Il 28/04/21 08:54, Roger Lu ha scritto:
add compitable/reg/irq/clock/efuse/reset setting in svs node
Signed-off-by: Roger Lu <roger.lu@xxxxxxxxxxxx>
---
arch/arm64/boot/dts/mediatek/mt8192.dtsi | 34 ++++++++++++++++++++++++
1 file changed, 34 insertions(+)
Hello Roger,
thanks for this series! However, there is an issue with this patch:
diff --git a/arch/arm64/boot/dts/mediatek/mt8192.dtsi b/arch/arm64/boot/dts/mediatek/mt8192.dtsi
index fe24cc66ff7a..e9816a56d87b 100644
--- a/arch/arm64/boot/dts/mediatek/mt8192.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8192.dtsi
@@ -270,6 +270,14 @@
compatible = "mediatek,mt8192-infracfg", "syscon";
reg = <0 0x10001000 0 0x1000>;
#clock-cells = <1>;
+
+ infracfg_rst: reset-controller {
+ compatible = "mediatek,infra-reset", "ti,syscon-reset";
+ #reset-cells = <1>;
+ ti,reset-bits = <
+ 0x150 5 0x154 5 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE) /* 0: svs */
You are using macros here, which are defined in dt-bindings/reset/ti-syscon.h
hovever, you are not including this header in this devicetree, so it's not
compiling.
Please fix it.
+ >;
+ };
};
pericfg: syscon@10003000 {
@@ -564,6 +572,20 @@
status = "disabled";
};
+ svs: svs@1100b000 {
+ compatible = "mediatek,mt8192-svs";
+ reg = <0 0x1100b000 0 0x1000>;
+ interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&infracfg CLK_INFRA_THERM>;
+ clock-names = "main";
+ nvmem-cells = <&svs_calibration>,
+ <&lvts_e_data1>;
+ nvmem-cell-names = "svs-calibration-data",
+ "t-calibration-data";
+ resets = <&infracfg_rst 0>;
+ reset-names = "svs_rst";
+ };
+
spi1: spi@11010000 {
compatible = "mediatek,mt8192-spi",
"mediatek,mt6765-spi";
@@ -681,6 +703,18 @@
#clock-cells = <1>;
};
+ efuse: efuse@11c10000 {
+ compatible = "mediatek,efuse";
+ reg = <0 0x11c10000 0 0x1000>;
+
arch/arm64/boot/dts/mediatek/mt8192.dtsi:510.5-24: Warning (reg_format):
/soc/efuse@11c10000/data1:reg: property has invalid length (8 bytes)
(#address-cells == 2, #size-cells == 1)
arch/arm64/boot/dts/mediatek/mt8192.dtsi:513.5-24: Warning (reg_format):
/soc/efuse@11c10000/calib@580:reg: property has invalid length (8 bytes)
(#address-cells == 2, #size-cells == 1)
In short, you should add here:
#address-cells = <1>;
#size-cells = <1>;
+ lvts_e_data1: data1 {
+ reg = <0x1C0 0x58>;
+ };
+ svs_calibration: calib@580 {
+ reg = <0x580 0x68>;
+ };
+ };
+
i2c3: i2c3@11cb0000 {
compatible = "mediatek,mt8192-i2c";
reg = <0 0x11cb0000 0 0x1000>,
Regards,
- Angelo
