Source > > + * > > + * Copyright 2013 - 2022 CZ.NIC z.s.p.o. (http://www.nic.cz/) > > + * > > + * Pinout, Schematics and Altium hardware design files are open source > > + * and available at: https://docs.turris.cz/hw/turris-1x/turris-1x/ > > + */ > > + > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/interrupt-controller/irq.h> > > +#include <dt-bindings/leds/common.h> > > +/include/ "fsl/p2020si-pre.dtsi" > > + > > +/ { > > + model = "Turris 1.x"; > > + compatible = "cznic,turris1x", "fsl,P2020RDB-PC"; /* fsl,P2020RDB-PC is required for booting Linux */ > > + > > + aliases { > > + ethernet0 = &enet0; > > + ethernet1 = &enet1; > > + ethernet2 = &enet2; > > + serial0 = &serial0; > > + serial1 = &serial1; > > + pci0 = &pci0; > > + pci1 = &pci1; > > + pci2 = &pci2; > > + spi0 = &spi0; > > + }; > > + > > + memory { > > + device_type = "memory"; > > + }; > > + > > + soc: soc@ffe00000 { > > + ranges = <0x0 0x0 0xffe00000 0x00100000>; > > + > > + i2c@3000 { > > + /* PCA9557PW GPIO controller for boot config */ > > + gpio-controller@18 { > > + compatible = "nxp,pca9557"; > > + label = "bootcfg"; > > + reg = <0x18>; > > + #gpio-cells = <2>; > > + gpio-controller; > > + polarity = <0x00>; > > + }; > > + > > + /* STM32F030R8T6 MCU for power control */ > > + power-control@32 { > > + /* > > + * Turris Power Control firmware runs on STM32F0 MCU. > > + * This firmware is open source and available at: > > + * https://gitlab.nic.cz/turris/hw/turris_power_control > > + */ > > + reg = <0x32>; > > + }; > > + > > + /* SA56004ED temperature control */ > > + temperature-sensor@4c { > > + compatible = "nxp,sa56004"; > > + reg = <0x4c>; > > + interrupt-parent = <&gpio>; > > + interrupts = <12 IRQ_TYPE_LEVEL_LOW>, /* GPIO12 - ALERT pin */ > > + <13 IRQ_TYPE_LEVEL_LOW>; /* GPIO13 - CRIT pin */ > > + }; > > + > > + /* DDR3 SPD/EEPROM */ > > + eeprom@52 { > > + compatible = "atmel,spd"; > > + reg = <0x52>; > > + }; > > + > > + /* ATSHA204-TH-DA-T crypto module */ > > + crypto@64 { > > + compatible = "atmel,atsha204"; > > + reg = <0x64>; > > + }; > > + > > + /* IDT6V49205BNLGI clock generator */ > > + clock-generator@69 { > > + compatible = "idt,6v49205b"; > > + reg = <0x69>; > > + }; > > + > > + /* MCP79402-I/ST Protected EEPROM */ > > + eeprom@57 { > > + reg = <0x57>; > > + }; > > + > > + /* MCP79402-I/ST RTC */ > > + rtc@6f { > > + compatible = "microchip,mcp7940x"; > > + reg = <0x6f>; > > + interrupt-parent = <&gpio>; > > + interrupts = <14 0>; /* GPIO14 - MFP pin */ > > + }; > > + }; > > + > > + /* SPI on connector P1 */ > > + spi0: spi@7000 { > > + }; > > + > > + gpio: gpio-controller@fc00 { > > + #interrupt-cells = <2>; > > + interrupt-controller; > > + }; > > + > > + /* Connected to SMSC USB2412-DZK 2-Port USB 2.0 Hub Controller */ > > + usb@22000 { > > + phy_type = "ulpi"; > > + dr_mode = "host"; > > + }; > > + > > + enet0: ethernet@24000 { > > + /* Connected to port 6 of QCA8337N-AL3C switch */ > > + phy-connection-type = "rgmii-id"; > > + > > + fixed-link { > > + speed = <1000>; > > + full-duplex; > > + }; > > + }; > > + > > + mdio@24520 { > > + /* QCA8337N-AL3C switch with integrated ethernet PHYs for LAN ports */ > > + switch@10 { > > + compatible = "qca,qca8337"; > > + interrupts = <2 1 0 0>; > > + reg = <0x10>; > > + > > + ports { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + port@0 { > > + reg = <0>; > > + label = "cpu1"; > > + ethernet = <&enet1>; > > + phy-mode = "rgmii-id"; > > + > > + fixed-link { > > + speed = <1000>; > > + full-duplex; > > + }; > > + }; > > + > > + port@1 { > > + reg = <1>; > > + label = "lan5"; > > + }; > > + > > + port@2 { > > + reg = <2>; > > + label = "lan4"; > > + }; > > + > > + port@3 { > > + reg = <3>; > > + label = "lan3"; > > + }; > > + > > + port@4 { > > + reg = <4>; > > + label = "lan2"; > > + }; > > + > > + port@5 { > > + reg = <5>; > > + label = "lan1"; > > + }; > > + > > + port@6 { > > + reg = <6>; > > + label = "cpu0"; > > + ethernet = <&enet0>; > > + phy-mode = "rgmii-id"; > > + > > + fixed-link { > > + speed = <1000>; > > + full-duplex; > > + }; > > + }; > > + }; > > + }; > > + > > + /* KSZ9031RNXCA ethernet phy for WAN port */ > > + phy: ethernet-phy@7 { > > + interrupts = <3 1 0 0>; > > + reg = <0x7>; > > + }; > > + }; > > + > > + ptp_clock@24e00 { > > + fsl,tclk-period = <5>; > > + fsl,tmr-prsc = <200>; > > + fsl,tmr-add = <0xcccccccd>; > > + fsl,tmr-fiper1 = <0x3b9ac9fb>; > > + fsl,tmr-fiper2 = <0x0001869b>; > > + fsl,max-adj = <249999999>; > > + }; > > + > > + enet1: ethernet@25000 { > > + /* Connected to port 0 of QCA8337N-AL3C switch */ > > + phy-connection-type = "rgmii-id"; > > + > > + fixed-link { > > + speed = <1000>; > > + full-duplex; > > + }; > > + }; > > + > > + mdio@25520 { > > + status = "disabled"; > > + }; > > + > > + enet2: ethernet@26000 { > > + /* Connected to KSZ9031RNXCA ethernet phy (WAN port) */ > > + label = "wan"; > > + phy-handle = <&phy>; > > + phy-connection-type = "rgmii-id"; > > + }; > > + > > + mdio@26520 { > > + status = "disabled"; > > + }; > > + > > + sdhc@2e000 { > > + bus-width = <4>; > > + cd-gpios = <&gpio 8 GPIO_ACTIVE_LOW>; > > + }; > > + }; > > + > > + lbc: localbus@ffe05000 { > > + reg = <0 0xffe05000 0 0x1000>; > > + > > + ranges = <0x0 0x0 0x0 0xef000000 0x01000000>, /* NOR */ > > + <0x1 0x0 0x0 0xff800000 0x00040000>, /* NAND */ > > + <0x3 0x0 0x0 0xffa00000 0x00020000>; /* CPLD */ > > + > > + /* S29GL128P90TFIR10 NOR */ > > + nor@0,0 { > > + compatible = "cfi-flash"; > > + reg = <0x0 0x0 0x01000000>; > > + bank-width = <2>; > > + device-width = <1>; > > + > > + partitions { > > + compatible = "fixed-partitions"; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + partition@0 { > > + /* 128 kB for Device Tree Blob */ > > + reg = <0x00000000 0x00020000>; > > + label = "dtb"; > > + }; > > + > > + partition@20000 { > > + /* 1.7 MB for Rescue Linux Kernel Image */ > > + reg = <0x00020000 0x001a0000>; > > + label = "rescue-kernel"; > > + }; > > + > > + partition@1c0000 { > > + /* 1.5 MB for Rescue JFFS2 Root File System */ > > + reg = <0x001c0000 0x00180000>; > > + label = "rescue-rootfs"; > > + }; > > + > > + partition@340000 { > > + /* 11 MB for TAR.XZ Backup with content of NAND Root File System */ > > + reg = <0x00340000 0x00b00000>; > > + label = "backup-rootfs"; > > + }; > > + > > + partition@e40000 { > > + /* 768 kB for Certificates JFFS2 File System */ > > + reg = <0x00e40000 0x000c0000>; > > + label = "certificates"; > > + }; > > + > > + /* free unused space 0x00f00000-0x00f20000 */ > > + > > + partition@f20000 { > > + /* 128 kB for U-Boot Environment Variables */ > > + reg = <0x00f20000 0x00020000>; > > + label = "u-boot-env"; > > + }; > > + > > + partition@f40000 { > > + /* 768 kB for U-Boot Bootloader Image */ > > + reg = <0x00f40000 0x000c0000>; > > + label = "u-boot"; > > + }; > > + }; > > + }; > > + > > + /* MT29F2G08ABAEAWP:E NAND */ > > + nand@1,0 { > > + compatible = "fsl,p2020-fcm-nand", "fsl,elbc-fcm-nand"; > > + reg = <0x1 0x0 0x00040000>; > > + nand-ecc-mode = "soft"; > > + nand-ecc-algo = "bch"; > > + > > + partitions { > > + compatible = "fixed-partitions"; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + partition@0 { > > + /* 256 MB for UBI with one volume: UBIFS Root File System */ > > + reg = <0x00000000 0x10000000>; > > + label = "rootfs"; > > + }; > > + }; > > + }; > > + > > + /* LCMXO1200C-3FTN256C FPGA */ > > + cpld@3,0 { > > + /* > > + * Turris CPLD firmware which runs on this Lattice FPGA, > > + * is extended version of P1021RDB-PC CPLD v4.1 firmware. > > + * It is backward compatible with its original version > > + * and the only extension is support for Turris LEDs. > > + * Turris CPLD firmware is open source and available at: > > + * https://gitlab.nic.cz/turris/hw/turris_cpld/-/blob/master/CZ_NIC_Router_CPLD.v > > + */ > > + compatible = "cznic,turris1x-cpld", "fsl,p1021rdb-pc-cpld", "simple-bus"; > > + reg = <0x3 0x0 0x30>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges = <0x0 0x3 0x0 0x00020000>; > > + > > + /* MAX6370KA+T watchdog */ > > + watchdog@2 { > > + /* > > + * CPLD firmware maps SET0, SET1 and SET2 > > + * input logic of MAX6370KA+T chip to CPLD > > + * memory space at byte offset 0x2. WDI > > + * input logic is outside of the CPLD and > > + * connected via external GPIO. > > + */ > > + compatible = "maxim,max6370"; > > + reg = <0x02 0x01>; > > + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; > > + }; > > + > > + led-controller@13 { > > + /* > > + * LEDs are controlled by CPLD firmware. > > + * All five LAN LEDs share common RGB settings > > + * and so it is not possible to set different > > + * colors on different LAN ports. > > + */ > > + compatible = "cznic,turris1x-leds"; > > + reg = <0x13 0x1d>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + multi-led@0 { > > + reg = <0x0>; > > + color = <LED_COLOR_ID_RGB>; > > + function = LED_FUNCTION_WAN; > > + }; > > + > > + multi-led@1 { > > + reg = <0x1>; > > + color = <LED_COLOR_ID_RGB>; > > + function = LED_FUNCTION_LAN; > > + function-enumerator = <5>; > > + }; > > + > > + multi-led@2 { > > + reg = <0x2>; > > + color = <LED_COLOR_ID_RGB>; > > + function = LED_FUNCTION_LAN; > > + function-enumerator = <4>; > > + }; > > + > > + multi-led@3 { > > + reg = <0x3>; > > + color = <LED_COLOR_ID_RGB>; > > + function = LED_FUNCTION_LAN; > > + function-enumerator = <3>; > > + }; > > + > > + multi-led@4 { > > + reg = <0x4>; > > + color = <LED_COLOR_ID_RGB>; > > + function = LED_FUNCTION_LAN; > > + function-enumerator = <2>; > > + }; > > + > > + multi-led@5 { > > + reg = <0x5>; > > + color = <LED_COLOR_ID_RGB>; > > + function = LED_FUNCTION_LAN; > > + function-enumerator = <1>; > > + }; > > + > > + multi-led@6 { > > + reg = <0x6>; > > + color = <LED_COLOR_ID_RGB>; > > + function = LED_FUNCTION_WLAN; > > + }; > > + > > + multi-led@7 { > > + reg = <0x7>; > > + color = <LED_COLOR_ID_RGB>; > > + function = LED_FUNCTION_POWER; > > + }; > > + }; > > + }; > > + }; > > + > > + pci2: pcie@ffe08000 { > > + /* > > + * PCIe bus for on-board TUSB7340RKM USB 3.0 xHCI controller. > > + * This xHCI controller is available only on Turris 1.1 boards. > > + * Turris 1.0 boards have nothing connected to this PCIe bus, > > + * so system would see only PCIe Root Port of this PCIe Root > > + * Complex. TUSB7340RKM xHCI controller has four SuperSpeed > > + * channels. Channel 0 is connected to the front USB 3.0 port, > > + * channel 1 (but only USB 2.0 subset) to USB 2.0 pins on mPCIe > > + * slot 1 (CN5), channels 2 and 3 to connector P600. > > + * > > + * P2020 PCIe Root Port uses 1MB of PCIe MEM and xHCI controller > > + * uses 64kB + 8kB of PCIe MEM. No PCIe IO is used or required. > > + * So allocate 2MB of PCIe MEM for this PCIe bus. > > + */ > > + reg = <0 0xffe08000 0 0x1000>; > > + ranges = <0x02000000 0x0 0xc0000000 0 0xc0000000 0x0 0x00200000>, /* MEM */ > > + <0x01000000 0x0 0x00000000 0 0xffc20000 0x0 0x00010000>; /* IO */ > > + > > + pcie@0 { > > + ranges; > > + }; > > + }; > > + > > + pci1: pcie@ffe09000 { > > + /* PCIe bus on mPCIe slot 2 (CN6) for expansion mPCIe card */ > > + reg = <0 0xffe09000 0 0x1000>; > > + ranges = <0x02000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000>, /* MEM */ > > + <0x01000000 0x0 0x00000000 0 0xffc10000 0x0 0x00010000>; /* IO */ > > + > > + pcie@0 { > > + ranges; > > + }; > > + }; > > + > > + pci0: pcie@ffe0a000 { > > + /* > > + * PCIe bus on mPCIe slot 1 (CN5) for expansion mPCIe card. > > + * Turris 1.1 boards have in this mPCIe slot additional USB 2.0 > > + * pins via channel 1 of TUSB7340RKM xHCI controller and also > > + * additional SIM card slot, both for USB-based WWAN cards. > > + */ > > + reg = <0 0xffe0a000 0 0x1000>; > > + ranges = <0x02000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000>, /* MEM */ > > + <0x01000000 0x0 0x00000000 0 0xffc00000 0x0 0x00010000>; /* IO */ > > + > > + pcie@0 { > > + ranges; > > + }; > > + }; > > +}; > > + > > +/include/ "fsl/p2020si-post.dtsi" > > -- > > 2.20.1 > >
