Re: [PATCH dt + pci 1/2] dt-bindings: Add 'slot-power-limit-milliwatt' PCIe port property

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Jan 5, 2022 at 8:14 AM Marek Behún <kabel@xxxxxxxxxx> wrote:
>
> On Fri, 12 Nov 2021 09:25:20 -0600
> Rob Herring <robh@xxxxxxxxxx> wrote:
>
> > On Sun, Oct 31, 2021 at 04:07:05PM +0100, Marek Behún wrote:
> > > From: Pali Rohár <pali@xxxxxxxxxx>
> > >
> > > This property specifies slot power limit in mW unit. It is a form-factor
> > > and board specific value and must be initialized by hardware.
> > >
> > > Some PCIe controllers delegate this work to software to allow hardware
> > > flexibility and therefore this property basically specifies what should
> > > host bridge program into PCIe Slot Capabilities registers.
> > >
> > > The property needs to be specified in mW unit instead of the special format
> > > defined by Slot Capabilities (which encodes scaling factor or different
> > > unit). Host drivers should convert the value from mW to needed format.
> > >
> > > Signed-off-by: Pali Rohár <pali@xxxxxxxxxx>
> > > Signed-off-by: Marek Behún <kabel@xxxxxxxxxx>
> > > ---
> > >  Documentation/devicetree/bindings/pci/pci.txt | 6 ++++++
> > >  1 file changed, 6 insertions(+)
> > >
> > > diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt
> > > index 6a8f2874a24d..7296d599c5ac 100644
> > > --- a/Documentation/devicetree/bindings/pci/pci.txt
> > > +++ b/Documentation/devicetree/bindings/pci/pci.txt
> > > @@ -32,6 +32,12 @@ driver implementation may support the following properties:
> > >     root port to downstream device and host bridge drivers can do programming
> > >     which depends on CLKREQ signal existence. For example, programming root port
> > >     not to advertise ASPM L1 Sub-States support if there is no CLKREQ signal.
> > > +- slot-power-limit-miliwatt:
> >
> > Typo.
> >
> > But we shouldn't be adding to pci.txt. This needs to go in the
> > schema[1]. Patch to devicetree-spec list or GH PR is fine.
>
> Hello Rob,
>
> Pali's PR draft https://github.com/devicetree-org/dt-schema/pull/64
> looks like it's going to take some time to work out.
>
> In the meantime, is it possible to somehow get the
> slot-power-limit-milliwatt property merged into pci.txt so that we can start
> putting it into existing device-trees?
>
> Or would it break dt_bindings_check if it isn't put into dt-schema's
> pci-bus.yaml?
>
> Or should we simply put it into current version of pci-bus.yaml and
> work out the split proposed by Pali's PR afterwards?

In the existing pci-bus.yaml is fine.

Rob




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux