On 2022-05-14 22:01:32, Dmitry Baryshkov wrote:
> Add DT entries for the second DWC3 USB host, which is limited to the
Nit: drop -the, and perhaps reword the ", and" bit below.
- Marijn
> USB2.0 (HighSpeed), and the corresponding QUSB PHY.
>
> Reviewed-by: Marijn Suijten <marijn.suijten@xxxxxxxxxxxxxx>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/sdm630.dtsi | 55 ++++++++++++++++++++++++++++
> 1 file changed, 55 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi
> index eb8504e5735c..2b5dbc12bdf8 100644
> --- a/arch/arm64/boot/dts/qcom/sdm630.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi
> @@ -1270,6 +1270,20 @@ qusb2phy0: phy@c012000 {
> status = "disabled";
> };
>
> + qusb2phy1: phy@c014000 {
> + compatible = "qcom,sdm660-qusb2-phy";
> + reg = <0x0c014000 0x180>;
> + #phy-cells = <0>;
> +
> + clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
> + <&gcc GCC_RX1_USB2_CLKREF_CLK>;
> + clock-names = "cfg_ahb", "ref";
> +
> + resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
> + nvmem-cells = <&qusb2_hstx_trim>;
> + status = "disabled";
> + };
> +
> sdhc_2: sdhci@c084000 {
> compatible = "qcom,sdm630-sdhci", "qcom,sdhci-msm-v5";
> reg = <0x0c084000 0x1000>;
> @@ -1375,6 +1389,47 @@ opp-384000000 {
> };
> };
>
> + usb2: usb@c2f8800 {
> + compatible = "qcom,sdm660-dwc3", "qcom,dwc3";
> + reg = <0x0c2f8800 0x400>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clocks = <&gcc GCC_CFG_NOC_USB2_AXI_CLK>,
> + <&gcc GCC_USB20_MASTER_CLK>,
> + <&gcc GCC_USB20_MOCK_UTMI_CLK>,
> + <&gcc GCC_USB20_SLEEP_CLK>;
> + clock-names = "cfg_noc", "core",
> + "mock_utmi", "sleep";
> +
> + assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>,
> + <&gcc GCC_USB20_MASTER_CLK>;
> + assigned-clock-rates = <19200000>, <60000000>;
> +
> + interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "hs_phy_irq";
> +
> + qcom,select-utmi-as-pipe-clk;
> +
> + resets = <&gcc GCC_USB_20_BCR>;
> +
> + usb2_dwc3: usb@c200000 {
> + compatible = "snps,dwc3";
> + reg = <0x0c200000 0xc8d0>;
> + interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
> + snps,dis_u2_susphy_quirk;
> + snps,dis_enblslpm_quirk;
> +
> + /* This is the HS-only host */
> + maximum-speed = "high-speed";
> + phys = <&qusb2phy1>;
> + phy-names = "usb2-phy";
> + snps,hird-threshold = /bits/ 8 <0>;
> + };
> + };
> +
> mmcc: clock-controller@c8c0000 {
> compatible = "qcom,mmcc-sdm630";
> reg = <0x0c8c0000 0x40000>;
> --
> 2.35.1
>
