Add support for the temperatur sensor and the fan controller on the Microchip LAN966x SoC. Apparently, an Analog Bits PVT sensor is used which can measure temperature and process voltages. But only a forumlae for the temperature sensor is known. Additionally, the SoC support a fan tacho input as well as a PWM signal to control the fan. Signed-off-by: Michael Walle <michael@xxxxxxxx> --- Just in case someone is curious why the I state the datasheet is wrong on the PWM frequency: The actual PWM frequency was verified by measuring the output with an oscilloscope. Also you can write a '0' as the PWM frequency which would result in div-by-zero; but what happens is that the output frequency will be half the frequency of a setting of '1'. Documentation/hwmon/lan966x.rst | 47 ++++ drivers/hwmon/Kconfig | 12 + drivers/hwmon/Makefile | 1 + drivers/hwmon/lan966x-hwmon.c | 390 ++++++++++++++++++++++++++++++++ 4 files changed, 450 insertions(+) create mode 100644 Documentation/hwmon/lan966x.rst create mode 100644 drivers/hwmon/lan966x-hwmon.c diff --git a/Documentation/hwmon/lan966x.rst b/Documentation/hwmon/lan966x.rst new file mode 100644 index 000000000000..00c93539d842 --- /dev/null +++ b/Documentation/hwmon/lan966x.rst @@ -0,0 +1,47 @@ +.. SPDX-License-Identifier: GPL-2.0 + +Kernel driver lan966x-hwmon +=========================== + +Supported chips: + + * Microchip LAN9668 (sensor in SoC) + + Prefix: 'lan9668-hwmon' + + Datasheet: https://microchip-ung.github.io/lan9668_reginfo + +Authors: + + Michael Walle <michael@xxxxxxxx> + +Description +----------- + +This driver implements support for the Microchip LAN9668 on-chip +temperature sensor as well as its fan controller. It provides one +temperature sensor and one fan controller. The temperature range +of the sensor is specified from -40 to +125 degrees Celsius and +its accuracy is +/- 5 degrees Celsius. The fan controller has a +tacho input and a PWM output with a customizable PWM output +frequency from ~20Hz to ~650kHz + +No alarms are supported by the SoC. + +temperature sensor chips. TMP464 provides one local and four remote +sensors. TMP468 provides one local and eight remote sensors. +Temperature is measured in degrees Celsius. The chips are wired over +I2C/SMBus and specified over a temperature range of -40 to +125 degrees +Celsius. Resolution for both the local and remote channels is 0.0625 +degree C. + +The driver exports temperature values, fan tacho input and PWM settings +via the following sysfs files: + +**temp1_input** + +**fan1_input** + +**pwm1** + +**pwm1_freq** diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index be9773270e53..26a60e1eebbc 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -815,6 +815,18 @@ config SENSORS_POWR1220 This driver can also be built as a module. If so, the module will be called powr1220. +config SENSORS_LAN966X + tristate "Microchip LAN966x Hardware Monitoring" + depends on SOC_LAN966 || COMPILE_TEST + depends on REGMAP + select POLYNOMIAL + help + If you say yes here you get support for temperature monitoring + on the Microchip LAN966x SoC. + + This driver can also be built as a module. If so, the module + will be called lan966x-hwmon. + config SENSORS_LINEAGE tristate "Lineage Compact Power Line Power Entry Module" depends on I2C diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 8a03289e2aa4..51ca6956f8b7 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -100,6 +100,7 @@ obj-$(CONFIG_SENSORS_IT87) += it87.o obj-$(CONFIG_SENSORS_JC42) += jc42.o obj-$(CONFIG_SENSORS_K8TEMP) += k8temp.o obj-$(CONFIG_SENSORS_K10TEMP) += k10temp.o +obj-$(CONFIG_SENSORS_LAN966X) += lan966x-hwmon.o obj-$(CONFIG_SENSORS_LINEAGE) += lineage-pem.o obj-$(CONFIG_SENSORS_LOCHNAGAR) += lochnagar-hwmon.o obj-$(CONFIG_SENSORS_LM63) += lm63.o diff --git a/drivers/hwmon/lan966x-hwmon.c b/drivers/hwmon/lan966x-hwmon.c new file mode 100644 index 000000000000..d0db2de6c7e8 --- /dev/null +++ b/drivers/hwmon/lan966x-hwmon.c @@ -0,0 +1,390 @@ +// SPDX-License-Identifier: GPL-2.0-only + +#include <linux/bitfield.h> +#include <linux/clk.h> +#include <linux/hwmon.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/mod_devicetable.h> +#include <linux/platform_device.h> +#include <linux/polynomial.h> +#include <linux/regmap.h> + +/* + * The original translation formulae of the temperature (in degrees of Celsius) + * are as follows: + * + * T = -3.4627e-11*(N^4) + 1.1023e-7*(N^3) + -1.9165e-4*(N^2) + + * 3.0604e-1*(N^1) + -5.6197e1 + * + * where [-56.197, 136.402]C and N = [0, 1023]. + * + * They must be accordingly altered to be suitable for the integer arithmetics. + * The technique is called 'factor redistribution', which just makes sure the + * multiplications and divisions are made so to have a result of the operations + * within the integer numbers limit. In addition we need to translate the + * formulae to accept millidegrees of Celsius. Here what it looks like after + * the alterations: + * + * T = -34627e-12*(N^4) + 110230e-9*(N^3) + -191650e-6*(N^2) + + * 306040e-3*(N^1) + -56197 + * + * where T = [-56197, 136402]mC and N = [0, 1023]. + */ + +static const struct polynomial poly_N_to_temp = { + .terms = { + {4, -34627, 1000, 1}, + {3, 110230, 1000, 1}, + {2, -191650, 1000, 1}, + {1, 306040, 1000, 1}, + {0, -56197, 1, 1} + } +}; + +#define PVT_SENSOR_CTRL 0x0 /* unused */ +#define PVT_SENSOR_CFG 0x4 +#define SENSOR_CFG_CLK_CFG GENMASK(27, 20) +#define SENSOR_CFG_TRIM_VAL GENMASK(13, 9) +#define SENSOR_CFG_SAMPLE_ENA BIT(8) +#define SENSOR_CFG_START_CAPTURE BIT(7) +#define SENSOR_CFG_CONTINIOUS_MODE BIT(6) +#define SENSOR_CFG_PSAMPLE_ENA GENMASK(1, 0) +#define PVT_SENSOR_STAT 0x8 +#define SENSOR_STAT_DATA_VALID BIT(10) +#define SENSOR_STAT_DATA GENMASK(9, 0) + +#define FAN_CFG 0x0 +#define FAN_CFG_DUTY_CYCLE GENMASK(23, 16) +#define INV_POL BIT(3) +#define GATE_ENA BIT(2) +#define PWM_OPEN_COL_ENA BIT(1) +#define FAN_STAT_CFG BIT(0) +#define FAN_PWM_FREQ 0x4 +#define FAN_PWM_CYC_10US GENMASK(25, 15) +#define FAN_PWM_FREQ_FREQ GENMASK(14, 0) +#define FAN_CNT 0xc +#define FAN_CNT_DATA GENMASK(15, 0) + +struct lan966x_hwmon { + struct regmap *regmap_pvt; + struct regmap *regmap_fan; + struct clk *clk; + unsigned long clk_rate; +}; + +static int lan966x_hwmon_read_temp(struct device *dev, long *val) +{ + struct lan966x_hwmon *hwmon = dev_get_drvdata(dev); + unsigned int data; + int ret; + + ret = regmap_read(hwmon->regmap_pvt, PVT_SENSOR_STAT, &data); + if (ret < 0) + return ret; + + if (!(data & SENSOR_STAT_DATA_VALID)) + return -ENODATA; + + *val = polynomial_calc(&poly_N_to_temp, + FIELD_GET(SENSOR_STAT_DATA, data)); + + return 0; +} + +static int lan966x_hwmon_read_fan(struct device *dev, long *val) +{ + struct lan966x_hwmon *hwmon = dev_get_drvdata(dev); + unsigned int data; + int ret; + + ret = regmap_read(hwmon->regmap_fan, FAN_CNT, &data); + if (ret < 0) + return ret; + + /* + * Data is given in pulses per second. Assume two pulses + * per revolution. + */ + *val = FIELD_GET(FAN_CNT_DATA, data) * 60 / 2; + + return 0; +} + +static int lan966x_hwmon_read_pwm(struct device *dev, long *val) +{ + struct lan966x_hwmon *hwmon = dev_get_drvdata(dev); + unsigned int data; + int ret; + + ret = regmap_read(hwmon->regmap_fan, FAN_CFG, &data); + if (ret < 0) + return ret; + + *val = FIELD_GET(FAN_CFG_DUTY_CYCLE, data); + + return 0; +} + +static int lan966x_hwmon_read_pwm_freq(struct device *dev, long *val) +{ + struct lan966x_hwmon *hwmon = dev_get_drvdata(dev); + unsigned long tmp; + unsigned int data; + int ret; + + ret = regmap_read(hwmon->regmap_fan, FAN_PWM_FREQ, &data); + if (ret < 0) + return ret; + + /* + * Datasheet says it is sys_clk / 256 / pwm_freq. But in reality + * it is sys_clk / 256 / (pwm_freq + 1). + */ + data = FIELD_GET(FAN_PWM_FREQ_FREQ, data) + 1; + tmp = DIV_ROUND_CLOSEST(hwmon->clk_rate, 256); + *val = DIV_ROUND_CLOSEST(tmp, data); + + return 0; +} + +static int lan966x_hwmon_read(struct device *dev, enum hwmon_sensor_types type, + u32 attr, int channel, long *val) +{ + + switch (type) { + case hwmon_temp: + return lan966x_hwmon_read_temp(dev, val); + case hwmon_fan: + return lan966x_hwmon_read_fan(dev, val); + case hwmon_pwm: + switch (attr) { + case hwmon_pwm_input: + return lan966x_hwmon_read_pwm(dev, val); + case hwmon_pwm_freq: + return lan966x_hwmon_read_pwm_freq(dev, val); + default: + return -EOPNOTSUPP; + } + default: + return -EOPNOTSUPP; + } +} + +static int lan966x_hwmon_write_pwm(struct device *dev, long val) +{ + struct lan966x_hwmon *hwmon = dev_get_drvdata(dev); + + if (val < 0 || val > 255) + return -EINVAL; + + return regmap_update_bits(hwmon->regmap_fan, FAN_CFG, + FAN_CFG_DUTY_CYCLE, + FIELD_PREP(FAN_CFG_DUTY_CYCLE, val)); +} + +static int lan966x_hwmon_write_pwm_freq(struct device *dev, long val) +{ + struct lan966x_hwmon *hwmon = dev_get_drvdata(dev); + + val = DIV_ROUND_CLOSEST(hwmon->clk_rate, val); + val = DIV_ROUND_CLOSEST(val, 256) - 1; + val = clamp_val(val, 0, FAN_PWM_FREQ_FREQ); + + return regmap_update_bits(hwmon->regmap_fan, FAN_PWM_FREQ, + FAN_PWM_FREQ_FREQ, + FIELD_PREP(FAN_PWM_FREQ_FREQ, val)); +} + +static int lan966x_hwmon_write(struct device *dev, enum hwmon_sensor_types type, + u32 attr, int channel, long val) +{ + switch (type) { + case hwmon_pwm: + switch (attr) { + case hwmon_pwm_input: + return lan966x_hwmon_write_pwm(dev, val); + case hwmon_pwm_freq: + return lan966x_hwmon_write_pwm_freq(dev, val); + default: + return -EOPNOTSUPP; + } + default: + return -EOPNOTSUPP; + } +} + +static umode_t lan966x_hwmon_is_visible(const void *data, + enum hwmon_sensor_types type, + u32 attr, int channel) +{ + umode_t mode = 0; + + switch (type) { + case hwmon_temp: + switch (attr) { + case hwmon_temp_input: + mode = 0444; + break; + default: + break; + } + break; + case hwmon_fan: + switch (attr) { + case hwmon_fan_input: + mode = 0444; + break; + default: + break; + } + break; + case hwmon_pwm: + switch (attr) { + case hwmon_pwm_input: + case hwmon_pwm_freq: + mode = 0644; + break; + default: + break; + } + break; + default: + break; + } + + return mode; +} + + +static const struct hwmon_channel_info *lan966x_hwmon_info[] = { + HWMON_CHANNEL_INFO(chip, HWMON_C_REGISTER_TZ), + HWMON_CHANNEL_INFO(temp, HWMON_T_INPUT), + HWMON_CHANNEL_INFO(fan, HWMON_F_INPUT), + HWMON_CHANNEL_INFO(pwm, HWMON_PWM_INPUT | HWMON_PWM_FREQ), + NULL +}; + +static const struct hwmon_ops lan966x_hwmon_ops = { + .is_visible = lan966x_hwmon_is_visible, + .read = lan966x_hwmon_read, + .write = lan966x_hwmon_write, +}; + +static const struct hwmon_chip_info lan966x_hwmon_chip_info = { + .ops = &lan966x_hwmon_ops, + .info = lan966x_hwmon_info, +}; + +static int lan966x_hwmon_enable(struct lan966x_hwmon *hwmon) +{ + unsigned int mask = SENSOR_CFG_SAMPLE_ENA | + SENSOR_CFG_START_CAPTURE | + SENSOR_CFG_CONTINIOUS_MODE | + SENSOR_CFG_PSAMPLE_ENA; + unsigned int val; + + /* enable continuous mode */ + val = SENSOR_CFG_SAMPLE_ENA | SENSOR_CFG_CONTINIOUS_MODE; + + return regmap_update_bits(hwmon->regmap_pvt, PVT_SENSOR_CFG, + mask, val); +} + +static struct regmap *lan966x_init_regmap(struct platform_device *pdev, + const char *name) +{ + struct regmap_config regmap_config = { + .reg_bits = 32, + .reg_stride = 4, + .val_bits = 32, + }; + void __iomem *base; + + base = devm_platform_ioremap_resource_byname(pdev, name); + if (IS_ERR(base)) + return ERR_CAST(base); + + regmap_config.name = name; + + return devm_regmap_init_mmio(&pdev->dev, base, ®map_config); +} + +static void lan966x_clk_disable(void *data) +{ + struct lan966x_hwmon *hwmon = data; + + clk_disable_unprepare(hwmon->clk); +} + +static int lan966x_clk_enable(struct device *dev, struct lan966x_hwmon *hwmon) +{ + int ret; + + ret = clk_prepare_enable(hwmon->clk); + if (ret) + return ret; + + return devm_add_action_or_reset(dev, lan966x_clk_disable, hwmon); +} + +static int lan966x_hwmon_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct lan966x_hwmon *hwmon; + struct device *hwmon_dev; + int ret; + + hwmon = devm_kzalloc(dev, sizeof(*hwmon), GFP_KERNEL); + if (!hwmon) + return -ENOMEM; + + hwmon->clk = devm_clk_get(dev, NULL); + if (IS_ERR(hwmon->clk)) + return dev_err_probe(dev, PTR_ERR(hwmon->clk), + "failed to get clock\n"); + + ret = lan966x_clk_enable(dev, hwmon); + if (ret) + return dev_err_probe(dev, ret, "failed to enable clock\n"); + + hwmon->clk_rate = clk_get_rate(hwmon->clk); + + hwmon->regmap_pvt = lan966x_init_regmap(pdev, "pvt"); + if (IS_ERR(hwmon->regmap_pvt)) + return dev_err_probe(dev, PTR_ERR(hwmon->regmap_pvt), + "failed to get regmap for PVT registers\n"); + + hwmon->regmap_fan = lan966x_init_regmap(pdev, "fan"); + if (IS_ERR(hwmon->regmap_fan)) + return dev_err_probe(dev, PTR_ERR(hwmon->regmap_fan), + "failed to get regmap for fan registers\n"); + + hwmon_dev = devm_hwmon_device_register_with_info(&pdev->dev, + "lan966x_hwmon", hwmon, + &lan966x_hwmon_chip_info, NULL); + if (IS_ERR(hwmon_dev)) + return dev_err_probe(dev, PTR_ERR(hwmon_dev), + "failed to register hwmon device\n"); + + return lan966x_hwmon_enable(hwmon); +} + +static const struct of_device_id lan966x_hwmon_of_match[] = { + { .compatible = "microchip,lan9668-hwmon" }, + {} +}; +MODULE_DEVICE_TABLE(of, lan966x_hwmon_of_match); + +static struct platform_driver lan966x_hwmon_driver = { + .probe = lan966x_hwmon_probe, + .driver = { + .name = "lan966x-hwmon", + .of_match_table = lan966x_hwmon_of_match, + }, +}; +module_platform_driver(lan966x_hwmon_driver); + +MODULE_DESCRIPTION("LAN966x Hardware Monitoring Driver"); +MODULE_AUTHOR("Michael Walle <michael@xxxxxxxx>"); +MODULE_LICENSE("GPL"); -- 2.30.2
