On Tue, 2022-03-29 at 16:23 +0200, Matthias Brugger wrote:
>
> On 29/03/2022 12:17, Tinghan Shen wrote:
> > Hi Matthias,
> >
> > Thanks for your comment.
> >
> > On Mon, 2022-03-28 at 14:26 +0200, Matthias Brugger wrote:
> > >
> > > On 16/02/2022 12:31, Tinghan Shen wrote:
> > > > Add basic chip support for mediatek mt8195.
> > > >
> > > > Signed-off-by: Seiya Wang <seiya.wang@xxxxxxxxxxxx>
> > > > Signed-off-by: Tinghan Shen <tinghan.shen@xxxxxxxxxxxx>
> > > > Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx>
> > > > ---
> > > > arch/arm64/boot/dts/mediatek/Makefile | 1 +
> > > > arch/arm64/boot/dts/mediatek/mt8195-evb.dts | 161 +++
> > > > arch/arm64/boot/dts/mediatek/mt8195.dtsi | 1049 +++++++++++++++++++
> > > > 3 files changed, 1211 insertions(+)
> > > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-evb.dts
> > > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8195.dtsi
> > > >
> > > > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> > > > index 8c1e18032f9f..5da29e7223e4 100644
> > > > --- a/arch/arm64/boot/dts/mediatek/Makefile
> > > > +++ b/arch/arm64/boot/dts/mediatek/Makefile
> > > > @@ -38,4 +38,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb
> > > > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
> > > > diff --git a/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
> > > > b/arch/arm64/boot/dts/mediatek/mt8195-
> > > > evb.dts
> > > > new file mode 100644
> > > > index 000000000000..51633d91d984
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
> > > > @@ -0,0 +1,161 @@
> > >
> > > [...]
> > > > +
> > > > +&u2port0 {
> > > > + status = "okay";
> > > > +};
> > > > +
> > > > +&u2port1 {
> > > > + status = "okay";
> > > > +};
> > > > +
> > > > +&u3phy0 {
> > > > + status="okay";
> > > > +};
> > > > +
> > > > +&u3phy1 {
> > > > + status="okay";
> > > > +};
> > > > +
> > >
> > > So we enable phys for xhci but not the device. Are we missing anything to enable
> > > them on the EVB?
> >
> > after discussed with usb expert, we think that we're missing the xhci nodes.
> > I'll add xhci nodes at next version.
> >
> > >
> > > > +&uart0 {
> > > > + pinctrl-names = "default";
> > > > + pinctrl-0 = <&uart0_pin>;
> > > > + status = "okay";
> > > > +};
> > > > diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> > > > b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> > > > new file mode 100644
> > > > index 000000000000..a363e82f6988
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> > > > @@ -0,0 +1,1049 @@
> > >
> > > [...]
> > > > +
> > > > + clk32k: oscillator-32k {
> > > > + compatible = "fixed-clock";
> > > > + #clock-cells = <0>;
> > > > + clock-frequency = <32768>;
> > > > + clock-output-names = "clk32k";
> > >
> > > I suppose the 32KHz oscillator is really present on the board also not used by
> > > any device (up to now?).
> >
> > Yes. 32KHz clock is still available on MT8195.
> > Some modules can choose 32K as clock source depending on requirements.
> >
>
> Thanks for the confirmation.
>
> > >
> > > [...]
> > > > +
> > > > + soc {
> > > > + #address-cells = <2>;
> > > > + #size-cells = <2>;
> > > > + compatible = "simple-bus";
> > > > + ranges;
> > > > +
> > >
> > > [...]
> > > > +
> > > > + pwrap: pwrap@10024000 {
> > > > + compatible = "mediatek,mt8195-pwrap", "syscon";
> > > > + reg = <0 0x10024000 0 0x1000>;
> > > > + reg-names = "pwrap";
> > > > + interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>;
> > > > + clocks = <&infracfg_ao CLK_INFRA_AO_PMIC_AP>,
> > > > + <&infracfg_ao CLK_INFRA_AO_PMIC_TMR>;
> > > > + clock-names = "spi", "wrap";
> > >
> > > Binding mandates resets but not present here. It also mandates two register
> > > regions, but only one is given here.
> >
> > After discussed with pwrap experts, the pwrap binding is out-of-date for mt8195.
> > They will send a patch to fix pwrap binding.
> >
>
> If possible can you add the patch fixing the pwrap binding in this series, then
> I don't have to search for the dependencies in my inbox. That would be of great
> help.
No problem. I'll add it to this series when the patch is ready.
Best regards,
Tinghan
>
> > >
> > > > + assigned-clocks = <&topckgen CLK_TOP_PWRAP_ULPOSC>;
> > > > + assigned-clock-parents = <&topckgen CLK_TOP_ULPOSC1_D10>;
> > > > + };
> > > > +
> > > > + scp_adsp: clock-controller@10720000 {
> > > > + compatible = "mediatek,mt8195-scp_adsp";
> > > > + reg = <0 0x10720000 0 0x1000>;
> > > > + #clock-cells = <1>;
> > > > + };
> > > > +
> > >
> > > [...]
> > >
> > > > +
> > > > + mmc0: mmc@11230000 {
> > > > + compatible = "mediatek,mt8195-mmc",
> > > > + "mediatek,mt8183-mmc";
> > > > + reg = <0 0x11230000 0 0x10000>,
> > > > + <0 0x11f50000 0 0x1000>;
> > >
> > > Seems to be an oversight when adding support for mt8183-mmc support to the
> > > driver. The binding description is missing the optional host top register base.
> > > Chaotian can you please help to fix this in the binding description.
> >
> > Ok. I'll fix it at next version.
> >
>
> I'm not sure what you mean. I suppose the way forward is to fix the binding
> description, correct?
>
> Thanks,
> Matthias
>
> > >
> > > > + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH 0>;
> > > > + clocks = <&topckgen CLK_TOP_MSDC50_0>,
> > > > + <&infracfg_ao CLK_INFRA_AO_MSDC0>,
> > > > + <&infracfg_ao CLK_INFRA_AO_MSDC0_SRC>;
> > > > + clock-names = "source", "hclk", "source_cg";
> > > > + status = "disabled";
> > > > + };
> > > > +
> > >
> > > [...]
> > > > +
> > > > + xhci3: usb@112b0000 {
> > > > + compatible = "mediatek,mt8195-xhci",
> > > > + "mediatek,mtk-xhci";
> > > > + reg = <0 0x112b0000 0 0x1000>,
> > > > + <0 0x112b3e00 0 0x0100>;
> > > > + reg-names = "mac", "ippc";
> > > > + interrupts = <GIC_SPI 536 IRQ_TYPE_LEVEL_HIGH 0>;
> > > > + phys = <&u2port3 PHY_TYPE_USB2>;
> > > > + assigned-clocks = <&topckgen CLK_TOP_USB_TOP_3P>,
> > > > + <&topckgen CLK_TOP_SSUSB_XHCI_3P>;
> > > > + assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
> > > > + <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
> > > > + clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_3P_BUS>,
> > > > + <&topckgen CLK_TOP_SSUSB_P3_REF>,
> > > > + <&pericfg_ao CLK_PERI_AO_SSUSB_3P_XHCI>;
> > > > + clock-names = "sys_ck", "ref_ck", "xhci_ck";
> > > > + /* This controller is connected with a BT device.
> > > > + * Disable usb2 lpm to prevent konwn issues.
> > > > + */
> > > > + usb2-lpm-disable;
> > >
> > > My understanding is, that this depends on the board and not the SoC. Which means
> > > usb2-lpm-disable should go into any board that has a BT device connected to the
> > > xhci device (I don't see any active xhci node in mt8195-evb so far).
> >
> > Ok. I'll move this property to evb board in a xhci node.
> >
> > Best regards,
> > TingHan
> >
> > >
> > > Regards,
> > > Matthias
