CZ.NIC Turris 1.0 and 1.1 are open source routers, they have dual-core PowerPC Freescale P2020 CPU and are based on Freescale P2020RDB-PC-A board. Hardware design is fully open source, all firmware and hardware design files are available at Turris project website: https://docs.turris.cz/hw/turris-1x/turris-1x/ https://project.turris.cz/en/hardware.html Signed-off-by: Pali Rohár <pali@xxxxxxxxxx> --- arch/powerpc/boot/dts/turris1x.dts | 470 +++++++++++++++++++++++++++++ 1 file changed, 470 insertions(+) create mode 100644 arch/powerpc/boot/dts/turris1x.dts diff --git a/arch/powerpc/boot/dts/turris1x.dts b/arch/powerpc/boot/dts/turris1x.dts new file mode 100644 index 000000000000..2a624f117586 --- /dev/null +++ b/arch/powerpc/boot/dts/turris1x.dts @@ -0,0 +1,470 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Turris 1.x Device Tree Source + * + * Copyright 2013 - 2022 CZ.NIC z.s.p.o. (http://www.nic.cz/) + * + * Pinout, Schematics and Altium hardware design files are open source + * and available at: https://docs.turris.cz/hw/turris-1x/turris-1x/ + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/leds/common.h> +/include/ "fsl/p2020si-pre.dtsi" + +/ { + model = "Turris 1.x"; + compatible = "cznic,turris1x", "fsl,P2020RDB-PC"; /* fsl,P2020RDB-PC is required for booting Linux */ + + aliases { + ethernet0 = &enet0; + ethernet1 = &enet1; + ethernet2 = &enet2; + serial0 = &serial0; + serial1 = &serial1; + pci0 = &pci0; + pci1 = &pci1; + pci2 = &pci2; + spi0 = &spi0; + }; + + memory { + device_type = "memory"; + }; + + soc: soc@ffe00000 { + ranges = <0x0 0x0 0xffe00000 0x00100000>; + + i2c@3000 { + /* PCA9557PW GPIO controller for boot config */ + gpio-controller@18 { + compatible = "nxp,pca9557"; + label = "bootcfg"; + reg = <0x18>; + #gpio-cells = <2>; + gpio-controller; + polarity = <0x00>; + }; + + /* STM32F030R8T6 MCU for power control */ + power-control@32 { + /* + * Turris Power Control firmware runs on STM32F0 MCU. + * This firmware is open source and available at: + * https://gitlab.nic.cz/turris/hw/turris_power_control + */ + reg = <0x32>; + }; + + /* SA56004ED temperature control */ + temperature-sensor@4c { + compatible = "nxp,sa56004"; + reg = <0x4c>; + interrupt-parent = <&gpio>; + interrupts = <12 IRQ_TYPE_LEVEL_LOW>, /* GPIO12 - ALERT pin */ + <13 IRQ_TYPE_LEVEL_LOW>; /* GPIO13 - CRIT pin */ + }; + + /* DDR3 SPD/EEPROM */ + eeprom@52 { + compatible = "atmel,spd"; + reg = <0x52>; + }; + + /* ATSHA204-TH-DA-T crypto module */ + crypto@64 { + compatible = "atmel,atsha204"; + reg = <0x64>; + }; + + /* IDT6V49205BNLGI clock generator */ + clock-generator@69 { + compatible = "idt,6v49205b"; + reg = <0x69>; + }; + + /* MCP79402-I/ST Protected EEPROM */ + eeprom@57 { + reg = <0x57>; + }; + + /* MCP79402-I/ST RTC */ + rtc@6f { + compatible = "microchip,mcp7940x"; + reg = <0x6f>; + interrupt-parent = <&gpio>; + interrupts = <14 0>; /* GPIO14 - MFP pin */ + }; + }; + + /* SPI on connector P1 */ + spi0: spi@7000 { + }; + + gpio: gpio-controller@fc00 { + #interrupt-cells = <2>; + interrupt-controller; + }; + + /* Connected to SMSC USB2412-DZK 2-Port USB 2.0 Hub Controller */ + usb@22000 { + phy_type = "ulpi"; + dr_mode = "host"; + }; + + enet0: ethernet@24000 { + /* Connected to port 6 of QCA8337N-AL3C switch */ + phy-connection-type = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + mdio@24520 { + /* QCA8337N-AL3C switch with integrated ethernet PHYs for LAN ports */ + switch@10 { + compatible = "qca,qca8337"; + interrupts = <2 1 0 0>; + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu1"; + ethernet = <&enet1>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan5"; + }; + + port@2 { + reg = <2>; + label = "lan4"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan2"; + }; + + port@5 { + reg = <5>; + label = "lan1"; + }; + + port@6 { + reg = <6>; + label = "cpu0"; + ethernet = <&enet0>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + + /* KSZ9031RNXCA ethernet phy for WAN port */ + phy: ethernet-phy@7 { + interrupts = <3 1 0 0>; + reg = <0x7>; + }; + }; + + ptp_clock@24e00 { + fsl,tclk-period = <5>; + fsl,tmr-prsc = <200>; + fsl,tmr-add = <0xcccccccd>; + fsl,tmr-fiper1 = <0x3b9ac9fb>; + fsl,tmr-fiper2 = <0x0001869b>; + fsl,max-adj = <249999999>; + }; + + enet1: ethernet@25000 { + /* Connected to port 0 of QCA8337N-AL3C switch */ + phy-connection-type = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + mdio@25520 { + status = "disabled"; + }; + + enet2: ethernet@26000 { + /* Connected to KSZ9031RNXCA ethernet phy (WAN port) */ + label = "wan"; + phy-handle = <&phy>; + phy-connection-type = "rgmii-id"; + }; + + mdio@26520 { + status = "disabled"; + }; + + sdhc@2e000 { + bus-width = <4>; + cd-gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + }; + + lbc: localbus@ffe05000 { + reg = <0 0xffe05000 0 0x1000>; + + ranges = <0x0 0x0 0x0 0xef000000 0x01000000>, /* NOR */ + <0x1 0x0 0x0 0xff800000 0x00040000>, /* NAND */ + <0x3 0x0 0x0 0xffa00000 0x00020000>; /* CPLD */ + + /* S29GL128P90TFIR10 NOR */ + nor@0,0 { + compatible = "cfi-flash"; + reg = <0x0 0x0 0x01000000>; + bank-width = <2>; + device-width = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + /* 128 kB for Device Tree Blob */ + reg = <0x00000000 0x00020000>; + label = "dtb"; + }; + + partition@20000 { + /* 1.7 MB for Rescue Linux Kernel Image */ + reg = <0x00020000 0x001a0000>; + label = "rescue-kernel"; + }; + + partition@1c0000 { + /* 1.5 MB for Rescue JFFS2 Root File System */ + reg = <0x001c0000 0x00180000>; + label = "rescue-rootfs"; + }; + + partition@340000 { + /* 11 MB for TAR.XZ Backup with content of NAND Root File System */ + reg = <0x00340000 0x00b00000>; + label = "backup-rootfs"; + }; + + partition@e40000 { + /* 768 kB for Certificates JFFS2 File System */ + reg = <0x00e40000 0x000c0000>; + label = "certificates"; + }; + + /* free unused space 0x00f00000-0x00f20000 */ + + partition@f20000 { + /* 128 kB for U-Boot Environment Variables */ + reg = <0x00f20000 0x00020000>; + label = "u-boot-env"; + }; + + partition@f40000 { + /* 768 kB for U-Boot Bootloader Image */ + reg = <0x00f40000 0x000c0000>; + label = "u-boot"; + }; + }; + }; + + /* MT29F2G08ABAEAWP:E NAND */ + nand@1,0 { + compatible = "fsl,p2020-fcm-nand", "fsl,elbc-fcm-nand"; + reg = <0x1 0x0 0x00040000>; + nand-ecc-mode = "soft"; + nand-ecc-algo = "bch"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + /* 256 MB for UBI with one volume: UBIFS Root File System */ + reg = <0x00000000 0x10000000>; + label = "rootfs"; + }; + }; + }; + + /* LCMXO1200C-3FTN256C FPGA */ + cpld@3,0 { + /* + * Turris CPLD firmware which runs on this Lattice FPGA, + * is extended version of P1021RDB-PC CPLD v4.1 firmware. + * It is backward compatible with its original version + * and the only extension is support for Turris LEDs. + * Turris CPLD firmware is open source and available at: + * https://gitlab.nic.cz/turris/hw/turris_cpld/-/blob/master/CZ_NIC_Router_CPLD.v + */ + compatible = "cznic,turris1x-cpld", "fsl,p1021rdb-pc-cpld", "simple-bus"; + reg = <0x3 0x0 0x30>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x3 0x0 0x00020000>; + + /* MAX6370KA+T watchdog */ + watchdog@2 { + /* + * CPLD firmware maps SET0, SET1 and SET2 + * input logic of MAX6370KA+T chip to CPLD + * memory space at byte offset 0x2. WDI + * input logic is outside of the CPLD and + * connected via external GPIO. + */ + compatible = "maxim,max6370"; + reg = <0x02 0x01>; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + + led-controller@13 { + /* + * LEDs are controlled by CPLD firmware. + * All five LAN LEDs share common RGB settings + * and so it is not possible to set different + * colors on different LAN ports. + */ + compatible = "cznic,turris1x-leds"; + reg = <0x13 0x1d>; + #address-cells = <1>; + #size-cells = <0>; + + multi-led@0 { + reg = <0x0>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_WAN; + }; + + multi-led@1 { + reg = <0x1>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_LAN; + function-enumerator = <5>; + }; + + multi-led@2 { + reg = <0x2>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_LAN; + function-enumerator = <4>; + }; + + multi-led@3 { + reg = <0x3>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_LAN; + function-enumerator = <3>; + }; + + multi-led@4 { + reg = <0x4>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + }; + + multi-led@5 { + reg = <0x5>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + }; + + multi-led@6 { + reg = <0x6>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_WLAN; + }; + + multi-led@7 { + reg = <0x7>; + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_POWER; + }; + }; + }; + }; + + pci2: pcie@ffe08000 { + /* + * PCIe bus for on-board TUSB7340RKM USB 3.0 xHCI controller. + * This xHCI controller is available only on Turris 1.1 boards. + * Turris 1.0 boards have nothing connected to this PCIe bus, + * so system would see only PCIe Root Port of this PCIe Root + * Complex. TUSB7340RKM xHCI controller has four SuperSpeed + * channels. Channel 0 is connected to the front USB 3.0 port, + * channel 1 (but only USB 2.0 subset) to USB 2.0 pins on mPCIe + * slot 1 (CN5), channels 2 and 3 to connector P600. + * + * P2020 PCIe Root Port uses 1MB of PCIe MEM and xHCI controller + * uses 64kB + 8kB of PCIe MEM. No PCIe IO is used or required. + * So allocate 2MB of PCIe MEM for this PCIe bus. + */ + reg = <0 0xffe08000 0 0x1000>; + ranges = <0x02000000 0x0 0xc0000000 0 0xc0000000 0x0 0x00200000>, /* MEM */ + <0x01000000 0x0 0x00000000 0 0xffc20000 0x0 0x00010000>; /* IO */ + + pcie@0 { + ranges; + }; + }; + + pci1: pcie@ffe09000 { + /* PCIe bus on mPCIe slot 2 (CN6) for expansion mPCIe card */ + reg = <0 0xffe09000 0 0x1000>; + ranges = <0x02000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000>, /* MEM */ + <0x01000000 0x0 0x00000000 0 0xffc10000 0x0 0x00010000>; /* IO */ + + pcie@0 { + ranges; + }; + }; + + pci0: pcie@ffe0a000 { + /* + * PCIe bus on mPCIe slot 1 (CN5) for expansion mPCIe card. + * Turris 1.1 boards have in this mPCIe slot additional USB 2.0 + * pins via channel 1 of TUSB7340RKM xHCI controller and also + * additional SIM card slot, both for USB-based WWAN cards. + */ + reg = <0 0xffe0a000 0 0x1000>; + ranges = <0x02000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000>, /* MEM */ + <0x01000000 0x0 0x00000000 0 0xffc00000 0x0 0x00010000>; /* IO */ + + pcie@0 { + ranges; + }; + }; +}; + +/include/ "fsl/p2020si-post.dtsi" -- 2.20.1
