From: Alexandru Tachici <alexandru.tachici@xxxxxxxxxx>
The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for
industrial Ethernet applications and is compliant with the IEEE 802.3cg
Ethernet standard for long reach 10 Mb/s Single Pair Ethernet.
The ADIN1100 uses Auto-Negotiation capability in accordance
with IEEE 802.3 Clause 98, providing a mechanism for
exchanging information between PHYs to allow link partners to
agree to a common mode of operation.
The concluded operating mode is the transmit amplitude mode and
master/slave preference common across the two devices.
Both device and LP advertise their ability and request for
increased transmit at:
- BASE-T1 autonegotiation advertisement register [47:32]\
Clause 45.2.7.21 of Standard 802.3
- BIT(13) - 10BASE-T1L High Level Transmit Operating Mode Ability
- BIT(12) - 10BASE-T1L High Level Transmit Operating Mode Request
For 2.4 Vpp (high level transmit) operation, both devices need
to have the High Level Transmit Operating Mode Ability bit set,
and only one of them needs to have the High Level Transmit
Operating Mode Request bit set. Otherwise 1.0 Vpp transmit level
will be used.
Ethtool output:
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT1L/Full
Supported pause frame use: Transmit-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT1L/Full
Advertised pause frame use: Transmit-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT1L/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 10Mb/s
Duplex: Full
Auto-negotiation: on
master-slave cfg: preferred master
master-slave status: master
Port: MII
PHYAD: 0
Transceiver: external
Link detected: yes
SQI: 7/7
1. Add basic support for ADIN1100.
Alexandru Ardelean (1):
net: phy: adin1100: Add initial support for ADIN1100 industrial PHY
1. Added 10baset-T1L link modes.
2. Added 10-BasetT1L registers that are used in ADIN1100 driver.
3. Added BaseT1 auto-negotiation registers. For ADIN1100 these
registers decide master/slave status and TX voltage of the
device and link partner.
4. Allow user to set the master-slave configuration of ADIN1100.
5. Convert MSE to SQI using a predefined table and allow user access
through ethtool.
6. DT bindings for the 2.4 Vpp transmit mode.
7. DT bindings for ADIN1100.
Alexandru Tachici (7):
ethtool: Add 10base-T1L link mode entry
net: phy: Add 10-BaseT1L registers
net: phy: Add BaseT1 auto-negotiation registers
net: phy: adin1100: Add ethtool master-slave support
net: phy: adin1100: Add SQI support
dt-bindings: net: phy: Add 10-baseT1L 2.4 Vpp
dt-bindings: adin1100: Add binding for ADIN1100 Ethernet PHY
Changelog V2 -> V3:
- removed unused defines
- dropped 1 V 2.4 V voltage link entries (will add these features in a separate patch)
- dropped extra PHY stats, will add them in a separate patch
(adin1200/1300 will need rework too as it implements same stats)
- added PMA status register and PCS control register in mdio.h (registers specified in 802.3gc)
- added auto-negotiation advertisement and link partner registers in mdio.h
(Registers specified in 802.3 2018)
- added 10base-t1l-2.4vpp tristate property to ethernet-phy yaml
- replaced standard registers defines in adin1100.c with the ones added to mdio.h
.../devicetree/bindings/net/adi,adin1100.yaml | 30 ++
.../devicetree/bindings/net/ethernet-phy.yaml | 9 +
drivers/net/phy/Kconfig | 7 +
drivers/net/phy/Makefile | 1 +
drivers/net/phy/adin1100.c | 403 ++++++++++++++++++
drivers/net/phy/phy-core.c | 3 +-
include/uapi/linux/ethtool.h | 1 +
include/uapi/linux/mdio.h | 56 +++
net/ethtool/common.c | 3 +
9 files changed, 512 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/net/adi,adin1100.yaml
create mode 100644 drivers/net/phy/adin1100.c
--
2.25.1
