[PATCH v2] ARM: dts: aspeed: Adding Jabil Rubypass BMC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The initial introduction of the jabil server with AST2600 BMC SoC.

Signed-off-by: David Wang <David_Wang6097@xxxxxxxxx>
---
 arch/arm/boot/dts/Makefile                    |   3 +-
 .../boot/dts/aspeed-bmc-jabil-rubypass.dts    | 479 ++++++++++++++++++
 2 files changed, 481 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7c16f8a2b738..9c395178fc89 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1566,4 +1566,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-tyan-s8036.dtb \
 	aspeed-bmc-vegman-n110.dtb \
 	aspeed-bmc-vegman-rx20.dtb \
-	aspeed-bmc-vegman-sx20.dtb
+	aspeed-bmc-vegman-sx20.dtb \
+	aspeed-bmc-jabil-rubypass.dtb
diff --git a/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
new file mode 100644
index 000000000000..77418895705a
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
@@ -0,0 +1,479 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Jabil rbp";
+	compatible = "jabil,rbp", "aspeed,ast2600";
+
+	chosen {
+		bootargs = "console=ttyS4,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	vcc_sdhci0: regulator-vcc-sdhci0 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDHCI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+
+	vccq_sdhci0: regulator-vccq-sdhci0 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHCI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>,
+			 <1800000 0>;
+	};
+
+	vcc_sdhci1: regulator-vcc-sdhci1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SDHCI1 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhci1: regulator-vccq-sdhci1 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHCI1 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio0 ASPEED_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>,
+			 <1800000 0>;
+	};
+
+	leds {
+				compatible = "gpio-leds";
+
+				identify {
+						default-state = "off";
+						gpios = <&gpio0 ASPEED_GPIO(B, 7) GPIO_ACTIVE_LOW>;
+				};
+
+				status_amber {
+						default-state = "off";
+						gpios = <&gpio0 ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
+				};
+
+				status_green {
+						default-state = "keep";
+						gpios = <&gpio0 ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
+				};
+
+				status_susack {
+						default-state = "off";
+						gpios = <&gpio0 ASPEED_GPIO(V, 6) GPIO_ACTIVE_LOW>;
+				};
+
+				fan1_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 0 GPIO_ACTIVE_HIGH>;
+				};
+				fan2_fault{
+						default-state = "off";
+		};
+				fan3_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 2 GPIO_ACTIVE_HIGH>;
+				};
+				fan4_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 3 GPIO_ACTIVE_HIGH>;
+				};
+				fan5_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 4 GPIO_ACTIVE_HIGH>;
+				};
+				fan6_fault{
+						default-state = "off";
+						gpios = <&gpio3_71 5 GPIO_ACTIVE_HIGH>;
+				};
+
+				power_amber {
+						default-state = "off";
+						gpios = <&gpio0 ASPEED_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
+				};
+		};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio1 {
+	status = "okay";
+
+	ethphy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio2 {
+	status = "okay";
+
+	ethphy2: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio3 {
+	status = "okay";
+
+	ethphy3: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+
+&mac1 {
+	status = "okay";
+
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&ethphy1>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default>;
+};
+
+&mac2 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	non-removable;
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	clk-phase-mmc-hs200 = <9>, <225>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <100000000>;
+	};
+};
+
+&uart1 {
+		status = "okay";
+		pinctrl-0 = <&pinctrl_txd1_default
+					&pinctrl_rxd1_default
+					&pinctrl_nrts1_default
+					&pinctrl_ndtr1_default
+					&pinctrl_ndsr1_default
+					&pinctrl_ncts1_default
+					&pinctrl_ndcd1_default
+					&pinctrl_nri1_default>;
+};
+
+&uart2 {
+		status = "okay";
+		pinctrl-0 = <&pinctrl_txd2_default
+					&pinctrl_rxd2_default
+					&pinctrl_nrts2_default
+					&pinctrl_ndtr2_default
+					&pinctrl_ndsr2_default
+					&pinctrl_ncts2_default
+					&pinctrl_ndcd2_default
+					&pinctrl_nri2_default>;
+};
+
+&uart3 {
+		status = "okay";
+};
+
+&uart4 {
+		status = "okay";
+};
+
+
+&i2c0 {
+	status = "okay";
+
+	temp@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	multi-master;
+	status = "okay";
+
+	gpio@70 {
+		compatible = "nxp,pca9538";
+		reg = <0x70>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(O, 7) IRQ_TYPE_EDGE_FALLING>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"presence-fan1-n", "presence-fan2-n", "presence-fan3-n", "presence-fan4-n",
+			"presence-fan5-n", "presence-fan6-n", "", "";
+	};
+
+	gpio3_71:gpio@71 {
+		compatible = "nxp,pca9538";
+		reg = <0x71>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"led-fan1-fault", "led-fan2-fault", "led-fan3-fault", "led-fan4-fault",
+			"led-fan5-fault", "led-fan6-fault", "", "";
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&fsim0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&sdc {
+	status = "okay";
+};
+
+/*
+ * The signal voltage of sdhci0 and sdhci1 on AST2600-A2 EVB is able to be
+ * toggled by GPIO pins.
+ * In the reference design, GPIOV0 of AST2600-A2 EVB is connected to the
+ * power load switch that provides 3.3v to sdhci0 vdd, GPIOV1 is connected to
+ * a 1.8v and a 3.3v power load switch that provides signal voltage to
+ * sdhci0 bus.
+ * If GPIOV0 is active high, sdhci0 is enabled, otherwise, sdhci0 is disabled.
+ * If GPIOV1 is active high, 3.3v power load switch is enabled, sdhci0 signal
+ * voltage is 3.3v, otherwise, 1.8v power load switch will be enabled,
+ * sdhci0 signal voltage becomes 1.8v.
+ * AST2600-A2 EVB also supports toggling signal voltage for sdhci1.
+ * The design is the same as sdhci0, it uses GPIOV2 as power-gpio and GPIOV3
+ * as power-switch-gpio.
+ */
+&sdhci0 {
+	status = "okay";
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	sdhci-drive-type = /bits/ 8 <3>;
+	sdhci-caps-mask = <0x7 0x0>;
+	sdhci,wp-inverted;
+	vmmc-supply = <&vcc_sdhci0>;
+	vqmmc-supply = <&vccq_sdhci0>;
+	clk-phase-sd-hs = <7>, <200>;
+};
+
+&sdhci1 {
+	status = "okay";
+	bus-width = <4>;
+	max-frequency = <100000000>;
+	sdhci-drive-type = /bits/ 8 <3>;
+	sdhci-caps-mask = <0x7 0x0>;
+	sdhci,wp-inverted;
+	vmmc-supply = <&vcc_sdhci1>;
+	vqmmc-supply = <&vccq_sdhci1>;
+	clk-phase-sd-hs = <7>, <200>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
+
+&gpio0 {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/       "","","","","","","","",
+	/*B0-B7*/       "presence-ncsi-i210-n","","","","","","","led-identify-n",
+	/*C0-C7*/       "","","","","","","","",
+	/*D0-D7*/       "","","","","","","","",
+	/*E0-E7*/       "","","","","","","","",
+	/*F0-F7*/       "","","","","","","id-button","",
+	/*G0-G7*/       "","","led-status-green-n","led-status-amber-n","","","","",
+	/*H0-H7*/       "","","","","","cpu-caterr","","cpu1-caterr-n",
+	/*I0-I7*/       "","","","","","","","",
+	/*J0-J7*/       "","","","","","","","",
+	/*K0-K7*/       "","","","","","","","",
+	/*L0-L7*/       "","","","","","","","",
+	/*M0-M7*/       "","","","","","","","",
+	/*N0-N7*/       "","","","","","","","",
+	/*O0-O7*/       "","","","","","","nmi-button","",
+	/*P0-P7*/       "reset-button","reset-out","power-button","power-out","","","","led-hartbeat-n",
+	/*Q0-Q7*/       "","","","","","","","",
+	/*R0-R7*/       "","","","","","","","",
+	/*S0-S7*/       "","","","","","","","",
+	/*T0-T7*/       "","","","","","","","",
+	/*U0-U7*/       "","","","","","","","",
+	/*V0-V7*/       "regulator-vcc-sdhci0","regulator-vccq-sdhci0","regulator-vcc-sdhci1","regulator-vccq-sdhci1","sio-power-good","led-bmc-fw-config-done-n","","",
+	/*W0-W7*/       "","","","","","","","",
+	/*X0-X7*/       "cpu-err2","","","","","","","",
+	/*Y0-Y7*/       "led-power-amber","","","","","","","",
+	/*Z0-Z7*/       "cpu-err0","cpu-err1","","","","","","";
+	};
+
+&gpio1 {
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xCA2>;
+	status = "okay";
+};
+
+&kcs4 {
+	aspeed,lpc-io-reg = <0xCA4>;
+	status = "okay";
+};
+
+&lpc_snoop {
+	snoop-ports = <0x80>;
+	status = "okay";
+};
+
-- 
2.30.2




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux