> -----Original Message-----
> From: Lucas Stach <l.stach@xxxxxxxxxxxxxx>
> Sent: Wednesday, March 2, 2022 5:19 PM
> To: Hongxing Zhu <hongxing.zhu@xxxxxxx>; Laurent Pinchart
> <laurent.pinchart@xxxxxxxxxxxxxxxx>
> Cc: Shawn Guo <shawnguo@xxxxxxxxxx>; Rob Herring <robh+dt@xxxxxxxxxx>;
> Pengutronix Kernel Team <kernel@xxxxxxxxxxxxxx>; dl-linux-imx
> <linux-imx@xxxxxxx>; Marek Vasut <marex@xxxxxxx>;
> devicetree@xxxxxxxxxxxxxxx; linux-arm-kernel@xxxxxxxxxxxxxxxxxxx;
> patchwork-lst@xxxxxxxxxxxxxx
> Subject: Re: [PATCH v3 5/7] arm64: dts: imx8mp: add HSIO power-domains
>
> Hi Richard,
>
> Am Mittwoch, dem 02.03.2022 um 08:47 +0000 schrieb Hongxing Zhu:
> > > -----Original Message-----
> > > From: Lucas Stach <l.stach@xxxxxxxxxxxxxx>
> > > Sent: 2022年3月1日 17:09
> > > To: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> > > Cc: Shawn Guo <shawnguo@xxxxxxxxxx>; Rob Herring
> > > <robh+dt@xxxxxxxxxx>; Pengutronix Kernel Team
> > > <kernel@xxxxxxxxxxxxxx>; dl-linux-imx <linux-imx@xxxxxxx>; Marek
> > > Vasut <marex@xxxxxxx>; devicetree@xxxxxxxxxxxxxxx;
> > > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx;
> > > patchwork-lst@xxxxxxxxxxxxxx
> > > Subject: Re: [PATCH v3 5/7] arm64: dts: imx8mp: add HSIO power-
> > > domains
> > >
> > > Am Dienstag, dem 01.03.2022 um 09:13 +0200 schrieb Laurent
> > > Pinchart:
> > > > Hi Lucas,
> > > >
> > > > Thank you for the patch.
> > > >
> > > > On Mon, Feb 28, 2022 at 09:17:29PM +0100, Lucas Stach wrote:
> > > > > This adds the GPC and HSIO blk-ctrl nodes providing power
> > > > > control for the high-speed (USB and PCIe) IOs.
> > > > >
> > > > > Signed-off-by: Lucas Stach <l.stach@xxxxxxxxxxxxxx>
> > > > > Reviewed-by: Laurent Pinchart
> > > > > <laurent.pinchart@xxxxxxxxxxxxxxxx>
> > Hi Lucas:
> > Thank you for the patch.
> > Based on this V3 serial patch-set. I'm trying to bring up PCIe on
> > i.MX8MP EVK.
> > But I encounter system hang when access the controller's register.
> > Clocks are turned on refer to the /sys/kernel/debug/clk/clk_summary.
> > It seems that the pd of PCIe controller is not up properly.
> > More investigation is still on-going.
>
> Just to check the obvious things: you've put the controller into the
> IMX8MP_HSIOBLK_PD_PCIE and the PHY into IMX8MP_HSIOBLK_PD_PCIE_PHY, right?
>
> If the PHY access works then the power-domains should be powered up properly,
> as the PHY domain is nested inside the HSIO domain where the controller is
> located according to my information. So the most likely reason is still a
> clock path that isn't fully turned on.
Tested USB and it works fine, so
Tested-by: Li Jun <jun.li@xxxxxxx>
>
> Regards,
> Lucas
>
> > BTW, the access of PHY register is successful.
> >
> > Best Regards
> > Richard Zhu
> >
> > > > > ---
> > > > > arch/arm64/boot/dts/freescale/imx8mp.dtsi | 71
> > > > > +++++++++++++++++++++--
> > > > > 1 file changed, 65 insertions(+), 6 deletions(-)
> > > > >
> > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
> > > > > b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
> > > > > index 6b840c05dd77..69e533add539 100644
> > > > > --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
> > > > > +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
> > > > > @@ -4,6 +4,7 @@
> > > > > */
> > > > >
> > > > > #include <dt-bindings/clock/imx8mp-clock.h>
> > > > > +#include <dt-bindings/power/imx8mp-power.h>
> > > > > #include <dt-bindings/gpio/gpio.h>
> > > > > #include <dt-bindings/input/input.h> #include
> > > > > <dt-bindings/interrupt-controller/arm-gic.h>
> > > > > @@ -475,6 +476,44 @@ src: reset-controller@30390000 {
> > > > > interrupts = <GIC_SPI 89
> > > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > > #reset-cells = <1>;
> > > > > };
> > > > > +
> > > > > + gpc: gpc@303a0000 {
> > > > > + compatible = "fsl,imx8mp-gpc";
> > > > > + reg = <0x303a0000 0x1000>;
> > > > > + interrupt-parent = <&gic>;
> > > > > + interrupt-controller;
> > > > > + #interrupt-cells = <3>;
> > > > > +
> > > > > + pgc {
> > > > > + #address-cells = <1>;
> > > > > + #size-cells = <0>;
> > > > > +
> > > > > + pgc_pcie_phy: power-
> > > > > domain@1 {
> > > > > + #power-domain-
> > > > > cells = <0>;
> > > > > + reg =
> > > > > <IMX8MP_POWER_DOMAIN_PCIE_PHY>;
> > > > > + };
> > > > > +
> > > > > + pgc_usb1_phy: power-
> > > > > domain@2 {
> > > > > + #power-domain-
> > > > > cells = <0>;
> > > > > + reg =
> > > > > <IMX8MP_POWER_DOMAIN_USB1_PHY>;
> > > > > + };
> > > > > +
> > > > > + pgc_usb2_phy: power-
> > > > > domain@3 {
> > > > > + #power-domain-
> > > > > cells = <0>;
> > > > > + reg =
> > > > > <IMX8MP_POWER_DOMAIN_USB2_PHY>;
> > > > > + };
> > > > > +
> > > > > + pgc_hsiomix:
> > > > > power-domains@17 {
> > > > > + #power-domain-
> > > > > cells = <0>;
> > > > > + reg =
> > > > > <IMX8MP_POWER_DOMAIN_HSIOMIX>;
> > > > > + clocks = <&clk
> > > > > IMX8MP_CLK_HSIO_AXI>,
> > > > > + <&clk
> > > > > IMX8MP_CLK_HSIO_ROOT>;
> > > > > + assigned-
> > > > > clocks = <&clk
> > > IMX8MP_CLK_HSIO_AXI>;
> > > > > + assigned-
> > > > > clock-parents = <&clk
> > > IMX8MP_SYS_PLL2_500M>;
> > > > > + assigned-
> > > > > clock-rates = <500000000>;
> > > > > + };
> > > > > + };
> > > > > + };
> > > > > };
> > > > >
> > > > > aips2: bus@30400000 {
> > > > > @@ -892,6 +931,28 @@ eqos: ethernet@30bf0000 {
> > > > > };
> > > > > };
> > > > >
> > > > > + aips4 {
> > > >
> > > > I think this should be
> > > >
> > > > aips4: bus@32c00000 {
> > > >
> > > > to match the other buses. Apart from that, the patch looks good,
> > > > my Rb tag still applies.
> > >
> > > Urgh, apparently one shouldn't do those reworks too late in the
> > > evening. :/
> > >
> > > Shawn, would you be willing to fix this up while applying, or should
> > > I resend the series?
> > >
> > > Regards,
> > > Lucas
> > >
> > > >
> > > > > + compatible = "fsl,aips-bus", "simple-
> > > > > bus";
> > > > > + reg = <0x32c00000 0x400000>;
> > > > > + #address-cells = <1>;
> > > > > + #size-cells = <1>;
> > > > > + ranges;
> > > > > +
> > > > > + hsio_blk_ctrl: blk-ctrl@32f10000 {
> > > > > + compatible = "fsl,imx8mp-hsio-
> > > > > blk-ctrl", "syscon";
> > > > > + reg = <0x32f10000 0x24>;
> > > > > + clocks = <&clk
> > > > > IMX8MP_CLK_USB_ROOT>,
> > > > > + <&clk
> > > > > IMX8MP_CLK_PCIE_ROOT>;
> > > > > + clock-names = "usb", "pcie";
> > > > > + power-domains =
> > > > > <&pgc_hsiomix>, <&pgc_hsiomix>,
> > > > > + <&pgc_usb1_phy
> > > > > >, <&pgc_usb2_phy>,
> > > > > + <&pgc_hsiomix>
> > > > > , <&pgc_pcie_phy>;
> > > > > + power-domain-names = "bus",
> > > > > "usb", "usb-phy1",
> > > > > + "usb-
> > > > > phy2", "pcie", "pcie-phy";
> > > > > + #power-domain-cells = <1>;
> > > > > + };
> > > > > + };
> > > > > +
> > > > > gic: interrupt-controller@38800000 {
> > > > > compatible = "arm,gic-v3";
> > > > > reg = <0x38800000 0x10000>,
> > > > > @@ -915,6 +976,7 @@ usb3_phy0: usb-phy@381f0040 {
> > > > > clock-names = "phy";
> > > > > assigned-clocks = <&clk
> > > > > IMX8MP_CLK_USB_PHY_REF>;
> > > > > assigned-clock-parents = <&clk IMX8MP_CLK_24M>;
> > > > > + power-domains = <&hsio_blk_ctrl
> > > IMX8MP_HSIOBLK_PD_USB_PHY1>;
> > > > > #phy-cells = <0>;
> > > > > status = "disabled";
> > > > > };
> > > > > @@ -926,6 +988,7 @@ usb3_0: usb@32f10100 {
> > > > > <&clk IMX8MP_CLK_USB_ROOT>;
> > > > > clock-names = "hsio", "suspend";
> > > > > interrupts = <GIC_SPI 148
> > > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > > + power-domains = <&hsio_blk_ctrl
> > > > > IMX8MP_HSIOBLK_PD_USB>;
> > > > > #address-cells = <1>;
> > > > > #size-cells = <1>;
> > > > > dma-ranges = <0x40000000 0x40000000
> > > > > 0xc0000000>;
> > > @@ -939,9
> > > > > +1002,6 @@ usb_dwc3_0: usb@38100000 {
> > > > > <&clk
> > > > > IMX8MP_CLK_USB_CORE_REF>,
> > > > > <&clk
> > > > > IMX8MP_CLK_USB_ROOT>;
> > > > > clock-names = "bus_early",
> > > > > "ref", "suspend";
> > > > > - assigned-clocks = <&clk
> > > > > IMX8MP_CLK_HSIO_AXI>;
> > > > > - assigned-clock-parents = <&clk
> > > IMX8MP_SYS_PLL2_500M>;
> > > > > - assigned-clock-rates =
> > > > > <500000000>;
> > > > > interrupts = <GIC_SPI 40
> > > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > > phys = <&usb3_phy0>,
> > > > > <&usb3_phy0>;
> > > > > phy-names = "usb2-phy", "usb3- phy"; @@ -957,6
> > > +1017,7 @@
> > > > > usb3_phy1: usb-phy@382f0040 {
> > > > > clock-names = "phy";
> > > > > assigned-clocks = <&clk
> > > > > IMX8MP_CLK_USB_PHY_REF>;
> > > > > assigned-clock-parents = <&clk IMX8MP_CLK_24M>;
> > > > > + power-domains = <&hsio_blk_ctrl
> > > IMX8MP_HSIOBLK_PD_USB_PHY2>;
> > > > > #phy-cells = <0>;
> > > > > };
> > > > >
> > > > > @@ -967,6 +1028,7 @@ usb3_1: usb@32f10108 {
> > > > > <&clk IMX8MP_CLK_USB_ROOT>;
> > > > > clock-names = "hsio", "suspend";
> > > > > interrupts = <GIC_SPI 149
> > > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > > + power-domains = <&hsio_blk_ctrl
> > > > > IMX8MP_HSIOBLK_PD_USB>;
> > > > > #address-cells = <1>;
> > > > > #size-cells = <1>;
> > > > > dma-ranges = <0x40000000 0x40000000
> > > > > 0xc0000000>;
> > > @@ -980,9
> > > > > +1042,6 @@ usb_dwc3_1: usb@38200000 {
> > > > > <&clk
> > > > > IMX8MP_CLK_USB_CORE_REF>,
> > > > > <&clk
> > > > > IMX8MP_CLK_USB_ROOT>;
> > > > > clock-names = "bus_early",
> > > > > "ref", "suspend";
> > > > > - assigned-clocks = <&clk
> > > > > IMX8MP_CLK_HSIO_AXI>;
> > > > > - assigned-clock-parents = <&clk
> > > IMX8MP_SYS_PLL2_500M>;
> > > > > - assigned-clock-rates =
> > > > > <500000000>;
> > > > > interrupts = <GIC_SPI 41
> > > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > > phys = <&usb3_phy1>,
> > > > > <&usb3_phy1>;
> > > > > phy-names = "usb2-phy", "usb3- phy";
> > > >
> > >
> >
>
