Convert the ST ST21NFCA NFC controller to DT schema format. Changes during bindings conversion: 1. Add a new required "interrupts" property, because it was missing in the old bindings by mistake. 2. Drop the "clock-frequency" property during conversion because it is a property of I2C bus controller, not I2C slave device. It was also never used by the driver. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxxxxx> --- .../bindings/net/nfc/st,st21nfca.yaml | 64 +++++++++++++++++++ .../devicetree/bindings/net/nfc/st21nfca.txt | 37 ----------- 2 files changed, 64 insertions(+), 37 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/nfc/st,st21nfca.yaml delete mode 100644 Documentation/devicetree/bindings/net/nfc/st21nfca.txt diff --git a/Documentation/devicetree/bindings/net/nfc/st,st21nfca.yaml b/Documentation/devicetree/bindings/net/nfc/st,st21nfca.yaml new file mode 100644 index 000000000000..4356eacde8aa --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st,st21nfca.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/nfc/st,st21nfca.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics SAS ST21NFCA NFC controller + +maintainers: + - Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxxxxx> + +properties: + compatible: + const: st,st21nfca-i2c + + enable-gpios: + description: Output GPIO pin used for enabling/disabling the controller + + ese-present: + type: boolean + description: | + Specifies that an ese is physically connected to the controller + + interrupts: + maxItems: 1 + + reg: + maxItems: 1 + + uicc-present: + type: boolean + description: | + Specifies that the uicc swp signal can be physically connected to the + controller + +required: + - compatible + - enable-gpios + - interrupts + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + nfc@1 { + compatible = "st,st21nfca-i2c"; + reg = <0x1>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; + }; + }; diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt deleted file mode 100644 index b8bd90f80e12..000000000000 --- a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt +++ /dev/null @@ -1,37 +0,0 @@ -* STMicroelectronics SAS. ST21NFCA NFC Controller - -Required properties: -- compatible: Should be "st,st21nfca-i2c". -- clock-frequency: I²C work frequency. -- reg: address on the bus -- enable-gpios: Output GPIO pin used for enabling/disabling the ST21NFCA - -Optional SoC Specific Properties: -- pinctrl-names: Contains only one value - "default". -- pintctrl-0: Specifies the pin control groups used for this controller. -- ese-present: Specifies that an ese is physically connected to the nfc -controller. -- uicc-present: Specifies that the uicc swp signal can be physically -connected to the nfc controller. - -Example (for ARM-based BeagleBoard xM with ST21NFCA on I2C2): - -&i2c2 { - - - st21nfca: st21nfca@1 { - - compatible = "st,st21nfca-i2c"; - - reg = <0x01>; - clock-frequency = <400000>; - - interrupt-parent = <&gpio5>; - interrupts = <2 IRQ_TYPE_LEVEL_LOW>; - - enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; - - ese-present; - uicc-present; - }; -}; -- 2.30.2
