RZ/G2LC SoM uses DIP-SWitch SW1 for various pin multiplexing functions.
This patch describes DIP-SWitch SW1 settings on SoM and adds the
corresponding macros for enabling pinmux functionality on RZ/G2LC
SMARC EVK.
Signed-off-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
---
v2->v3: No change
v1->v2: No change
---
.../boot/dts/renesas/r9a07g044c2-smarc.dts | 4 +--
arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi | 36 +++++++++++++++++++
2 files changed, 37 insertions(+), 3 deletions(-)
create mode 100644 arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi
diff --git a/arch/arm64/boot/dts/renesas/r9a07g044c2-smarc.dts b/arch/arm64/boot/dts/renesas/r9a07g044c2-smarc.dts
index af84fd6c8a81..50abdabc374a 100644
--- a/arch/arm64/boot/dts/renesas/r9a07g044c2-smarc.dts
+++ b/arch/arm64/boot/dts/renesas/r9a07g044c2-smarc.dts
@@ -7,9 +7,7 @@
/dts-v1/;
#include "r9a07g044c2.dtsi"
-#include "rzg2lc-smarc-som.dtsi"
-#include "rzg2lc-smarc-pinfunction.dtsi"
-#include "rz-smarc-common.dtsi"
+#include "rzg2lc-smarc.dtsi"
/ {
model = "Renesas SMARC EVK based on r9a07g044c2";
diff --git a/arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi b/arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi
new file mode 100644
index 000000000000..ca5ca7ce6692
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2LC SMARC EVK parts
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+/*
+ * DIP-Switch SW1 setting on SoM
+ * 1 : High; 0: Low
+ * SW1-2 : SW_SD0_DEV_SEL (1: eMMC; 0: uSD)
+ * SW1-3 : SW_SCIF_CAN (1: CAN1; 0: SCIF1)
+ * SW1-4 : SW_RSPI_CAN (1: CAN1; 0: RSPI1)
+ * SW1-5 : SW_I2S0_I2S1 (1: I2S2 (HDMI audio); 0: I2S0)
+ * Please change below macros according to SW1 setting
+ */
+
+#define SW_SCIF_CAN 0
+#if (SW_SCIF_CAN)
+/* Due to HW routing, SW_RSPI_CAN is always 0 when SW_SCIF_CAN is set to 1 */
+#define SW_RSPI_CAN 0
+#else
+/* Please set SW_RSPI_CAN. Default value is 1 */
+#define SW_RSPI_CAN 1
+#endif
+
+#if (SW_SCIF_CAN & SW_RSPI_CAN)
+#error "Can not set 1 to both SW_SCIF_CAN and SW_RSPI_CAN due to HW routing"
+#endif
+
+#include "rzg2lc-smarc-som.dtsi"
+#include "rzg2lc-smarc-pinfunction.dtsi"
+#include "rz-smarc-common.dtsi"
--
2.17.1
