On 07/10/2021 20:48, Prasad Malisetty wrote:
Add PCIe controller and PHY nodes for sc7280 SOC.
Signed-off-by: Prasad Malisetty <pmaliset@xxxxxxxxxxxxxx>
Reviewed-by: Stephen Boyd <swboyd@xxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sc7280.dtsi | 118 +++++++++++++++++++++++++++++++++++
1 file changed, 118 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 39635da..cde814f 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -1563,6 +1563,117 @@
qcom,bcm-voters = <&apps_bcm_voter>;
};
+ pcie1: pci@1c08000 {
+ compatible = "qcom,pcie-sc7280";
+ reg = <0 0x01c08000 0 0x3000>,
+ <0 0x40000000 0 0xf1d>,
+ <0 0x40000f20 0 0xa8>,
+ <0 0x40001000 0 0x1000>,
+ <0 0x40100000 0 0x100000>;
+
+ reg-names = "parf", "dbi", "elbi", "atu", "config";
+ device_type = "pci";
+ linux,pci-domain = <1>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
+ <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
+
+ interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
+ <&gcc GCC_PCIE_1_PIPE_CLK_SRC>,
+ <&pcie1_lane 0>,
This should be just <&pcie1_lane>, as the phy doesn't have clock cells.
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_PCIE_1_AUX_CLK>,
+ <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+ <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+ <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
+ <&gcc GCC_DDRSS_PCIE_SF_CLK>;
+
+ clock-names = "pipe",
+ "pipe_mux",
+ "phy_pipe",
+ "ref",
+ "aux",
+ "cfg",
+ "bus_master",
+ "bus_slave",
+ "slave_q2a",
+ "tbu",
+ "ddrss_sf_tbu";
+
+ assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ resets = <&gcc GCC_PCIE_1_BCR>;
+ reset-names = "pci";
+
+ power-domains = <&gcc GCC_PCIE_1_GDSC>;
+
+ phys = <&pcie1_lane>;
+ phy-names = "pciephy";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie1_clkreq_n>;
+
+ iommus = <&apps_smmu 0x1c80 0x1>;
+
+ iommu-map = <0x0 &apps_smmu 0x1c80 0x1>,
+ <0x100 &apps_smmu 0x1c81 0x1>;
+
+ status = "disabled";
+ };
+
+ pcie1_phy: phy@1c0e000 {
+ compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy";
+ reg = <0 0x01c0e000 0 0x1c0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+ <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_CLKREF_EN>,
+ <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+ resets = <&gcc GCC_PCIE_1_PHY_BCR>;
+ reset-names = "phy";
+
+ assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
+ assigned-clock-rates = <100000000>;
+
+ status = "disabled";
+
+ pcie1_lane: lanes@1c0e200 {
+ reg = <0 0x01c0e200 0 0x170>,
+ <0 0x01c0e400 0 0x200>,
+ <0 0x01c0ea00 0 0x1f0>,
+ <0 0x01c0e600 0 0x170>,
+ <0 0x01c0e800 0 0x200>,
+ <0 0x01c0ee00 0 0xf4>;
+ clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
+ clock-names = "pipe0";
+
+ #phy-cells = <0>;
+ #clock-cells = <1>;
+ clock-output-names = "pcie_1_pipe_clk";
+ };
+ };
+
ipa: ipa@1e40000 {
compatible = "qcom,sc7280-ipa";
@@ -2676,6 +2787,13 @@
gpio-ranges = <&tlmm 0 0 175>;
wakeup-parent = <&pdc>;
+ pcie1_clkreq_n: pcie1-clkreq-n {
+ pins = "gpio79";
+ function = "pcie1_clkreqn";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
qspi_clk: qspi-clk {
pins = "gpio14";
function = "qspi_clk";
--
With best wishes
Dmitry
