Re: [PATCH v4 02/12] ath11k: Add HW params for WCN6750

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 4/27/2022 10:51 AM, Kalle Valo wrote:
Manikanta Pubbisetty <quic_mpubbise@xxxxxxxxxxx> writes:

Add HW params for WCN6750. It is similar to the HW params
of QCA6390 with few differences wrt DP APIs and register
offsets.

Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@xxxxxxxxxxx>
---
  drivers/net/wireless/ath/ath11k/core.c | 61 ++++++++++++++++++++++++++
  drivers/net/wireless/ath/ath11k/core.h |  1 +
  drivers/net/wireless/ath/ath11k/qmi.h  |  2 +
  3 files changed, 64 insertions(+)

diff --git a/drivers/net/wireless/ath/ath11k/core.c b/drivers/net/wireless/ath/ath11k/core.c
index cbac1919867f..8695f999acb2 100644
--- a/drivers/net/wireless/ath/ath11k/core.c
+++ b/drivers/net/wireless/ath/ath11k/core.c
@@ -427,6 +427,67 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
  		.dbr_debug_support = false,
  		.global_reset = true,
  	},
+	{
+		.name = "wcn6750 hw1.0",
+		.hw_rev = ATH11K_HW_WCN6750_HW10,
+		.fw = {
+			.dir = "WCN6750/hw1.0",
+			.board_size = 256 * 1024,
+			.cal_offset = 128 * 1024,
+		},
+		.max_radios = 1,
+		.bdf_addr = 0x4B0C0000,
+		.ring_mask = &ath11k_hw_ring_mask_qca6390,
+		.internal_sleep_clock = false,
+		.qmi_service_ins_id = ATH11K_QMI_WLFW_SERVICE_INS_ID_V01_WCN6750,
+		.host_ce_config = ath11k_host_ce_config_qca6390,
+		.ce_count = 9,
+		.target_ce_config = ath11k_target_ce_config_wlan_qca6390,
+		.target_ce_count = 9,
+		.svc_to_ce_map = ath11k_target_service_to_ce_map_wlan_qca6390,
+		.svc_to_ce_map_len = 14,
+		.rfkill_pin = 0,
+		.rfkill_cfg = 0,
+		.rfkill_on_level = 0,
+		.single_pdev_only = true,
+		.rxdma1_enable = false,
+		.num_rxmda_per_pdev = 1,
+		.rx_mac_buf_ring = true,
+		.vdev_start_delay = true,
+		.htt_peer_map_v2 = false,
+
+		.spectral = {
+			.fft_sz = 0,
+			.fft_pad_sz = 0,
+			.summary_pad_sz = 0,
+			.fft_hdr_len = 0,
+			.max_fft_bins = 0,
+		},
+
+		.interface_modes = BIT(NL80211_IFTYPE_STATION) |
+					BIT(NL80211_IFTYPE_AP),
+		.supports_monitor = false,
+		.supports_shadow_regs = true,
+		.idle_ps = true,
+		.supports_sta_ps = true,
+		.cold_boot_calib = false,
+		.fw_mem_mode = 0,
+		.num_vdevs = 16 + 1,
+		.num_peers = 512,
+		.supports_suspend = false,
+		.supports_regdb = true,
+		.fix_l1ss = false,
+		.credit_flow = true,
+		.max_tx_ring = DP_TCL_NUM_RING_MAX_QCA6390,
+		.hal_params = &ath11k_hw_hal_params_qca6390,
+		.supports_dynamic_smps_6ghz = false,
+		.alloc_cacheable_memory = false,
+		.supports_rssi_stats = true,
+		.fw_wmi_diag_event = false,
+		.current_cc_support = true,
+		.dbr_debug_support = false,
+		.global_reset = false,
+	},

In the pending branch I added:

+               .bios_sar_capa = NULL,


This is the only other change I had in V5, thanks for adding this.

Manikanta



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux