From: Dmitry Antipov <dmanti@xxxxxxxxxxxxx> Documentation describes the required and optional properties for implementing Device Tree for a Microsoft G6 Touch Digitizer that supports HID over SPI Protocol 1.0 specification. Signed-off-by: Dmitry Antipov <dmanti@xxxxxxxxxxxxx> --- .../input/microsoft,g6-touch-digitizer.yaml | 105 ++++++++++++++++++ 1 file changed, 105 insertions(+) create mode 100644 Documentation/devicetree/bindings/input/microsoft,g6-touch-digitizer.yaml diff --git a/Documentation/devicetree/bindings/input/microsoft,g6-touch-digitizer.yaml b/Documentation/devicetree/bindings/input/microsoft,g6-touch-digitizer.yaml new file mode 100644 index 000000000000..e516717527e9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/microsoft,g6-touch-digitizer.yaml @@ -0,0 +1,105 @@ +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/microsoft,g6-touch-digitizer.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microsoft G6 Touch Digitizer + +maintainers: + - Dmitry Antipov <dmanti@xxxxxxxxxxxxx> + +description: | + Microsoft G6 touch digitizer is a HID over SPI device supporting HID Over SPI + Protocol Specification 1.0, available at + https://www.microsoft.com/en-us/download/details.aspx?id=103325. + +properties: + compatible: + oneOf: + - const: microsoft,g6-touch-digitizer + - items: + - const: microsoft,g6-touch-digitizer + - const: hid-over-spi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + description: + GPIO specifier for the digitizer's reset pin (active low). The line must + be flagged with GPIO_ACTIVE_LOW. + + vdd-supply: + description: + Regulator for the VDD supply voltage. + + input-report-header-address: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + This property and the rest are described in HID Over SPI Protocol Spec 1.0 + + input-report-body-address: + $ref: /schemas/types.yaml#/definitions/uint32 + + output-report-address: + $ref: /schemas/types.yaml#/definitions/uint32 + + read-opcode: + $ref: /schemas/types.yaml#/definitions/uint32 + + write-opcode: + $ref: /schemas/types.yaml#/definitions/uint32 + + hid-over-spi-flags: + $ref: /schemas/types.yaml#/definitions/uint32 + + post-power-on-delay-ms: + description: + Optional time in ms required by the device after enabling its regulators + or powering it on, before it is ready for communication. + + minimal-reset-delay-ms: + description: + Optional minimum amount of time in ms that device needs to be in reset + state for the reset to take effect. + +required: + - compatible + - interrupts + - reset-gpios + - vdd-supply + - input-report-header-address + - input-report-body-address + - output-report-address + - read-opcode + - write-opcode + - hid-over-spi-flags + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + spi-hid-dev0 { + compatible = "microsoft,g6-touch-digitizer", "hid-over-spi"; + reg = <0>; + interrupts-extended = <&gpio 42 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>; + vdd-supply = <&pm8350c_l3>; + pinctrl-names = "default"; + pinctrl-0 = <&ts_d6_reset_assert &ts_d6_int_bias>; + input-report-header-address = <0x1000>; + input-report-body-address = <0x1004>; + output-report-address = <0x2000>; + read-opcode = <0x0b>; + write-opcode = <0x02>; + hid-over-spi-flags = <0x00>; + post-power-on-delay-ms = <5>; + minimal-reset-delay-ms = <5>; + }; -- 2.25.1
