On 4/19/2022 4:54 PM, Srinivasa Rao Mandadapu wrote:
On 4/18/2022 10:15 PM, Matthias Kaehlcke wrote:
Thanks for your time and valuable inputs Matthias!!!
On Mon, Apr 18, 2022 at 07:44:10PM +0530, Srinivasa Rao Mandadapu wrote:
Add wcd938x and max98360a codecs for audio use case on
sc7280 based platforms.
Add tlmm gpio property in wcd938x node for switching CTIA/OMTP Headset.
Add amp_en node for max98360a codec.
General note: I don't think it's a good practice to add stuff like
this to
multiple boards in a single patch. Why?
First the subject of such a patch tends to be vague ("arm64: dts: qcom:
sc7280: Add nodes for wcd9385 and max98360a codec"), in this case it
gives
no hint about the boards. If someone was interested in picking changes
for a given board they can't easily identify from the subject that the
change is relevant for them.
Changes touching multiple boards are more likely to cause conflicts when
being picked (or reverted), both upstream and in downstream trees (which
unfortunately have to exist for product development). Downstream trees
might only pick changes for the board(s) they target, patches that touch
mutiple boards often cause conflicts due to context deltas in the
'irrelevant' boards.
Lastly it's usually easier to get a patch reviewed (in the sense of
getting a 'Reviewed-by' tag) and landed that does a single thing.
Yes, agree to your opinion. In a nutshell, we will include board
name(ex: herobrine)
in commit message and split the patches per external codec.
Actually, in Initial herobrine boards, EVT and IDP, has both maxim
speaker and WCD codec,
hence we included in same patch.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@xxxxxxxxxxx>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@xxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts | 6 ++
arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi | 8 +++
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 97
++++++++++++++++++++++++++
3 files changed, 111 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
b/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
index 344338a..aa0bf6e2 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
@@ -87,6 +87,12 @@ ap_ts_pen_1v8: &i2c13 {
pins = "gpio51";
};
+&wcd938x {
+ pinctrl-names = "default";
+ pinctrl-0 = <&us_euro_hs_sel>;
+ us-euro-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+};
Since this is added for the CRD rev3 it probably should also be added to
sc7280-herobrine-crd.dts
Okay. Will add in corresponding latest herobrine CRD dts file also.
+
&tlmm {
tp_int_odl: tp-int-odl {
pins = "gpio7";
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
index d58045d..f247403 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
@@ -20,6 +20,14 @@
#include "sc7280-chrome-common.dtsi"
/ {
+ max98360a: audio-codec-0 {
+ compatible = "maxim,max98360a";
+ pinctrl-names = "default";
+ pinctrl-0 = <&_en>;
+ sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+ #sound-dai-cells = <0>;
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 2f863c0..8dad599 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -20,6 +20,42 @@
serial1 = &uart7;
};
+ max98360a: audio-codec-0 {
+ compatible = "maxim,max98360a";
+ pinctrl-names = "default";
+ pinctrl-0 = <&_en>;
+ sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+ #sound-dai-cells = <0>;
+ };
+
+ wcd938x: audio-codec-1 {
Why 'wcd938x' and not 'wcd9385'?
Actually same driver is used for both wcd9380 and wcd9385. Here we can
use specific name as per board.
Will change accordingly.
At present, dt-bindgs also has wcd938x. So will update the name in
bindings and here post this series.
is it okay?
+ compatible = "qcom,wcd9385-codec";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&wcd_reset_n>;
+ pinctrl-1 = <&wcd_reset_n_sleep>;
+
+ reset-gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
+
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+
+ vdd-rxtx-supply = <&vreg_l18b_1p8>;
+ vdd-io-supply = <&vreg_l18b_1p8>;
+ vdd-buck-supply = <&vreg_l17b_1p8>;
+ vdd-mic-bias-supply = <&vreg_bob>;
+
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000
237000 500000 500000
+ 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ #sound-dai-cells = <1>;
+ };
Also add this node to sc7280-herobrine-crd.dts?
Okay. will do accordingly.
+
gpio-keys {
compatible = "gpio-keys";
label = "gpio-keys";
@@ -238,6 +274,19 @@
modem-init;
};
+&lpass_rx_macro {
+ status = "okay";
+};
+
+&lpass_tx_macro {
+ status = "okay";
+};
+
+&lpass_va_macro {
+ status = "okay";
+ vdd-micb-supply = <&vreg_bob>;
+};
Enable these also in sc7280-herobrine.dtsi if other nodes are added to
sc7280-herobrine-crd.dts.
Okay.
+
&pcie1 {
status = "okay";
perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
@@ -298,6 +347,26 @@
cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
};
+&swr0 {
+ status = "okay";
nit: add an empty line between properties and nodes
Okay.
+ wcd_rx: codec@0,4 {
+ compatible = "sdw20217010d00";
+ reg = <0 4>;
+ #sound-dai-cells = <1>;
+ qcom,rx-port-mapping = <1 2 3 4 5>;
+ };
+};
+
+&swr1 {
+ status = "okay";
ditto
Okay.
+ wcd_tx: codec@0,3 {
+ compatible = "sdw20217010d00";
+ reg = <0 3>;
+ #sound-dai-cells = <1>;
+ qcom,tx-port-mapping = <1 2 3 4>;
+ };
+};
Also add these to sc7280-herobrine-crd.dts?
Okay.
+
&uart5 {
compatible = "qcom,geni-debug-uart";
status = "okay";
@@ -561,6 +630,12 @@
};
&tlmm {
+ amp_en: amp-en {
+ pins = "gpio63";
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+
bt_en: bt-en {
pins = "gpio85";
function = "gpio";
@@ -643,6 +718,28 @@
function = "gpio";
bias-pull-down;
};
+
+ us_euro_hs_sel: us-euro-hs-sel {
+ pins = "gpio81";
+ function = "gpio";
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+
+ wcd_reset_n: wcd-reset-n {
+ pins = "gpio83";
+ function = "gpio";
+ drive-strength = <8>;
+ output-high;
+ };
+
+ wcd_reset_n_sleep: wcd-reset-n-sleep {
+ pins = "gpio83";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ output-low;
+ };
Also add to sc7280-herobrine-crd.dts if the other nodes are added.
Okay.
