Convert the fsl,imx6q-pcie.txt into a schema.
- ranges property should be grouped by region, with no functional
changes.
- only one propert is allowed in the compatible string, remove
"snps,dw-pcie".
Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx>
---
.../bindings/pci/fsl,imx6q-pcie.txt | 100 ---------
.../bindings/pci/fsl,imx6q-pcie.yaml | 202 ++++++++++++++++++
MAINTAINERS | 2 +-
3 files changed, 203 insertions(+), 101 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
create mode 100644 Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
deleted file mode 100644
index d8971ab99274..000000000000
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
+++ /dev/null
@@ -1,100 +0,0 @@
-* Freescale i.MX6 PCIe interface
-
-This PCIe host controller is based on the Synopsys DesignWare PCIe IP
-and thus inherits all the common properties defined in designware-pcie.txt.
-
-Required properties:
-- compatible:
- - "fsl,imx6q-pcie"
- - "fsl,imx6sx-pcie",
- - "fsl,imx6qp-pcie"
- - "fsl,imx7d-pcie"
- - "fsl,imx8mq-pcie"
-- reg: base address and length of the PCIe controller
-- interrupts: A list of interrupt outputs of the controller. Must contain an
- entry for each entry in the interrupt-names property.
-- interrupt-names: Must include the following entries:
- - "msi": The interrupt that is asserted when an MSI is received
-- clock-names: Must include the following additional entries:
- - "pcie_phy"
-
-Optional properties:
-- fsl,tx-deemph-gen1: Gen1 De-emphasis value. Default: 0
-- fsl,tx-deemph-gen2-3p5db: Gen2 (3.5db) De-emphasis value. Default: 0
-- fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20
-- fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127
-- fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127
-- fsl,max-link-speed: Specify PCI gen for link capability. Must be '2' for
- gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock outputs
- do not meet gen2 jitter requirements and thus for gen2 capability a gen2
- compliant clock generator should be used and configured.
-- reset-gpio: Should specify the GPIO for controlling the PCI bus device reset
- signal. It's not polarity aware and defaults to active-low reset sequence
- (L=reset state, H=operation state).
-- reset-gpio-active-high: If present then the reset sequence using the GPIO
- specified in the "reset-gpio" property is reversed (H=reset state,
- L=operation state).
-- vpcie-supply: Should specify the regulator in charge of PCIe port power.
- The regulator will be enabled when initializing the PCIe host and
- disabled either as part of the init process or when shutting down the
- host.
-- vph-supply: Should specify the regulator in charge of VPH one of the three
- PCIe PHY powers. This regulator can be supplied by both 1.8v and 3.3v voltage
- supplies.
-
-Additional required properties for imx6sx-pcie:
-- clock names: Must include the following additional entries:
- - "pcie_inbound_axi"
-- power-domains: Must be set to phandles pointing to the DISPLAY and
- PCIE_PHY power domains
-- power-domain-names: Must be "pcie", "pcie_phy"
-
-Additional required properties for imx7d-pcie and imx8mq-pcie:
-- power-domains: Must be set to a phandle pointing to PCIE_PHY power domain
-- resets: Must contain phandles to PCIe-related reset lines exposed by SRC
- IP block
-- reset-names: Must contain the following entries:
- - "pciephy"
- - "apps"
- - "turnoff"
-- fsl,imx7d-pcie-phy: A phandle to an fsl,imx7d-pcie-phy node.
-
-Additional required properties for imx8mq-pcie:
-- clock-names: Must include the following additional entries:
- - "pcie_aux"
-
-Example:
-
- pcie@01000000 {
- compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
- reg = <0x01ffc000 0x04000>,
- <0x01f00000 0x80000>;
- reg-names = "dbi", "config";
- #address-cells = <3>;
- #size-cells = <2>;
- device_type = "pci";
- ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000
- 0x81000000 0 0 0x01f80000 0 0x00010000
- 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
- num-lanes = <1>;
- interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "msi";
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0x7>;
- interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
- <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
- <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
- <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks 144>, <&clks 206>, <&clks 189>;
- clock-names = "pcie", "pcie_bus", "pcie_phy";
- };
-
-* Freescale i.MX7d PCIe PHY
-
-This is the PHY associated with the IMX7d PCIe controller. It's used by the
-PCI-e controller via the fsl,imx7d-pcie-phy phandle.
-
-Required properties:
-- compatible:
- - "fsl,imx7d-pcie-phy"
-- reg: base address and length of the PCIe PHY controller
diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
new file mode 100644
index 000000000000..2911e565b260
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
@@ -0,0 +1,202 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX6 PCIe host controller
+
+maintainers:
+ - Lucas Stach <l.stach@xxxxxxxxxxxxxx>
+ - Richard Zhu <hongxing.zhu@xxxxxxx>
+
+description: |+
+ This PCIe host controller is based on the Synopsys DesignWare PCIe IP
+ and thus inherits all the common properties defined in snps,dw-pcie.yaml.
+
+allOf:
+ - $ref: /schemas/pci/snps,dw-pcie.yaml#
+
+properties:
+ compatible:
+ enum:
+ - fsl,imx6q-pcie
+ - fsl,imx6sx-pcie
+ - fsl,imx6qp-pcie
+ - fsl,imx7d-pcie
+ - fsl,imx8mq-pcie
+
+ reg:
+ items:
+ - description: Data Bus Interface (DBI) registers.
+ - description: PCIe configuration space region.
+
+ reg-names:
+ items:
+ - const: dbi
+ - const: config
+
+ interrupts:
+ items:
+ - description: builtin MSI controller.
+
+ interrupt-names:
+ minItems: 1
+ items:
+ - const: msi
+
+ clocks:
+ minItems: 3
+ items:
+ - description: PCIe bridge clock.
+ - description: PCIe bus clock.
+ - description: PCIe PHY clock.
+ - description: Additional required clock entry for imx6sx-pcie,
+ imx8mq-pcie.
+
+ clock-names:
+ minItems: 3
+ items:
+ - const: pcie
+ - const: pcie_bus
+ - const: pcie_phy
+ - const: pcie_inbound_axi for imx6sx-pcie, pcie_aux for imx8mq-pcie
+
+ num-lanes:
+ const: 1
+
+ fsl,imx7d-pcie-phy:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: A phandle to an fsl,imx7d-pcie-phy node. Additional
+ required properties for imx7d-pcie and imx8mq-pcie.
+
+ power-domains:
+ items:
+ - description: The phandle pointing to the DISPLAY domain for
+ imx6sx-pcie, to PCIE_PHY power domain for imx7d-pcie and
+ imx8mq-pcie.
+ - description: The phandle pointing to the PCIE_PHY power domains
+ for imx6sx-pcie.
+
+ power-domain-names:
+ items:
+ - const: pcie
+ - const: pcie_phy
+
+ resets:
+ maxItems: 3
+ description: Phandles to PCIe-related reset lines exposed by SRC
+ IP block. Additional required by imx7d-pcie and imx8mq-pcie.
+
+ reset-names:
+ items:
+ - const: pciephy
+ - const: apps
+ - const: turnoff
+
+ fsl,tx-deemph-gen1:
+ description: Gen1 De-emphasis value (optional required).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 0
+
+ fsl,tx-deemph-gen2-3p5db:
+ description: Gen2 (3.5db) De-emphasis value (optional required).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 0
+
+ fsl,tx-deemph-gen2-6db:
+ description: Gen2 (6db) De-emphasis value (optional required).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 20
+
+ fsl,tx-swing-full:
+ description: Gen2 TX SWING FULL value (optional required).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 127
+
+ fsl,tx-swing-low:
+ description: TX launch amplitude swing_low value (optional required).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 127
+
+ fsl,max-link-speed:
+ description: Specify PCI Gen for link capability (optional required).
+ Note that the IMX6 LVDS clock outputs do not meet gen2 jitter
+ requirements and thus for gen2 capability a gen2 compliant clock
+ generator should be used and configured.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2, 3, 4]
+ default: 1
+
+ reset-gpio:
+ description: Should specify the GPIO for controlling the PCI bus device
+ reset signal. It's not polarity aware and defaults to active-low reset
+ sequence (L=reset state, H=operation state) (optional required).
+
+ reset-gpio-active-high:
+ description: If present then the reset sequence using the GPIO
+ specified in the "reset-gpio" property is reversed (H=reset state,
+ L=operation state) (optional required).
+
+ vpcie-supply:
+ description: Should specify the regulator in charge of PCIe port power.
+ The regulator will be enabled when initializing the PCIe host and
+ disabled either as part of the init process or when shutting down
+ the host (optional required).
+
+ vph-supply:
+ description: Should specify the regulator in charge of VPH one of
+ the three PCIe PHY powers. This regulator can be supplied by both
+ 1.8v and 3.3v voltage supplies (optional required).
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - "#address-cells"
+ - "#size-cells"
+ - device_type
+ - bus-range
+ - ranges
+ - num-lanes
+ - interrupts
+ - interrupt-names
+ - "#interrupt-cells"
+ - interrupt-map-mask
+ - interrupt-map
+ - clocks
+ - clock-names
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/imx6qdl-clock.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ pcie: pcie@1ffc000 {
+ compatible = "fsl,imx6q-pcie";
+ reg = <0x01ffc000 0x04000>,
+ <0x01f00000 0x80000>;
+ reg-names = "dbi", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ bus-range = <0x00 0xff>;
+ ranges = <0x81000000 0 0 0x01f80000 0 0x00010000>,
+ <0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
+ num-lanes = <1>;
+ interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &gpc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 2 &gpc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 3 &gpc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 4 &gpc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_PCIE_AXI>,
+ <&clks IMX6QDL_CLK_LVDS1_GATE>,
+ <&clks IMX6QDL_CLK_PCIE_REF_125M>;
+ clock-names = "pcie", "pcie_bus", "pcie_phy";
+ };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index f73fef615702..a1e2cc0be9e8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14187,7 +14187,7 @@ M: Lucas Stach <l.stach@xxxxxxxxxxxxxx>
L: linux-pci@xxxxxxxxxxxxxxx
L: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx (moderated for non-subscribers)
S: Maintained
-F: Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
+F: Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
F: drivers/pci/controller/dwc/*imx6*
PCI DRIVER FOR FU740
--
2.25.1
