On Wed, Sep 01, 2021 at 11:18:27AM +0200, Maxime Ripard wrote:
> The Omnivision OV5640 is supported by Linux thanks to its device tree
> binding.
>
> Now that we have the DT validation in place, let's convert the device
> tree bindings for that driver over to a YAML schema.
>
> Cc: linux-media@xxxxxxxxxxxxxxx
> Cc: Mauro Carvalho Chehab <mchehab@xxxxxxxxxx>
> Cc: Steve Longerbeam <slongerbeam@xxxxxxxxx>
> Signed-off-by: Maxime Ripard <maxime@xxxxxxxxxx>
> ---
> .../devicetree/bindings/media/i2c/ov5640.txt | 92 -----------
> .../bindings/media/i2c/ovti,ov5640.yaml | 154 ++++++++++++++++++
> 2 files changed, 154 insertions(+), 92 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt
> create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
> deleted file mode 100644
> index c97c2f2da12d..000000000000
> --- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt
> +++ /dev/null
> @@ -1,92 +0,0 @@
> -* Omnivision OV5640 MIPI CSI-2 / parallel sensor
> -
> -Required Properties:
> -- compatible: should be "ovti,ov5640"
> -- clocks: reference to the xclk input clock.
> -- clock-names: should be "xclk".
> -- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
> -- AVDD-supply: Analog voltage supply, 2.8 volts
> -- DVDD-supply: Digital core voltage supply, 1.5 volts
> -
> -Optional Properties:
> -- reset-gpios: reference to the GPIO connected to the reset pin, if any.
> - This is an active low signal to the OV5640.
> -- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
> - if any. This is an active high signal to the OV5640.
> -- rotation: as defined in
> - Documentation/devicetree/bindings/media/video-interfaces.txt,
> - valid values are 0 (sensor mounted upright) and 180 (sensor
> - mounted upside down).
> -
> -The device node must contain one 'port' child node for its digital output
> -video port, in accordance with the video interface bindings defined in
> -Documentation/devicetree/bindings/media/video-interfaces.txt.
> -
> -OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint.
> -
> -Endpoint node required properties for CSI-2 connection are:
> -- remote-endpoint: a phandle to the bus receiver's endpoint node.
> -- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
> -- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported)
> -
> -Endpoint node required properties for parallel connection are:
> -- remote-endpoint: a phandle to the bus receiver's endpoint node.
> -- bus-width: shall be set to <8> for 8 bits parallel bus
> - or <10> for 10 bits parallel bus
> -- data-shift: shall be set to <2> for 8 bits parallel bus
> - (lines 9:2 are used) or <0> for 10 bits parallel bus
> -- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
> -- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
> -- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
> - signal.
> -
> -Examples:
> -
> -&i2c1 {
> - ov5640: camera@3c {
> - compatible = "ovti,ov5640";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ov5640>;
> - reg = <0x3c>;
> - clocks = <&clks IMX6QDL_CLK_CKO>;
> - clock-names = "xclk";
> - DOVDD-supply = <&vgen4_reg>; /* 1.8v */
> - AVDD-supply = <&vgen3_reg>; /* 2.8v */
> - DVDD-supply = <&vgen2_reg>; /* 1.5v */
> - powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
> - reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
> - rotation = <180>;
> -
> - port {
> - /* MIPI CSI-2 bus endpoint */
> - ov5640_to_mipi_csi2: endpoint {
> - remote-endpoint = <&mipi_csi2_from_ov5640>;
> - clock-lanes = <0>;
> - data-lanes = <1 2>;
> - };
> - };
> - };
> -};
> -
> -&i2c1 {
> - ov5640: camera@3c {
> - compatible = "ovti,ov5640";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ov5640>;
> - reg = <0x3c>;
> - clocks = <&clk_ext_camera>;
> - clock-names = "xclk";
> -
> - port {
> - /* Parallel bus endpoint */
> - ov5640_to_parallel: endpoint {
> - remote-endpoint = <¶llel_from_ov5640>;
> - bus-width = <8>;
> - data-shift = <2>; /* lines 9:2 are used */
> - hsync-active = <0>;
> - vsync-active = <0>;
> - pclk-sample = <1>;
> - };
> - };
> - };
> -};
> diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
> new file mode 100644
> index 000000000000..0283b1895a75
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
> @@ -0,0 +1,154 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5640.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: OmniVision OV5640 Image Sensor Device Tree Bindings
> +
> +maintainers:
> + - Steve Longerbeam <slongerbeam@xxxxxxxxx>
> +
> +allOf:
> + - $ref: /schemas/media/video-interface-devices.yaml#
> +
> +properties:
> + compatible:
> + const: ovti,ov5640
> +
> + reg:
> + maxItems: 1
> +
> + clocks:
> + description: XCLK Input Clock
> +
> + clock-names:
> + const: xclk
> +
> + AVDD-supply:
> + description: Analog voltage supply, 2.8 volts
> +
> + DVDD-supply:
> + description: Digital core voltage supply, 1.5 volts
> +
> + DOVDD-supply:
> + description: Digital I/O voltage supply, 1.8 volts
> +
> + powerdown-gpios:
> + maxItems: 1
> + description: >
> + Reference to the GPIO connected to the powerdown pin, if any.
> +
> + reset-gpios:
> + maxItems: 1
> + description: >
> + Reference to the GPIO connected to the reset pin, if any.
> +
> + rotation:
> + enum:
> + - 0
> + - 180
> +
> + port:
> + description: Digital Output Port
> + $ref: /schemas/graph.yaml#/properties/port
This needs to be /schemas/graph.yaml#/$defs/port-base
Otherwise, it will fail when we start checking unevaluatedProperties.
> + additionalProperties: false
> +
> + properties:
> + endpoint:
> + $ref: /schemas/media/video-interfaces.yaml#
> + unevaluatedProperties: false
> +
> + properties:
> + clock-lanes:
> + const: 0
> +
> + data-lanes:
> + minItems: 1
> + maxItems: 2
> + items:
> + enum: [1, 2]
> +
> + bus-width:
> + enum: [8, 10]
> +
> + data-shift:
> + enum: [0, 2]
> +
> +required:
> + - compatible
> + - reg
> + - clocks
> + - clock-names
> + - AVDD-supply
> + - DVDD-supply
> + - DOVDD-supply
> + - port
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/imx6qdl-clock.h>
> + #include <dt-bindings/gpio/gpio.h>
> +
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + camera@3c {
> + compatible = "ovti,ov5640";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ov5640>;
> + reg = <0x3c>;
> + clocks = <&clks IMX6QDL_CLK_CKO>;
> + clock-names = "xclk";
> + DOVDD-supply = <&vgen4_reg>; /* 1.8v */
> + AVDD-supply = <&vgen3_reg>; /* 2.8v */
> + DVDD-supply = <&vgen2_reg>; /* 1.5v */
> + powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
> + rotation = <180>;
> +
> + port {
> + /* MIPI CSI-2 bus endpoint */
> + ov5640_to_mipi_csi2: endpoint {
> + remote-endpoint = <&mipi_csi2_from_ov5640>;
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
> + };
> +
> + - |
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + camera@3c {
> + compatible = "ovti,ov5640";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ov5640>;
> + reg = <0x3c>;
> + clocks = <&clk_ext_camera>;
> + clock-names = "xclk";
> + DOVDD-supply = <&vgen4_reg>; /* 1.8v */
> + AVDD-supply = <&vgen3_reg>; /* 2.8v */
> + DVDD-supply = <&vgen2_reg>; /* 1.5v */
> +
> + port {
> + /* Parallel bus endpoint */
> + ov5640_to_parallel: endpoint {
> + remote-endpoint = <¶llel_from_ov5640>;
> + bus-width = <8>;
> + data-shift = <2>; /* lines 9:2 are used */
> + hsync-active = <0>;
> + vsync-active = <0>;
> + pclk-sample = <1>;
> + };
> + };
> + };
> + };
> +
> +...
> --
> 2.31.1
>
>
