On Wed, 20 Apr 2022 at 06:55, David Wang <David_Wang6097@xxxxxxxxx> wrote:
>
> The initial introduction of the jabil server with AST2600 BMC SoC.
>
> Signed-off-by: David Wang <David_Wang6097@xxxxxxxxx>
> ---
> .../boot/dts/aspeed-bmc-jabil-rubypass.dts | 383 ++++++++++++++++++
> 1 file changed, 383 insertions(+)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
>
> diff --git a/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
> new file mode 100644
> index 000000000000..80763ff48b2a
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-jabil-rubypass.dts
> @@ -0,0 +1,383 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +
> +/ {
> + model = "Jabil Boy";
> + compatible = "aspeed,ast2600";
add a string for your machine. Something like this:
compatible = "jabil,boy", "aspeed,ast2600";
> +
> + aliases {
> + serial4 = &uart5;
This is in the dsti, so it's not required.
> + };
> +
> + chosen {
> + bootargs = "console=ttyS4,115200n8";
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + reg = <0x80000000 0x80000000>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + identify {
> + default-state = "off";
> + gpios = <&gpio0 ASPEED_GPIO(B, 7) GPIO_ACTIVE_LOW>;
> + };
> +
> + status_amber {
> + default-state = "off";
> + gpios = <&gpio0 ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
> + };
> +
> + status_green {
> + default-state = "keep";
> + gpios = <&gpio0 ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
> + };
> +
> + status_susack {
> + default-state = "off";
> + gpios = <&gpio0 ASPEED_GPIO(V, 6) GPIO_ACTIVE_LOW>;
> + };
> +
> + fan1_fault{
> + default-state = "off";
> + gpios = <&gpio3_71 0 GPIO_ACTIVE_HIGH>;
> + };
> + fan2_fault{
> + default-state = "off"
> + };
> + fan3_fault{
> + default-state = "off";
> + gpios = <&gpio3_71 2 GPIO_ACTIVE_HIGH>;
> + };
> + fan4_fault{
> + default-state = "off";
> + gpios = <&gpio3_71 3 GPIO_ACTIVE_HIGH>;
> + };
> + fan5_fault{
> + default-state = "off";
> + gpios = <&gpio3_71 4 GPIO_ACTIVE_HIGH>;
> + };
> + fan6_fault{
> + default-state = "off";
> + gpios = <&gpio3_71 5 GPIO_ACTIVE_HIGH>;
> + };
> +
> + power_amber {
> + default-state = "off";
> + gpios = <&gpio0 ASPEED_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +&mdio0 {
> + status = "okay";
> +
> + ethphy0: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + };
> +};
> +
> +&mdio1 {
> + status = "okay";
> +
> + ethphy1: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + };
> +};
> +
> +&mdio2 {
> + status = "okay";
> +
> + ethphy2: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + };
> +};
> +
> +&mdio3 {
> + status = "okay";
> +
> + ethphy3: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + };
> +};
> +
> +&mac0 {
> + status = "okay";
> +
> + phy-mode = "rgmii-rxid";
> + phy-handle = <ðphy0>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii1_default>;
> +};
> +
> +
> +&mac1 {
> + status = "okay";
> +
> + phy-mode = "rgmii-rxid";
> + phy-handle = <ðphy1>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii2_default>;
> +};
> +
> +&mac2 {
> + status = "okay";
> +
> + phy-mode = "rgmii";
> + phy-handle = <ðphy2>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii3_default>;
> +};
> +
> +&mac3 {
> + status = "okay";
> +
> + phy-mode = "rgmii";
> + phy-handle = <ðphy3>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii4_default>;
> +};
> +
> +&emmc_controller {
> + status = "okay";
> +};
> +
> +&emmc {
> + non-removable;
> + bus-width = <4>;
> + max-frequency = <100000000>;
> + clk-phase-mmc-hs200 = <9>, <225>;
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> +
> +&fmc {
> + status = "okay";
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "bmc";
> + spi-max-frequency = <50000000>;
> +#include "openbmc-flash-layout-128.dtsi"
> + };
> +};
> +
> +&spi1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi1_default>;
> +
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "pnor";
> + spi-max-frequency = <100000000>;
> + };
> +};
> +
> +&uart1 {
> + status = "okay";
> + pinctrl-0 = <&pinctrl_txd1_default
> + &pinctrl_rxd1_default
> + &pinctrl_nrts1_default
> + &pinctrl_ndtr1_default
> + &pinctrl_ndsr1_default
> + &pinctrl_ncts1_default
> + &pinctrl_ndcd1_default
> + &pinctrl_nri1_default>;
> +};
> +
> +&uart2 {
> + status = "okay";
> + pinctrl-0 = <&pinctrl_txd2_default
> + &pinctrl_rxd2_default
> + &pinctrl_nrts2_default
> + &pinctrl_ndtr2_default
> + &pinctrl_ndsr2_default
> + &pinctrl_ncts2_default
> + &pinctrl_ndcd2_default
> + &pinctrl_nri2_default>;
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "okay";
> +};
> +
> +
> +&uart5 {
> + // Workaround for A0
> + compatible = "snps,dw-apb-uart";
Are you really on an A0? If not, this can be dropped.
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + temp@2e {
> + compatible = "adi,adt7490";
> + reg = <0x2e>;
> + };
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c3 {
> + multi-master;
> + status = "okay";
> +
> + gpio@70 {
> + compatible = "nxp,pca9538";
> + reg = <0x70>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <ASPEED_GPIO(O, 7) IRQ_TYPE_EDGE_FALLING>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names =
> + "FAN1_PRSNT_N", "FAN2_PRSNT_N", "FAN3_PRSNT_N", "FAN4_PRSNT_N",
> + "FAN5_PRSNT_N", "FAN6_PRSNT_N", "FANCTRL1_FANFAIL_N", "FANCTRL2_FANFAIL_N";
> + };
> +
> + gpio3_71:gpio@71 {
> + compatible = "nxp,pca9538";
> + reg = <0x71>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-line-names =
> + "LED_FAN1_FAULT", "LED_FAN2_FAULT", "LED_FAN3_FAULT", "LED_FAN4_FAULT",
> + "LED_FAN5_FAULT", "LED_FAN6_FAULT", "PU_U12_IO6", "PU_U12_IO7";
> + };
> +};
> +
> +&i2c4 {
> + status = "okay";
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2c6 {
> + status = "okay";
> +};
> +
> +&i2c7 {
> + status = "okay";
> +};
> +
> +&i2c8 {
> + status = "okay";
> +};
> +
> +&i2c9 {
> + status = "okay";
> +};
> +
> +&i2c12 {
> + status = "okay";
> +};
> +
> +&i2c13 {
> + status = "okay";
> +};
> +
> +&i2c14 {
> + status = "okay";
> +};
> +
> +&i2c15 {
> + status = "okay";
> +};
> +
> +&fsim0 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&uhci {
> + status = "okay";
> +};
> +
> +&sdc {
> + status = "okay";
> +};
> +
> +&gpio0 {
> + status = "okay";
> + /* Enable GPIOP0 and GPIOP2 pass-through by default */
> + /* pinctrl-names = "pass-through"; */
> + /* pinctrl-0 = <&pinctrl_thru0_default */
> + /* &pinctrl_thru1_default>; */
Commented out? Unless you have a good reason to keep these like this,
please un-comment or remove them.
> +
> + gpio-line-names =
> + /*A0-A7*/ "SMB_DCSCM_I2C2_R_SCL","SMB_DCSCM_I2C2_R_SDA","TP_GPIOA2","TP_GPIOA3","SMB_CPU_PIROM_R_SCL","SMB_CPU_PIROM_R_SDA","SMB_IPMB_STBY_LVC3_R_SCL","SMB_IPMB_STBY_LVC3_R_SDA",
> + /*B0-B7*/ "NCSI_BMC_I210_NCSI_PRSNT_N","NMI_OUT","IRQ_SMB3_M2_ALERT_N","FM_SPD_SWITCH_CTRL_N","RGMII_BMC_RMM4_LVC3_R_MDC","RGMII_BMC_RMM4_LVC3_R_MDIO","FM_BMC_BMCINIT_R","FP_ID_LED_N",
> + /*C0-C7*/ "","RMII_BMC_I210_TXEN_R","RMII_BMC_I210_TXD0_R","RMII_BMC_I210_TXD1_R","","","CLK_50M_BMC_MAC3_NCSI","",
> + /*D0-D7*/ "RMII_BMC_I210_RXD0","RMII_BMC_I210_RXD1","RMII_BMC_I210_CRSDV","RMII_BMC_I210_RXER","","RMII_BMC_OCP3_A_TXEN_R","RMII_BMC_OCP3_A_TXD0_R","RMII_BMC_OCP3_A_TXD1_R",
> + /*E0-E7*/ "","","CLK_50M_BMC_MAC4_NCSI","","RMII_BMC_OCP3_A_RXD0","RMII_BMC_OCP3_A_RXD1","RMII_BMC_OCP3_A_CRSDV","RMII_BMC_OCP3_A_RXER",
> + /*F0-F7*/ "","","","","","","ID_BUTTON","PS_PWROK",
> + /*G0-G7*/ "FM_SMB_BMC_NVME_LVC3_ALERT_N","RST_BMC_I2C_M2_R_N","FP_LED_STATUS_GREEN_N","FP_LED_STATUS_AMBER_N","FM_FORCE_BMC_UPDATE_N","FM_BMC_CRASHLOG_TRIG_N","FM_BMC_CPU_FBRK_OUT_R_N","DBP_PRESENT_IN_R2_N",
> + /*H0-H7*/ "SGPIO_BMC_FPGA_CLK_R","SGPIO_BMC_FPGA_LD_R_N","SGPIO_BMC_FPGA_DOUT_R","SGPIO_BMC_FPGA_DIN","PLTRST_N","CPU_CATERR","PCH_BMC_THERMTRIP","FM_CPU1_CATERR_N",
> + /*I0-I7*/ "JTAG_ASD_NTRST_R_N","JTAG_ASD_TDI_R","JTAG_ASD_TCK_R","JTAG_ASD_TMS_R","JTAG_ASD_TDO","FM_BMC_PWRBTN_OUT_R_N","FM_BMC_PWR_BTN_PTHRU_N","TP_FM_BMC_PCH_SCI_R_N",
> + /*J0-J7*/ "SMB_CHASSENSOR_STBY_LVC3_SCL","SMB_CHASSENSOR_STBY_LVC3_SDA","SMB_FPGA_REG_R_SCL","SMB_FPGA_REG_R_SDA","SMB_DCSCM_I2C12_R_SCL","SMB_DCSCM_I2C12_R_SDA","SMB_BMC_FAN_STBY_LVC3_R_SCL","SMB_BMC_FAN_STBY_LVC3_R_SDA",
> + /*K0-K7*/ "SMB_HSBP_STBY_LVC3_R_SCL","SMB_HSBP_STBY_LVC3_R_SDA","SMB_SMLINK0_STBY_LVC3_R2_SCL","SMB_SMLINK0_STBY_LVC3_R2_SDA","SMB_TEMPSENSOR_STBY_LVC3_R_SCL","SMB_TEMPSENSOR_STBY_LVC3_R_SDA","SMB_PMBUS_SML1_STBY_LVC3_R_SCL","SMB_PMBUS_SML1_STBY_LVC3_R_SDA",
> + /*L0-L7*/ "SMB_PCIE_STBY_LVC3_R_SCL","SMB_PCIE_STBY_LVC3_R_SDA","SMB_HOST_STBY_BMC_LVC3_R_SCL","SMB_HOST_STBY_BMC_LVC3_R_SDA","PREQ_N","TCK_MUX_SEL","","",
> + /*M0-M7*/ "TP_SPA_CTS_N","TP_SPA_DCD_N","TP_SPA_DSR_N","PU_SPA_RI_N","TP_SPA_DTR_N","TP_SPA_RTS_N","SPA_SOUT","SPA_SIN",
> + /*N0-N7*/ "TP_SPB_CTS_N","TP_SPB_DCD_N","TP_SPB_DSR_N","PU_SPB_RI_N","TP_SPB_DTR_N","TP_SPB_RTS_N","UART_BMC_TXD2","UART_BMC_RXD2",
> + /*O0-O7*/ "BMC_FPGA_GPIO_0","BMC_FPGA_GPIO_1","BMC_FPGA_GPIO_2","BMC_FPGA_GPIO_3","FM_BMC_PCH_SPARE_R","FM_CPU1_DISABLE_COD_N","NMI_BUTTON","PDB_PCA9538_INT_N",
> + /*P0-P7*/ "RESET_BUTTON","RESET_OUT","POWER_BUTTON","POWER_OUT","","","DISPLAYPORT_MUX_AUX_R_SEL","BMC_HBLED_N",
> + /*Q0-Q7*/ "TP_BMC_FAN1_A_TACH","TP_BMC_FAN1_B_TACH","TP_BMC_FAN2_A_TACH","TP_BMC_FAN2_B_TACH","TP_BMC_FAN3_A_TACH","TP_BMC_FAN3_B_TACH","TP_BMC_FAN4_A_TACH","TP_BMC_FAN4_B_TACH",
> + /*R0-R7*/ "","","","","","FPGA_JTAG_MUX_SEL","DISPLAYPORT_MUX_R_OE","DISPLAYPORT_MUX_DX_R_SEL",
> + /*S0-S7*/ "RST_BMC_PCIE_MUX_N","BMC_RST_RTCRST_R","PRDY_N","FM_FLASH_SECURITY_STRAP","RST_IPMB_SWITCH_R_N","A_P3V_BAT_SCALED_EN","REMOTE_DEBUG_ENABLE","FM_PCHHOT_N",
> + /*T0-T7*/ "GND","GND","GND","GND","GND","GND","GND","GND",
> + /*U0-U7*/ "GND","GND","GND","GND","GND","GND","GND","GND",
> + /*V0-V7*/ "SIO_S3","SIO_S5","TP_BMC_SIO_PWREQ_N","SIO_ONCONTROL","SIO_POWER_GOOD","LED_BMC_FW_CONFIG_DONE_N","FM_BMC_SUSACK_N","TP_IRQ_BMC_PCH_SMI_LPC_N_R",
> + /*W0-W7*/ "ESPI_IO0_LPC_LAD0_R","ESPI_IO1_LPC_LAD1_R","ESPI_IO2_LPC_LAD2_R","ESPI_IO3_LPC_LAD3_R","CLK_24M_66M_LPC0_ESPI_BMC","ESPI_CS0_N_LFRAME_N_BMC","IRQ_LPC_SERIRQ_ESPI_ALERT_N","RST_LPC_LRST_ESPI_RST_BMC_R_N",
> + /*X0-X7*/ "CPU_ERR2","SMI","POST_COMPLETE","TP_SPI_BMC_SAFS_R_CLK","TP_SPI_BMC_SAFS_R_MOSI","TP_SPI_BMC_SAFS_R_MISO","TP_SPI_BMC_SAFS_R_IO2","TP_SPI_BMC_SAFS_R_IO3",
> + /*Y0-Y7*/ "BMC_PWR_AMB_LED_R_N","IRQ_SML0_ALERT_BMC_R2_N","JTAG_CPLD_BMC_MUX_R_SEL","IRQ_SML1_PMBUS_BMC_ALERT_N","SPI_BMC_BOOT_R_IO2","SPI_BMC_BOOT_R_IO3","PU_SPI_BMC_BOOT_ABR","PU_SPI_BMC_BOOT_WP_N",
> + /*Z0-Z7*/ "CPU_ERR0","CPU_ERR1","PU_TP_PWRGD_P3V3_RISER2","PU_GPIOZ3","PU_GPIOZ4","PU_GPIOZ5","PU_GPIOZ6","PU_GPIOZ7";
I see you've not used any of the OpenBMC naming conventions for your
GPIOs. Can you explain why?
> +};
> +
> +&gpio1 {
> + status = "okay";
> + gpio-line-names = /* GPIO18 A-E */
> + /*A0-A7*/ "TP_GPIO18B5","TP_GPIO18B4","RST_EMMC_BMC_R_N","","","","","",
> + /*B0-B7*/ "","","PD_GPIOB2","","RGMII_BMC_RMM4_TX_R_CLK","RGMII_BMC_RMM4_TX_R_CTRL","RGMII_BMC_RMM4_R_TXD0","RGMII_BMC_RMM4_R_TXD1",
> + /*C0-C7*/ "RGMII_BMC_RMM4_R_TXD2","RGMII_BMC_RMM4_R_TXD3","RGMII_BMC_RMM4_RX_CLK","RGMII_BMC_RMM4_RX_CTRL","RGMII_BMC_RMM4_RXD0","RGMII_BMC_RMM4_RXD1","RGMII_BMC_RMM4_RXD2","RGMII_BMC_RMM4_RXD3",
> + /*D0-D7*/ "EMMC_BMC_R_CLK","EMMC_BMC_R_CMD","EMMC_BMC_R_DATA0","EMMC_BMC_R_DATA1","EMMC_BMC_R_DATA2","EMMC_BMC_R_DATA3","EMMC_BMC_CD_N","EMMC_BMC_WP_N",
> + /*E0-E3*/ "EMMC_BMC_R_DATA4","EMMC_BMC_R_DATA5","EMMC_BMC_R_DATA6","EMMC_BMC_R_DATA7";
> +};
> +
> +&lpc_snoop {
> + snoop-ports = <0x80>;
> + status = "okay";
> +};
> +
> --
> 2.30.2
>
