On Sun, Nov 28, 2021 at 4:50 AM Adam Ford <aford173@xxxxxxxxx> wrote:
>
> Most of the blk-ctrl reset bits are found in one register, however
> there are two bits in offset 8 for pulling the MIPI DPHY out of reset
> and one of them needs to be set when IMX8MM_DISPBLK_PD_MIPI_CSI is brought
> out of reset or the MIPI_CSI hangs.
>
> Since MIPI_DSI is impacted, add the additional one for MIPI_DSI too.
>
> Fixes: 926e57c065df ("soc: imx: imx8m-blk-ctrl: add DISP blk-ctrl")
> Signed-off-by: Adam Ford <aford173@xxxxxxxxx>
> Reviewed-by: Fabio Estevam <festevam@xxxxxxxxx>
> Reviewed-by: Lucas Stach <l.stach@xxxxxxxxxxxxxx>
> ---
> V3: Split the mipi_phy_rst_mask for CSI and DSI into their respective domains.
>
> V2: Make a note that the extra register is only for Mini/Nano DISPLAY_BLK_CTRL
> Rename the new register to mipi_phy_rst_mask
> Encapsulate the edits to this register with an if-statement
>
> drivers/soc/imx/imx8m-blk-ctrl.c | 19 +++++++++++++++++++
> 1 file changed, 19 insertions(+)
>
> diff --git a/drivers/soc/imx/imx8m-blk-ctrl.c b/drivers/soc/imx/imx8m-blk-ctrl.c
> index 519b3651d1d9..c2f076b56e24 100644
> --- a/drivers/soc/imx/imx8m-blk-ctrl.c
> +++ b/drivers/soc/imx/imx8m-blk-ctrl.c
> @@ -17,6 +17,7 @@
>
> #define BLK_SFT_RSTN 0x0
> #define BLK_CLK_EN 0x4
> +#define BLK_MIPI_RESET_DIV 0x8 /* Mini/Nano DISPLAY_BLK_CTRL only */
>
> struct imx8m_blk_ctrl_domain;
>
> @@ -36,6 +37,15 @@ struct imx8m_blk_ctrl_domain_data {
> const char *gpc_name;
> u32 rst_mask;
> u32 clk_mask;
> +
> + /*
> + * i.MX8M Mini and Nano have a third DISPLAY_BLK_CTRL register
> + * which is used to control the reset for the MIPI Phy.
> + * Since it's only present in certain circumstances,
> + * an if-statement should be used before setting and clearing this
> + * register.
> + */
> + u32 mipi_phy_rst_mask;
> };
>
> #define DOMAIN_MAX_CLKS 3
> @@ -78,6 +88,8 @@ static int imx8m_blk_ctrl_power_on(struct generic_pm_domain *genpd)
>
> /* put devices into reset */
> regmap_clear_bits(bc->regmap, BLK_SFT_RSTN, data->rst_mask);
> + if (data->mipi_phy_rst_mask)
> + regmap_clear_bits(bc->regmap, BLK_MIPI_RESET_DIV, data->mipi_phy_rst_mask);
>
> /* enable upstream and blk-ctrl clocks to allow reset to propagate */
> ret = clk_bulk_prepare_enable(data->num_clks, domain->clks);
> @@ -99,6 +111,8 @@ static int imx8m_blk_ctrl_power_on(struct generic_pm_domain *genpd)
>
> /* release reset */
> regmap_set_bits(bc->regmap, BLK_SFT_RSTN, data->rst_mask);
> + if (data->mipi_phy_rst_mask)
> + regmap_set_bits(bc->regmap, BLK_MIPI_RESET_DIV, data->mipi_phy_rst_mask);
>
> /* disable upstream clocks */
> clk_bulk_disable_unprepare(data->num_clks, domain->clks);
> @@ -120,6 +134,9 @@ static int imx8m_blk_ctrl_power_off(struct generic_pm_domain *genpd)
> struct imx8m_blk_ctrl *bc = domain->bc;
>
> /* put devices into reset and disable clocks */
> + if (data->mipi_phy_rst_mask)
> + regmap_clear_bits(bc->regmap, BLK_MIPI_RESET_DIV, data->mipi_phy_rst_mask);
> +
> regmap_clear_bits(bc->regmap, BLK_SFT_RSTN, data->rst_mask);
> regmap_clear_bits(bc->regmap, BLK_CLK_EN, data->clk_mask);
>
> @@ -480,6 +497,7 @@ static const struct imx8m_blk_ctrl_domain_data imx8mm_disp_blk_ctl_domain_data[]
> .gpc_name = "mipi-dsi",
> .rst_mask = BIT(5),
> .clk_mask = BIT(8) | BIT(9),
> + .mipi_phy_rst_mask = BIT(17),
> },
> [IMX8MM_DISPBLK_PD_MIPI_CSI] = {
> .name = "dispblk-mipi-csi",
> @@ -488,6 +506,7 @@ static const struct imx8m_blk_ctrl_domain_data imx8mm_disp_blk_ctl_domain_data[]
> .gpc_name = "mipi-csi",
> .rst_mask = BIT(3) | BIT(4),
> .clk_mask = BIT(10) | BIT(11),
> + .mipi_phy_rst_mask = BIT(16),
> },
> };
>
> --
> 2.32.0
>
Adam,
Thanks - this is working on my hardware as well and I can display what
is captured on an imx219 to a dsi display.
Tested by: Tim Harvey <tharvey@xxxxxxxxxxxxx> (tested on
imx8mm-venice-gw73xx-0x with imx219 support added)
Tim
