Hi Robert,
> Globalscale MOCHAbin is a Armada 7040 based development board.
>
> Specifications:
> * Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
> * 2 / 4 / 8 GB of DDR4 DRAM
> * 16 GB eMMC
> * 4MB SPI-NOR (Bootloader)
> * 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
> * 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
> * 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
> * 1x SATA 7+15 socket (SATA3)
> * 1x 16-pin (2×8) MikroBus Connector
> * 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
> * 2x USB3.0 Type-A ports via SMSC USB5434B hub
> * Cortex 2x5 JTAG
> * microUSB port for UART (PL2303GL/PL2303SA onboard)
> * 1x 10G SFP+
> * 1x 1G SFP (Connected to 88E1512 PHY)
> * 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
> * 4x 1G RJ45 ports via Topaz 88E6141 switch
> * RTC with battery holder (SoC provided, requires CR2032 battery)
> * 1x 12V DC IN
> * 1x Power switch
> * 1x 12V fan header (3-pin, power only)
> * 1x mini-PCIe LED header (2x0.1" pins)
> * 1x M.2-2280 LED header (2x0.1" pins)
> * 6x Bootstrap jumpers
> * 1x Power LED (Green)
> * 3x Tri-color RGB LEDs (Controllable)
> * 1x Microchip ATECC608B secure element
>
> Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
> parallel connected to the same PHY.
>
> Signed-off-by: Robert Marko <robert.marko@xxxxxxxxxx>
> Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
Applied on mvebu/dt64
Thanks,
Gregory
> ---
> Changes in v6:
> * Use reset-gpios instead of reset-gpio per the DT binding
> * Add the CLKREQ PCIe pinmux
>
> Changes in v5:
> * Change LED labels to use the common "color:name" format instead
>
> Changes in v4:
> * Rename the "u-boot" partition to "firmware" which is more appropriate
> as it a concatenation of mv-ddr + TF-A + U-boot
>
> Changes in v3:
> * Use IRQ_TYPE_LEVEL_LOW instead of IRQ_TYPE_EDGE_FALLING as both the
> PCA9554 and Topaz switch have an active LOW IRQ signal.
>
> Changes in v2:
> * Use "10gbase-r" instead of "10gbase-kr"
> ---
> arch/arm64/boot/dts/marvell/Makefile | 1 +
> .../boot/dts/marvell/armada-7040-mochabin.dts | 458 ++++++++++++++++++
> 2 files changed, 459 insertions(+)
> create mode 100644 arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
>
> diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
> index 34efe0fb6f37..4d3a2ae9adbd 100644
> --- a/arch/arm64/boot/dts/marvell/Makefile
> +++ b/arch/arm64/boot/dts/marvell/Makefile
> @@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
> +dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-mochabin.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
> diff --git a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
> new file mode 100644
> index 000000000000..f3b0d57a24a3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
> @@ -0,0 +1,458 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Device Tree file for Globalscale MOCHAbin
> + * Copyright (C) 2019 Globalscale technologies, Inc.
> + * Copyright (C) 2021 Sartura Ltd.
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include "armada-7040.dtsi"
> +
> +/ {
> + model = "Globalscale MOCHAbin";
> + compatible = "globalscale,mochabin", "marvell,armada7040",
> + "marvell,armada-ap806-quad", "marvell,armada-ap806";
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + aliases {
> + ethernet0 = &cp0_eth0;
> + ethernet1 = &cp0_eth1;
> + ethernet2 = &cp0_eth2;
> + ethernet3 = &swport1;
> + ethernet4 = &swport2;
> + ethernet5 = &swport3;
> + ethernet6 = &swport4;
> + };
> +
> + /* SFP+ 10G */
> + sfp_eth0: sfp-eth0 {
> + compatible = "sff,sfp";
> + i2c-bus = <&cp0_i2c1>;
> + los-gpio = <&sfp_gpio 3 GPIO_ACTIVE_HIGH>;
> + mod-def0-gpio = <&sfp_gpio 2 GPIO_ACTIVE_LOW>;
> + tx-disable-gpio = <&sfp_gpio 1 GPIO_ACTIVE_HIGH>;
> + tx-fault-gpio = <&sfp_gpio 0 GPIO_ACTIVE_HIGH>;
> + };
> +
> + /* SFP 1G */
> + sfp_eth2: sfp-eth2 {
> + compatible = "sff,sfp";
> + i2c-bus = <&cp0_i2c0>;
> + los-gpio = <&sfp_gpio 7 GPIO_ACTIVE_HIGH>;
> + mod-def0-gpio = <&sfp_gpio 6 GPIO_ACTIVE_LOW>;
> + tx-disable-gpio = <&sfp_gpio 5 GPIO_ACTIVE_HIGH>;
> + tx-fault-gpio = <&sfp_gpio 4 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +/* microUSB UART console */
> +&uart0 {
> + status = "okay";
> +
> + pinctrl-0 = <&uart0_pins>;
> + pinctrl-names = "default";
> +};
> +
> +/* eMMC */
> +&ap_sdhci0 {
> + status = "okay";
> +
> + bus-width = <4>;
> + non-removable;
> + /delete-property/ marvell,xenon-phy-slow-mode;
> + no-1-8-v;
> +};
> +
> +&cp0_pinctrl {
> + cp0_uart0_pins: cp0-uart0-pins {
> + marvell,pins = "mpp6", "mpp7";
> + marvell,function = "uart0";
> + };
> +
> + cp0_spi0_pins: cp0-spi0-pins {
> + marvell,pins = "mpp56", "mpp57", "mpp58", "mpp59";
> + marvell,function = "spi0";
> + };
> +
> + cp0_spi1_pins: cp0-spi1-pins {
> + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
> + marvell,function = "spi1";
> + };
> +
> + cp0_i2c0_pins: cp0-i2c0-pins {
> + marvell,pins = "mpp37", "mpp38";
> + marvell,function = "i2c0";
> + };
> +
> + cp0_i2c1_pins: cp0-i2c1-pins {
> + marvell,pins = "mpp2", "mpp3";
> + marvell,function = "i2c1";
> + };
> +
> + pca9554_int_pins: pca9554-int-pins {
> + marvell,pins = "mpp27";
> + marvell,function = "gpio";
> + };
> +
> + cp0_rgmii1_pins: cp0-rgmii1-pins {
> + marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47", "mpp48", "mpp49",
> + "mpp50", "mpp51", "mpp52", "mpp53", "mpp54", "mpp55";
> + marvell,function = "ge1";
> + };
> +
> + is31_sdb_pins: is31-sdb-pins {
> + marvell,pins = "mpp30";
> + marvell,function = "gpio";
> + };
> +
> + cp0_pcie_reset_pins: cp0-pcie-reset-pins {
> + marvell,pins = "mpp9";
> + marvell,function = "gpio";
> + };
> +
> + cp0_pcie_clkreq_pins: cp0-pcie-clkreq-pins {
> + marvell,pins = "mpp5";
> + marvell,function = "pcie1";
> + };
> +
> + cp0_switch_pins: cp0-switch-pins {
> + marvell,pins = "mpp0", "mpp1";
> + marvell,function = "gpio";
> + };
> +
> + cp0_phy_pins: cp0-phy-pins {
> + marvell,pins = "mpp12";
> + marvell,function = "gpio";
> + };
> +};
> +
> +/* mikroBUS UART */
> +&cp0_uart0 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_uart0_pins>;
> +};
> +
> +/* mikroBUS SPI */
> +&cp0_spi0 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_spi0_pins>;
> +};
> +
> +/* SPI-NOR */
> +&cp0_spi1{
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_spi1_pins>;
> +
> + spi-flash@0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <20000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "firmware";
> + reg = <0x0 0x3e0000>;
> + read-only;
> + };
> +
> + partition@3e0000 {
> + label = "hw-info";
> + reg = <0x3e0000 0x10000>;
> + read-only;
> + };
> +
> + partition@3f0000 {
> + label = "u-boot-env";
> + reg = <0x3f0000 0x10000>;
> + };
> + };
> + };
> +};
> +
> +/* mikroBUS, 1G SFP and GPIO expander */
> +&cp0_i2c0 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_i2c0_pins>;
> + clock-frequency = <100000>;
> +
> + sfp_gpio: pca9554@39 {
> + compatible = "nxp,pca9554";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pca9554_int_pins>;
> + reg = <0x39>;
> +
> + interrupt-parent = <&cp0_gpio1>;
> + interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + /*
> + * IO0_0: SFP+_TX_FAULT
> + * IO0_1: SFP+_TX_DISABLE
> + * IO0_2: SFP+_PRSNT
> + * IO0_3: SFP+_LOSS
> + * IO0_4: SFP_TX_FAULT
> + * IO0_5: SFP_TX_DISABLE
> + * IO0_6: SFP_PRSNT
> + * IO0_7: SFP_LOSS
> + */
> + };
> +};
> +
> +/* IS31FL3199, mini-PCIe and 10G SFP+ */
> +&cp0_i2c1 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_i2c1_pins>;
> + clock-frequency = <100000>;
> +
> + leds@64 {
> + compatible = "issi,is31fl3199";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&is31_sdb_pins>;
> + shutdown-gpios = <&cp0_gpio1 30 GPIO_ACTIVE_HIGH>;
> + reg = <0x64>;
> +
> + led1_red: led@1 {
> + label = "red:led1";
> + reg = <1>;
> + led-max-microamp = <20000>;
> + };
> +
> + led1_green: led@2 {
> + label = "green:led1";
> + reg = <2>;
> + };
> +
> + led1_blue: led@3 {
> + label = "blue:led1";
> + reg = <3>;
> + };
> +
> + led2_red: led@4 {
> + label = "red:led2";
> + reg = <4>;
> + };
> +
> + led2_green: led@5 {
> + label = "green:led2";
> + reg = <5>;
> + };
> +
> + led2_blue: led@6 {
> + label = "blue:led2";
> + reg = <6>;
> + };
> +
> + led3_red: led@7 {
> + label = "red:led3";
> + reg = <7>;
> + };
> +
> + led3_green: led@8 {
> + label = "green:led3";
> + reg = <8>;
> + };
> +
> + led3_blue: led@9 {
> + label = "blue:led3";
> + reg = <9>;
> + };
> + };
> +};
> +
> +&cp0_mdio {
> + status = "okay";
> +
> + /* 88E1512 PHY */
> + eth2phy: ethernet-phy@1 {
> + reg = <1>;
> + sfp = <&sfp_eth2>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_phy_pins>;
> + reset-gpios = <&cp0_gpio1 12 GPIO_ACTIVE_LOW>;
> + };
> +
> + /* 88E6141 Topaz switch */
> + switch: switch@3 {
> + compatible = "marvell,mv88e6085";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_switch_pins>;
> + reset-gpios = <&cp0_gpio1 0 GPIO_ACTIVE_LOW>;
> +
> + interrupt-parent = <&cp0_gpio1>;
> + interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + swport1: port@1 {
> + reg = <1>;
> + label = "lan0";
> + phy-handle = <&swphy1>;
> + };
> +
> + swport2: port@2 {
> + reg = <2>;
> + label = "lan1";
> + phy-handle = <&swphy2>;
> + };
> +
> + swport3: port@3 {
> + reg = <3>;
> + label = "lan2";
> + phy-handle = <&swphy3>;
> + };
> +
> + swport4: port@4 {
> + reg = <4>;
> + label = "lan3";
> + phy-handle = <&swphy4>;
> + };
> +
> + port@5 {
> + reg = <5>;
> + label = "cpu";
> + ethernet = <&cp0_eth1>;
> + phy-mode = "2500base-x";
> + managed = "in-band-status";
> + };
> + };
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + swphy1: swphy1@17 {
> + reg = <17>;
> + };
> +
> + swphy2: swphy2@18 {
> + reg = <18>;
> + };
> +
> + swphy3: swphy3@19 {
> + reg = <19>;
> + };
> +
> + swphy4: swphy4@20 {
> + reg = <20>;
> + };
> + };
> + };
> +};
> +
> +&cp0_ethernet {
> + status = "okay";
> +};
> +
> +/* 10G SFP+ */
> +&cp0_eth0 {
> + status = "okay";
> +
> + phy-mode = "10gbase-r";
> + phys = <&cp0_comphy4 0>;
> + managed = "in-band-status";
> + sfp = <&sfp_eth0>;
> +};
> +
> +/* Topaz switch uplink */
> +&cp0_eth1 {
> + status = "okay";
> +
> + phy-mode = "2500base-x";
> + phys = <&cp0_comphy0 1>;
> +
> + fixed-link {
> + speed = <2500>;
> + full-duplex;
> + };
> +};
> +
> +/* 1G SFP or 1G RJ45 */
> +&cp0_eth2 {
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&cp0_rgmii1_pins>;
> +
> + phy = <ð2phy>;
> + phy-mode = "rgmii-id";
> +};
> +
> +&cp0_utmi {
> + status = "okay";
> +};
> +
> +/* SMSC USB5434B hub */
> +&cp0_usb3_0 {
> + status = "okay";
> +
> + phys = <&cp0_comphy1 0>, <&cp0_utmi0>;
> + phy-names = "cp0-usb3h0-comphy", "utmi";
> +};
> +
> +/* miniPCI-E USB */
> +&cp0_usb3_1 {
> + status = "okay";
> +};
> +
> +&cp0_sata0 {
> + status = "okay";
> +
> + /* 7 + 12 SATA connector (J24) */
> + sata-port@0 {
> + phys = <&cp0_comphy2 0>;
> + phy-names = "cp0-sata0-0-phy";
> + };
> +
> + /* M.2-2250 B-key (J39) */
> + sata-port@1 {
> + phys = <&cp0_comphy3 1>;
> + phy-names = "cp0-sata0-1-phy";
> + };
> +};
> +
> +/* miniPCI-E (J5) */
> +&cp0_pcie2 {
> + status = "okay";
> +
> + pinctrl-names = "default", "clkreq";
> + pinctrl-0 = <&cp0_pcie_reset_pins>;
> + pinctrl-1 = <&cp0_pcie_clkreq_pins>;
> + phys = <&cp0_comphy5 2>;
> + phy-names = "cp0-pcie2-x1-phy";
> + reset-gpios = <&cp0_gpio1 9 GPIO_ACTIVE_LOW>;
> +};
> --
> 2.33.0
>
--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com
