On Thu, 28 Oct 2021 12:18:36 +0200 Andrea Merello <andrea.merello@xxxxxxxxx> wrote: > This patch adds ABI documentation for bno055 driver private sysfs > attributes. Hohum. As normal I dislike custom attributes but reality is these don't map to anything 'standard' and I don't want them getting adopted in places where the 'standard' approach works. So thinking a bit more on this, I wonder if we can fit it into standard ABI. We can't use the normal range specification method of _scale because it's internal to the device and the output reading is unaffected. The range specification via _raw_available would let us know the range, but it is not writeable so.. A control that changes the internal scaling of the sensor in a fashion that is not visible to the outside world maps to calibscale. Whilst that was intended for little tweaks to the input signal (often front end amplifier gain tweak) it works here. It doesn't map through to anything userspace is expected to apply. That combined with _raw_available to let us know what the result is should work? What do you think of that approach? It's obviously a little more complex to handle in the driver, but it does map to existing ABI and avoids custom attributes etc. > > Signed-off-by: Andrea Merello <andrea.merello@xxxxxx> > --- > .../ABI/testing/sysfs-bus-iio-bno055 | 84 +++++++++++++++++++ > 1 file changed, 84 insertions(+) > create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-bno055 > > diff --git a/Documentation/ABI/testing/sysfs-bus-iio-bno055 b/Documentation/ABI/testing/sysfs-bus-iio-bno055 > new file mode 100644 > index 000000000000..930a70c5a858 > --- /dev/null > +++ b/Documentation/ABI/testing/sysfs-bus-iio-bno055 > @@ -0,0 +1,84 @@ > +What: /sys/bus/iio/devices/iio:deviceX/in_accel_range > +KernelVersion: 5.15 > +Contact: linux-iio@xxxxxxxxxxxxxxx > +Description: > + Range for acceleration readings in G. Note that this does not > + affects the scale (which should be used when changing the > + maximum and minimum readable value affects also the reading > + scaling factor). Having this in G but the sensor output in m/s^2 seems inconsistent. > + > +What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_range > +KernelVersion: 5.15 > +Contact: linux-iio@xxxxxxxxxxxxxxx > +Description: > + Range for angular velocity readings in dps. Note that this does > + not affects the scale (which should be used when changing the > + maximum and minimum readable value affects also the reading > + scaling factor). Again, units need to match or this is going to be really confusing. > + > +What: /sys/bus/iio/devices/iio:deviceX/in_accel_range_available > +KernelVersion: 5.15 > +Contact: linux-iio@xxxxxxxxxxxxxxx > +Description: > + List of allowed values for in_accel_range attribute > + > +What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_range_available > +KernelVersion: 5.15 > +Contact: linux-iio@xxxxxxxxxxxxxxx > +Description: > + List of allowed values for in_anglvel_range attribute > + > +What: /sys/bus/iio/devices/iio:deviceX/fast_magnetometer_calibration_enable > +KernelVersion: 5.15 > +Contact: linux-iio@xxxxxxxxxxxxxxx > +Description: > + Can be 1 or 0. Enables/disables the "Fast Magnetometer > + Calibration" HW function. Naming needs to be consistent with the ABI. This is a channel type specific function and to match existing calibration related ABI naming it would be. in_magn_calibration_fast_enable Some of the others need renaming in a similar way. > + > +What: /sys/bus/iio/devices/iio:deviceX/fusion_enable > +KernelVersion: 5.15 > +Contact: linux-iio@xxxxxxxxxxxxxxx > +Description: > + Can be 1 or 0. Enables/disables the "sensor fusion" (a.k.a. > + NDOF) HW function. > + > +What: /sys/bus/iio/devices/iio:deviceX/in_calibration_data > +KernelVersion: 5.15 > +Contact: linux-iio@xxxxxxxxxxxxxxx > +Description: > + Reports the binary calibration data blob for the IMU sensors. Why in_ ? What channels does this apply to? > + > +What: /sys/bus/iio/devices/iio:deviceX/in_autocalibration_status_accel > +KernelVersion: 5.15 > +Contact: linux-iio@xxxxxxxxxxxxxxx > +Description: > + Can be "Idle", "Bad", "Barely enough", "Fair", or "Good". > + Report the autocalibration status for the accelerometer sensor. For interfaces that really don't have any chance of generalising this one is terrible. Any hope at all of mapping this to something numeric? in_accel_calibration_auto_status > + > +What: /sys/bus/iio/devices/iio:deviceX/in_autocalibration_status_gyro > +KernelVersion: 5.15 > +Contact: linux-iio@xxxxxxxxxxxxxxx > +Description: > + Can be "Idle", "Bad", "Barely enough", "Fair", or "Good". > + Reports the autocalibration status for the gyroscope sensor. in_angvel_calibration_auto_status etc. > + > +What: /sys/bus/iio/devices/iio:deviceX/in_autocalibration_status_magn > +KernelVersion: 5.15 > +Contact: linux-iio@xxxxxxxxxxxxxxx > +Description: > + Can be "Idle", "Bad", "Barely enough", "Fair", or "Good". > + Reports the autocalibration status for the magnetometer sensor. > + > +What: /sys/bus/iio/devices/iio:deviceX/in_autocalibration_status_sys > +KernelVersion: 5.15 > +Contact: linux-iio@xxxxxxxxxxxxxxx > +Description: > + Can be "Idle", "Bad", "Barely enough", "Fair", or "Good". > + Reports the status for the IMU overall autocalibration. > + > +What: /sys/bus/iio/devices/iio:deviceX/unique_id Hmm. So normally we just dump these in the kernel log. I guess you need it here to associate a calibration blob with a particular sensor? We could put it in label, but that would stop us using that for things like positioning of the sensor. So perhaps this is something that we should add to the main ABI doc. Probably as serial_number rather than unique ID though. > +KernelVersion: 5.15 > +Contact: linux-iio@xxxxxxxxxxxxxxx > +Description: > + 16-bytes, 2-digits-per-byte, HEX-string representing the sensor > + unique ID number.
