The CN9130-CRB boards have a MV88E6393X switch connected to eth0. Add
the necessary dts nodes and properties for this.
Signed-off-by: Chris Packham <chris.packham@xxxxxxxxxxxxxxxxxxx>
---
This is based on the Marvell SDK. I've re-ordered the port entries to
be in ascending order renamed the wan ports and connected the SFP+.
Changes in v2:
- Remove unused port0
- Label all ports "pN"
- Add interrupt connections
- Add SFP
arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 129 ++++++++++++++++++++
1 file changed, 129 insertions(+)
diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
index 0885c6339d1b..d600422afd6c 100644
--- a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
@@ -73,6 +73,16 @@ cp0_reg_sd_vcc: cp0_sd_vcc@0 {
enable-active-high;
regulator-always-on;
};
+
+ sfp: sfp {
+ compatible = "sff,sfp";
+ i2c-bus = <&cp0_i2c1>;
+ mod-def0-gpios = <&expander0 3 GPIO_ACTIVE_LOW>;
+ los-gpio = <&expander0 15 GPIO_ACTIVE_HIGH>;
+ tx-disable-gpio = <&expander0 2 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&cp0_gpio1 24 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
};
&uart0 {
@@ -195,6 +205,125 @@ &cp0_mdio {
phy0: ethernet-phy@0 {
reg = <0>;
};
+
+ switch6: switch0@6 {
+ /* Actual device is MV88E6393X */
+ compatible = "marvell,mv88e6190";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ interrupt-parent = <&cp0_gpio1>;
+ interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ dsa,member = <0 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ label = "p1";
+ phy-handle = <&switch0phy1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "p2";
+ phy-handle = <&switch0phy2>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "p3";
+ phy-handle = <&switch0phy3>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "p4";
+ phy-handle = <&switch0phy4>;
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "p5";
+ phy-handle = <&switch0phy5>;
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "p6";
+ phy-handle = <&switch0phy6>;
+ };
+
+ port@7 {
+ reg = <7>;
+ label = "p7";
+ phy-handle = <&switch0phy7>;
+ };
+
+ port@8 {
+ reg = <8>;
+ label = "p8";
+ phy-handle = <&switch0phy8>;
+ };
+
+ port@9 {
+ reg = <9>;
+ label = "p9";
+ phy-mode = "10gbase-r";
+ sfp = <&sfp>;
+ managed = "in-band-status";
+ };
+
+ port@10 {
+ reg = <10>;
+ label = "cpu";
+ ethernet = <&cp0_eth0>;
+ };
+
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch0phy1: switch0phy1@1 {
+ reg = <0x1>;
+ };
+
+ switch0phy2: switch0phy2@2 {
+ reg = <0x2>;
+ };
+
+ switch0phy3: switch0phy3@3 {
+ reg = <0x3>;
+ };
+
+ switch0phy4: switch0phy4@4 {
+ reg = <0x4>;
+ };
+
+ switch0phy5: switch0phy5@5 {
+ reg = <0x5>;
+ };
+
+ switch0phy6: switch0phy6@6 {
+ reg = <0x6>;
+ };
+
+ switch0phy7: switch0phy7@7 {
+ reg = <0x7>;
+ };
+
+ switch0phy8: switch0phy8@8 {
+ reg = <0x8>;
+ };
+ };
+ };
};
&cp0_xmdio {
--
2.33.0
