Document binding for configurable led. Ports led can now be set on/off
and the blink/on rules can be configured using the "qca,led_rules"
binding. Refer to the Documentation on how to configure them.
Signed-off-by: Ansuel Smith <ansuelsmth@xxxxxxxxx>
---
.../devicetree/bindings/net/dsa/qca8k.txt | 249 ++++++++++++++++++
1 file changed, 249 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt
index 8c73f67c43ca..233f02cd9e98 100644
--- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt
+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt
@@ -29,6 +29,45 @@ the mdio MASTER is used as communication.
Don't use mixed external and internal mdio-bus configurations, as this is
not supported by the hardware.
+A leds subnode can be declared to configure leds port behaviour.
+The leds subnode must declare the port with the mdio reg that will have the
+attached led. Each port can have a max of 3 different leds. (Refer to example)
+A led can have 4 different settings:
+- Always off
+- Always on
+- Blink at 4hz
+- Hw_mode: This special mode follow control_rule rules and blink based on switch
+event.
+A sysfs entry for control_rule and hw_mode is provided for each led.
+Control rule for phy0-3 are shared and refer to the same reg. That means that
+phy0-3 will blink based on the same rules. Phy4 have its dedicated control_rules.
+
+Each led can have the following binding:
+The binding "default-state" can be declared to set them off by default or to
+follow leds control_rule using the keep value. By default hw_mode is set as it's
+the default switch setting.
+The binding "qca,led_rules" can be used to declare the control_rule set on
+switch setup. The following rules can be applied decalred in an array of string
+in the dts:
+- tx-blink: Led blink on tx traffic for the port
+- rx-blink: Led blink on rx traffic for the port
+- collision-blink: Led blink when a collision is detected for the port
+- link-10M: Led is turned on when a link of 10M is detected for the port
+- link-100M: Led is turned on when a link of 100M is detected for the port
+- link-1000M: Led is turned on when a link of 1000M is detected for the port
+- half-duplex: Led is turned on when a half-duplex link is detected for the port
+- full-duplex: Led is turned on when a full-duplex link is detected for the port
+- linkup-over: Led blinks only when the linkup led is on, ignore blink otherwise
+- power-on-reset: Reset led on switch reset
+- One of
+ - blink-2hz: Led blinks at 2hz frequency
+ - blink-4hz: Led blinks at 4hz frequency
+ - blink-8hz: Led blinks at 8hz frequency
+ - blink-auto: Led blinks at 2hz frequency with 10M, 4hz with 100M, 8hz
+ with 1000M
+Due to the phy0-3 limitation, multiple use of 'qca8k_led_rules' will result in
+the last defined one to be applied.
+
The CPU port of this switch is always port 0.
A CPU port node has the following optional node:
@@ -213,3 +252,213 @@ for the internal master mdio-bus configuration:
};
};
};
+
+for the leds declaration example:
+
+#include <dt-bindings/leds/common.h>
+
+ &mdio0 {
+ switch@10 {
+ compatible = "qca,qca8337";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+ reg = <0x10>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "cpu";
+ ethernet = <&gmac1>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = 1000;
+ full-duplex;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-mode = "internal";
+ phy-handle = <&phy_port1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-mode = "internal";
+ phy-handle = <&phy_port2>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-mode = "internal";
+ phy-handle = <&phy_port3>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ phy-mode = "internal";
+ phy-handle = <&phy_port4>;
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "wan";
+ phy-mode = "internal";
+ phy-handle = <&phy_port5>;
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy_port1: phy@0 {
+ reg = <0>;
+ };
+
+ phy_port2: phy@1 {
+ reg = <1>;
+ };
+
+ phy_port3: phy@2 {
+ reg = <2>;
+ };
+
+ phy_port4: phy@3 {
+ reg = <3>;
+ };
+
+ phy_port5: phy@4 {
+ reg = <4>;
+ };
+ };
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "keep";
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_AMBER>;
+ default-state = "keep";
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
+ };
+ };
+
+ phy@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <1>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "keep";
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <2>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_AMBER>;
+ default-state = "keep";
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <2>;
+ };
+ };
+
+ phy@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <2>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "keep";
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <3>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_AMBER>;
+ default-state = "keep";
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <3>;
+ };
+ };
+
+ phy@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <3>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "keep";
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <4>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_AMBER>;
+ default-state = "keep";
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <4>;
+ };
+ };
+
+ phy@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <4>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "keep";
+ function = LED_FUNCTION_WAN;
+ qca,led_rules = "tx-blink", "rx-blink", "link-1000M", "full-duplex", "linkup-over", "blink-8hz";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_AMBER>;
+ default-state = "keep";
+ function = LED_FUNCTION_WAN;
+ };
+ };
+ };
+ };
+ };
\ No newline at end of file
--
2.32.0
