Hi Maxime,
On 11/19/21 2:28 AM, Maxime Ripard wrote:
> Hi,
>
> On Thu, Nov 18, 2021 at 11:40:43PM -0600, Samuel Holland wrote:
>> +static const struct sun50i_r329_ledc_timing sun50i_r329_ledc_default_timing = {
>> + .t0h_ns = 336,
>> + .t0l_ns = 840,
>> + .t1h_ns = 882,
>> + .t1l_ns = 294,
>> + .treset_ns = 300000,
>> +};
>
> This should be mentioned in the binding as well (using the default keyword)
Ok, I'll do this for v4.
>> +static int sun50i_r329_ledc_parse_timing(const struct device_node *np,
>> + struct sun50i_r329_ledc *priv)
>> +{
>> + struct sun50i_r329_ledc_timing *timing = &priv->timing;
>> +
>> + *timing = sun50i_r329_ledc_default_timing;
>> +
>> + of_property_read_u32(np, "allwinner,t0h-ns", &timing->t0h_ns);
>> + of_property_read_u32(np, "allwinner,t0l-ns", &timing->t0l_ns);
>> + of_property_read_u32(np, "allwinner,t1h-ns", &timing->t1h_ns);
>> + of_property_read_u32(np, "allwinner,t1l-ns", &timing->t1l_ns);
>> + of_property_read_u32(np, "allwinner,treset-ns", &timing->treset_ns);
>> +
>> + return 0;
>> +}
>> +
>> +static void sun50i_r329_ledc_set_timing(struct sun50i_r329_ledc *priv)
>> +{
>> + const struct sun50i_r329_ledc_timing *timing = &priv->timing;
>> + unsigned long mod_freq = clk_get_rate(priv->mod_clk);
>> + u32 cycle_ns = NSEC_PER_SEC / mod_freq;
>> + u32 val;
>> +
>> + val = (timing->t1h_ns / cycle_ns) << 21 |
>> + (timing->t1l_ns / cycle_ns) << 16 |
>> + (timing->t0h_ns / cycle_ns) << 6 |
>> + (timing->t0l_ns / cycle_ns);
>> + writel(val, priv->base + LEDC_T01_TIMING_CTRL_REG);
>> +
>> + val = (timing->treset_ns / cycle_ns) << 16 |
>> + (priv->num_leds - 1);
>> + writel(val, priv->base + LEDC_RESET_TIMING_CTRL_REG);
>> +}
>> +
>> +static int sun50i_r329_ledc_resume(struct device *dev)
>> +{
>> + struct sun50i_r329_ledc *priv = dev_get_drvdata(dev);
>> + u32 val;
>> + int ret;
>> +
>> + ret = reset_control_deassert(priv->reset);
>> + if (ret)
>> + return ret;
>> +
>> + ret = clk_prepare_enable(priv->bus_clk);
>> + if (ret)
>> + goto err_assert_reset;
>> +
>> + ret = clk_prepare_enable(priv->mod_clk);
>> + if (ret)
>> + goto err_disable_bus_clk;
>> +
>> + sun50i_r329_ledc_set_format(priv);
>> + sun50i_r329_ledc_set_timing(priv);
>> +
>> + /* The trigger level must be at least the burst length. */
>> + val = readl(priv->base + LEDC_DMA_CTRL_REG);
>> + val &= ~LEDC_DMA_CTRL_REG_FIFO_TRIG_LEVEL;
>> + val |= LEDC_FIFO_DEPTH / 2;
>> + writel(val, priv->base + LEDC_DMA_CTRL_REG);
>> +
>> + val = LEDC_INT_CTRL_REG_GLOBAL_INT_EN |
>> + LEDC_INT_CTRL_REG_TRANS_FINISH_INT_EN;
>> + writel(val, priv->base + LEDC_INT_CTRL_REG);
>> +
>> + return 0;
>> +
>> +err_disable_bus_clk:
>> + clk_disable_unprepare(priv->bus_clk);
>> +err_assert_reset:
>> + reset_control_assert(priv->reset);
>> +
>> + return ret;
>> +}
>> +
>> +static int sun50i_r329_ledc_suspend(struct device *dev)
>> +{
>> + struct sun50i_r329_ledc *priv = dev_get_drvdata(dev);
>> +
>> + clk_disable_unprepare(priv->mod_clk);
>> + clk_disable_unprepare(priv->bus_clk);
>> + reset_control_assert(priv->reset);
>> +
>> + return 0;
>> +}
>> +
>> +static void sun50i_r329_ledc_dma_cleanup(void *data)
>> +{
>> + struct sun50i_r329_ledc *priv = data;
>> + struct device *dma_dev = dmaengine_get_dma_device(priv->dma_chan);
>> +
>> + if (priv->buffer)
>> + dma_free_wc(dma_dev, LEDS_TO_BYTES(priv->num_leds),
>> + priv->buffer, priv->dma_handle);
>> + dma_release_channel(priv->dma_chan);
>> +}
>> +
>> +static int sun50i_r329_ledc_probe(struct platform_device *pdev)
>> +{
>> + const struct device_node *np = pdev->dev.of_node;
>> + struct dma_slave_config dma_cfg = {};
>> + struct led_init_data init_data = {};
>> + struct device *dev = &pdev->dev;
>> + struct device_node *child;
>> + struct sun50i_r329_ledc *priv;
>> + struct resource *mem;
>> + int count, irq, ret;
>> +
>> + count = of_get_available_child_count(np);
>> + if (!count)
>> + return -ENODEV;
>> + if (count > LEDC_MAX_LEDS) {
>> + dev_err(dev, "Too many LEDs! (max is %d)\n", LEDC_MAX_LEDS);
>> + return -EINVAL;
>> + }
>> +
>> + priv = devm_kzalloc(dev, struct_size(priv, leds, count), GFP_KERNEL);
>> + if (!priv)
>> + return -ENOMEM;
>> +
>> + priv->dev = dev;
>> + priv->num_leds = count;
>> + spin_lock_init(&priv->lock);
>> + dev_set_drvdata(dev, priv);
>> +
>> + ret = sun50i_r329_ledc_parse_format(np, priv);
>> + if (ret)
>> + return ret;
>> +
>> + ret = sun50i_r329_ledc_parse_timing(np, priv);
>> + if (ret)
>> + return ret;
>> +
>> + priv->base = devm_platform_get_and_ioremap_resource(pdev, 0, &mem);
>> + if (IS_ERR(priv->base))
>> + return PTR_ERR(priv->base);
>> +
>> + priv->bus_clk = devm_clk_get(dev, "bus");
>> + if (IS_ERR(priv->bus_clk))
>> + return PTR_ERR(priv->bus_clk);
>> +
>> + priv->mod_clk = devm_clk_get(dev, "mod");
>> + if (IS_ERR(priv->mod_clk))
>> + return PTR_ERR(priv->mod_clk);
>> +
>> + priv->reset = devm_reset_control_get_exclusive(dev, NULL);
>> + if (IS_ERR(priv->reset))
>> + return PTR_ERR(priv->reset);
>> +
>> + priv->dma_chan = dma_request_chan(dev, "tx");
>> + if (IS_ERR(priv->dma_chan))
>> + return PTR_ERR(priv->dma_chan);
>> +
>> + ret = devm_add_action_or_reset(dev, sun50i_r329_ledc_dma_cleanup, priv);
>> + if (ret)
>> + return ret;
>> +
>> + dma_cfg.dst_addr = mem->start + LEDC_DATA_REG;
>> + dma_cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
>> + dma_cfg.dst_maxburst = LEDC_FIFO_DEPTH / 2;
>> + ret = dmaengine_slave_config(priv->dma_chan, &dma_cfg);
>> + if (ret)
>> + return ret;
>> +
>> + priv->buffer = dma_alloc_wc(dmaengine_get_dma_device(priv->dma_chan),
>> + LEDS_TO_BYTES(priv->num_leds),
>> + &priv->dma_handle, GFP_KERNEL);
>> + if (!priv->buffer)
>> + return -ENOMEM;
>> +
>> + irq = platform_get_irq(pdev, 0);
>> + if (irq < 0)
>> + return irq;
>> +
>> + ret = devm_request_irq(dev, irq, sun50i_r329_ledc_irq,
>> + 0, dev_name(dev), priv);
>> + if (ret)
>> + return ret;
>> +
>> + ret = sun50i_r329_ledc_resume(dev);
>> + if (ret)
>> + return ret;
>
> You seem to fill the runtime_pm hooks, but only call them directly and
> never enable runtime_pm on that device, is that intentional?
Yes. I did not want to delay the initial version by adding runtime PM
(and debugging the refcounts) when the driver already works now.
However, I had runtime/system PM in mind while writing the driver.
If you think it is too confusing, I could rename the functions to
something like sun50i_r329_ledc_hw_init / sun50i_r329_ledc_hw_exit.
Regards,
Samuel
