[PATCH v3 2/4] remoteproc: Add a remoteproc driver for the MT8183's APU

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This adds a driver to control the APU present in the MT8183.
This loads the firmware and start the DSP.

Signed-off-by: Alexandre Bailon <abailon@xxxxxxxxxxxx>
---
 drivers/remoteproc/Kconfig   |  10 +
 drivers/remoteproc/Makefile  |   1 +
 drivers/remoteproc/mtk_apu.c | 440 +++++++++++++++++++++++++++++++++++
 3 files changed, 451 insertions(+)
 create mode 100644 drivers/remoteproc/mtk_apu.c

diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
index 9a6eedc3994a5..6c106a6c3ad5d 100644
--- a/drivers/remoteproc/Kconfig
+++ b/drivers/remoteproc/Kconfig
@@ -53,6 +53,16 @@ config MTK_SCP
 
 	  It's safe to say N here.
 
+config MTK_APU
+	tristate "Mediatek APU remoteproc support"
+	depends on ARCH_MEDIATEK
+	depends on MTK_IOMMU
+	help
+	  Say y to support the Mediatek's Accelerated Processing Unit (APU) via
+	  the remote processor framework.
+
+	  It's safe to say N here.
+
 config OMAP_REMOTEPROC
 	tristate "OMAP remoteproc support"
 	depends on ARCH_OMAP4 || SOC_OMAP5 || SOC_DRA7XX
diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
index bb26c9e4ef9cf..e395af86c17b0 100644
--- a/drivers/remoteproc/Makefile
+++ b/drivers/remoteproc/Makefile
@@ -14,6 +14,7 @@ obj-$(CONFIG_REMOTEPROC_CDEV)		+= remoteproc_cdev.o
 obj-$(CONFIG_IMX_REMOTEPROC)		+= imx_rproc.o
 obj-$(CONFIG_INGENIC_VPU_RPROC)		+= ingenic_rproc.o
 obj-$(CONFIG_MTK_SCP)			+= mtk_scp.o mtk_scp_ipi.o
+obj-$(CONFIG_MTK_APU)			+= mtk_apu.o
 obj-$(CONFIG_OMAP_REMOTEPROC)		+= omap_remoteproc.o
 obj-$(CONFIG_WKUP_M3_RPROC)		+= wkup_m3_rproc.o
 obj-$(CONFIG_DA8XX_REMOTEPROC)		+= da8xx_remoteproc.o
diff --git a/drivers/remoteproc/mtk_apu.c b/drivers/remoteproc/mtk_apu.c
new file mode 100644
index 0000000000000..0e3f63987bd85
--- /dev/null
+++ b/drivers/remoteproc/mtk_apu.c
@@ -0,0 +1,440 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 BayLibre SAS
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/iommu.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/platform_device.h>
+#include <linux/remoteproc.h>
+
+#include "remoteproc_internal.h"
+
+#define SW_RST					(0x0000000C)
+#define SW_RST_OCD_HALT_ON_RST			BIT(12)
+#define SW_RST_IPU_D_RST			BIT(8)
+#define SW_RST_IPU_B_RST			BIT(4)
+#define CORE_CTRL				(0x00000110)
+#define CORE_CTRL_PDEBUG_ENABLE			BIT(31)
+#define CORE_CTRL_SRAM_64K_iMEM			(0x00 << 27)
+#define CORE_CTRL_SRAM_96K_iMEM			(0x01 << 27)
+#define CORE_CTRL_SRAM_128K_iMEM		(0x02 << 27)
+#define CORE_CTRL_SRAM_192K_iMEM		(0x03 << 27)
+#define CORE_CTRL_SRAM_256K_iMEM		(0x04 << 27)
+#define CORE_CTRL_PBCLK_ENABLE			BIT(26)
+#define CORE_CTRL_RUN_STALL			BIT(23)
+#define CORE_CTRL_STATE_VECTOR_SELECT		BIT(19)
+#define CORE_CTRL_PIF_GATED			BIT(17)
+#define CORE_CTRL_NMI				BIT(0)
+#define CORE_XTENSA_INT				(0x00000114)
+#define CORE_CTL_XTENSA_INT			(0x00000118)
+#define CORE_DEFAULT0				(0x0000013C)
+#define CORE_DEFAULT0_QOS_SWAP_0		(0x00 << 28)
+#define CORE_DEFAULT0_QOS_SWAP_1		(0x01 << 28)
+#define CORE_DEFAULT0_QOS_SWAP_2		(0x02 << 28)
+#define CORE_DEFAULT0_QOS_SWAP_3		(0x03 << 28)
+#define CORE_DEFAULT0_ARUSER_USE_IOMMU		(0x10 << 23)
+#define CORE_DEFAULT0_AWUSER_USE_IOMMU		(0x10 << 18)
+#define CORE_DEFAULT1				(0x00000140)
+#define CORE_DEFAULT0_ARUSER_IDMA_USE_IOMMU	(0x10 << 0)
+#define CORE_DEFAULT0_AWUSER_IDMA_USE_IOMMU	(0x10 << 5)
+#define CORE_XTENSA_ALTRESETVEC			(0x000001F8)
+
+#define RSC_VENDOR_CARVEOUT			(RSC_VENDOR_START + 1)
+
+#define APU_RESET_DELAY				(27)
+
+struct mtk_apu_rproc {
+	struct device *dev;
+	void __iomem *base;
+	int irq;
+	struct clk_bulk_data clks[3];
+	struct list_head mappings;
+};
+
+static int mtk_apu_iommu_map(struct rproc *rproc, struct rproc_mem_entry *entry)
+{
+	struct mtk_apu_rproc *apu_rproc = rproc->priv;
+	struct device *dev = rproc->dev.parent;
+	struct rproc_mem_entry *mapping;
+	struct iommu_domain *domain;
+	int ret;
+	u64 pa;
+
+	mapping = kzalloc(sizeof(*mapping), GFP_KERNEL);
+	if (!mapping)
+		return -ENOMEM;
+
+	if (!entry->va)
+		pa = entry->dma;
+	else
+		pa = rproc_va_to_pa(entry->va);
+
+	if ((strcmp(entry->name, "vdev0vring0") == 0 ||
+		strcmp(entry->name, "vdev0vring1") == 0)) {
+		entry->va = memremap(entry->dma, entry->len, MEMREMAP_WC);
+		if (IS_ERR_OR_NULL(entry->va)) {
+			dev_err(dev, "Unable to map memory region: %pa+%lx\n",
+				&entry->dma, entry->len);
+			ret = PTR_ERR(mapping->va);
+			goto free_mapping;
+		}
+		mapping->va = entry->va;
+	}
+
+	domain = iommu_get_domain_for_dev(dev);
+	ret = iommu_map(domain, entry->da, pa, entry->len, entry->flags);
+	if (ret) {
+		dev_err(dev, "iommu_map failed: %d\n", ret);
+		goto err_memunmap;
+	}
+
+	mapping->da = entry->da;
+	mapping->len = entry->len;
+	list_add_tail(&mapping->node, &apu_rproc->mappings);
+
+	return 0;
+
+err_memunmap:
+	memunmap(mapping->va);
+free_mapping:
+	kfree(mapping);
+
+	return ret;
+}
+
+static void mtk_apu_iommu_unmap_all(struct rproc *rproc)
+{
+	struct mtk_apu_rproc *apu_rproc = rproc->priv;
+	struct device *dev = rproc->dev.parent;
+	struct rproc_mem_entry *entry, *tmp;
+	struct iommu_domain *domain;
+
+	/* clean up iommu mapping entries */
+	list_for_each_entry_safe(entry, tmp, &apu_rproc->mappings, node) {
+		size_t unmapped;
+
+		domain = iommu_get_domain_for_dev(dev);
+		unmapped = iommu_unmap(domain, entry->da, entry->len);
+		if (unmapped != entry->len) {
+			/* nothing much to do besides complaining */
+			dev_err(dev, "failed to unmap %zx/%zu\n", entry->len,
+				unmapped);
+		}
+		memunmap(entry->va);
+
+		list_del(&entry->node);
+		kfree(entry);
+	}
+}
+
+static int mtk_apu_rproc_prepare(struct rproc *rproc)
+{
+	struct mtk_apu_rproc *apu_rproc = rproc->priv;
+	int ret;
+
+	ret = clk_bulk_prepare_enable(ARRAY_SIZE(apu_rproc->clks),
+				      apu_rproc->clks);
+	if (ret)
+		dev_err(apu_rproc->dev, "Failed to enable clocks\n");
+
+	return ret;
+}
+
+static int mtk_apu_rproc_unprepare(struct rproc *rproc)
+{
+	struct mtk_apu_rproc *apu_rproc = rproc->priv;
+
+	clk_bulk_disable_unprepare(ARRAY_SIZE(apu_rproc->clks),
+				   apu_rproc->clks);
+
+	return 0;
+}
+
+static int mtk_apu_rproc_start(struct rproc *rproc)
+{
+	struct mtk_apu_rproc *apu_rproc = rproc->priv;
+	u32 core_ctrl;
+
+	/* Set reset vector of APU firmware boot address */
+	writel(rproc->bootaddr, apu_rproc->base + CORE_XTENSA_ALTRESETVEC);
+
+	/* Turn on the clocks and stall the APU */
+	core_ctrl = readl(apu_rproc->base + CORE_CTRL);
+	core_ctrl |= CORE_CTRL_PDEBUG_ENABLE | CORE_CTRL_PBCLK_ENABLE |
+		     CORE_CTRL_STATE_VECTOR_SELECT | CORE_CTRL_RUN_STALL |
+		     CORE_CTRL_PIF_GATED;
+	writel(core_ctrl, apu_rproc->base + CORE_CTRL);
+
+	/* Reset the APU: this requires 27 ns to be effective on any platform */
+	writel(SW_RST_OCD_HALT_ON_RST | SW_RST_IPU_B_RST | SW_RST_IPU_D_RST,
+		apu_rproc->base + SW_RST);
+	ndelay(APU_RESET_DELAY);
+	writel(0, apu_rproc->base + SW_RST);
+
+	core_ctrl &= ~CORE_CTRL_PIF_GATED;
+	writel(core_ctrl, apu_rproc->base + CORE_CTRL);
+
+	/* Configure memory accesses to go through the IOMMU */
+	writel(CORE_DEFAULT0_AWUSER_USE_IOMMU | CORE_DEFAULT0_ARUSER_USE_IOMMU |
+	      CORE_DEFAULT0_QOS_SWAP_1, apu_rproc->base + CORE_DEFAULT0);
+	writel(CORE_DEFAULT0_AWUSER_IDMA_USE_IOMMU |
+		CORE_DEFAULT0_ARUSER_IDMA_USE_IOMMU,
+		apu_rproc->base + CORE_DEFAULT1);
+
+	/* Release the APU */
+	core_ctrl &= ~CORE_CTRL_RUN_STALL;
+	writel(core_ctrl, apu_rproc->base + CORE_CTRL);
+
+	return 0;
+}
+
+static int mtk_apu_rproc_stop(struct rproc *rproc)
+{
+	struct mtk_apu_rproc *apu_rproc = rproc->priv;
+	u32 core_ctrl;
+
+	core_ctrl = readl(apu_rproc->base + CORE_CTRL);
+	writel(core_ctrl | CORE_CTRL_RUN_STALL, apu_rproc->base + CORE_CTRL);
+
+	mtk_apu_iommu_unmap_all(rproc);
+
+	return 0;
+}
+
+static void mtk_apu_rproc_kick(struct rproc *rproc, int vqid)
+{
+	struct mtk_apu_rproc *apu_rproc = rproc->priv;
+
+	writel(1 << vqid, apu_rproc->base + CORE_CTL_XTENSA_INT);
+}
+
+static int mtk_apu_load(struct rproc *rproc, const struct firmware *fw)
+
+{
+	struct rproc_mem_entry *entry, *tmp;
+	int ret;
+
+	ret = rproc_elf_load_segments(rproc, fw);
+	if (ret)
+		return ret;
+
+	list_for_each_entry_safe(entry, tmp, &rproc->carveouts, node) {
+		ret = mtk_apu_iommu_map(rproc, entry);
+		if (ret)
+			goto err_unmap_all;
+	}
+
+	return 0;
+
+err_unmap_all:
+	mtk_apu_iommu_unmap_all(rproc);
+
+	return ret;
+}
+
+static struct reserved_mem *of_reserved_mem_by_name(struct rproc *rproc,
+						    const char *name)
+{
+	struct device *dev = rproc->dev.parent;
+	struct device_node *np = dev->of_node;
+	struct device_node *target;
+	struct reserved_mem *rmem;
+	int idx;
+
+	idx = of_property_match_string(np, "memory-region-names", name);
+	if (idx < 0) {
+		dev_err(dev, "failed to find %s memory\n", name);
+		return NULL;
+	}
+
+	target = of_parse_phandle(np, "memory-region", idx);
+	if (!target)
+		return NULL;
+
+	rmem = of_reserved_mem_lookup(target);
+	if (!rmem)
+		dev_err(dev, "unable to acquire memory-region\n");
+	of_node_put(target);
+
+	return rmem;
+}
+
+static int mtk_apu_handle_rsc(struct rproc *rproc, u32 rsc_type, void *rsc,
+			      int offset, int avail)
+{
+	struct device *dev = rproc->dev.parent;
+
+	if (rsc_type == RSC_VENDOR_CARVEOUT) {
+		struct fw_rsc_carveout *rsc_carveout = rsc;
+		struct rproc_mem_entry *mem;
+		struct reserved_mem *rmem;
+
+		rmem = of_reserved_mem_by_name(rproc, rsc_carveout->name);
+		if (!rmem)
+			return -ENOMEM;
+
+		if (rmem->size < rsc_carveout->len) {
+			dev_err(dev, "The reserved memory is too small\n");
+			return -ENOMEM;
+		}
+
+		mem = rproc_mem_entry_init(dev, NULL, (dma_addr_t)rmem->base,
+					   rsc_carveout->len, rsc_carveout->da,
+					   NULL, NULL, rsc_carveout->name);
+		if (!mem)
+			return -ENOMEM;
+
+		mem->flags = rsc_carveout->flags;
+		rsc_carveout->pa = rmem->base;
+		rproc_add_carveout(rproc, mem);
+	}
+
+	return RSC_HANDLED;
+}
+
+static const struct rproc_ops mtk_apu_rproc_ops = {
+	.prepare		= mtk_apu_rproc_prepare,
+	.unprepare		= mtk_apu_rproc_unprepare,
+	.start			= mtk_apu_rproc_start,
+	.stop			= mtk_apu_rproc_stop,
+	.kick			= mtk_apu_rproc_kick,
+	.load			= mtk_apu_load,
+	.parse_fw		= rproc_elf_load_rsc_table,
+	.find_loaded_rsc_table	= rproc_elf_find_loaded_rsc_table,
+	.sanity_check		= rproc_elf_sanity_check,
+	.get_boot_addr		= rproc_elf_get_boot_addr,
+	.handle_rsc		= mtk_apu_handle_rsc,
+};
+
+static irqreturn_t mtk_apu_rproc_callback(int irq, void *data)
+{
+	struct rproc *rproc = data;
+	struct mtk_apu_rproc *apu_rproc = (struct mtk_apu_rproc *)rproc->priv;
+
+	writel(1, apu_rproc->base + CORE_XTENSA_INT);
+
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t handle_event(int irq, void *data)
+{
+	struct rproc *rproc = data;
+
+	rproc_vq_interrupt(rproc, 0);
+	rproc_vq_interrupt(rproc, 1);
+
+	return IRQ_HANDLED;
+}
+
+static int mtk_apu_rproc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mtk_apu_rproc *apu_rproc;
+	struct rproc *rproc;
+	struct resource *res;
+	int ret;
+
+	rproc = rproc_alloc(dev, dev_name(dev), &mtk_apu_rproc_ops, NULL,
+			    sizeof(*apu_rproc));
+	if (!rproc)
+		return -ENOMEM;
+
+	rproc->recovery_disabled = true;
+	rproc->has_iommu = false;
+	rproc->auto_boot = false;
+
+	apu_rproc = rproc->priv;
+	apu_rproc->dev = dev;
+	INIT_LIST_HEAD(&apu_rproc->mappings);
+
+	platform_set_drvdata(pdev, rproc);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	apu_rproc->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(apu_rproc->base)) {
+		dev_err(dev, "Failed to map mmio\n");
+		ret = PTR_ERR(apu_rproc->base);
+		goto free_rproc;
+	}
+
+	apu_rproc->irq = platform_get_irq(pdev, 0);
+	if (apu_rproc->irq < 0) {
+		ret = apu_rproc->irq;
+		goto free_rproc;
+	}
+
+	ret = devm_request_threaded_irq(dev, apu_rproc->irq,
+					mtk_apu_rproc_callback, handle_event,
+					IRQF_SHARED | IRQF_ONESHOT,
+					NULL, rproc);
+	if (ret) {
+		dev_err(dev, "devm_request_threaded_irq error: %d\n", ret);
+		goto free_rproc;
+	}
+
+	apu_rproc->clks[0].id = "ipu";
+	apu_rproc->clks[1].id = "axi";
+	apu_rproc->clks[2].id = "jtag";
+
+	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(apu_rproc->clks),
+				apu_rproc->clks);
+	if (ret) {
+		dev_err(dev, "Failed to get clocks\n");
+		goto free_rproc;
+	}
+
+	ret = rproc_add(rproc);
+	if (ret) {
+		dev_err(dev, "rproc_add failed: %d\n", ret);
+		goto free_rproc;
+	}
+
+	return 0;
+
+free_rproc:
+	rproc_free(rproc);
+
+	return ret;
+}
+
+static int mtk_apu_rproc_remove(struct platform_device *pdev)
+{
+	struct rproc *rproc = platform_get_drvdata(pdev);
+	struct mtk_apu_rproc *apu_rproc = (struct mtk_apu_rproc *)rproc->priv;
+	struct device *dev = &pdev->dev;
+
+	disable_irq(apu_rproc->irq);
+
+	rproc_del(rproc);
+	of_reserved_mem_device_release(dev);
+	rproc_free(rproc);
+
+	return 0;
+}
+
+static const struct of_device_id mtk_apu_rproc_of_match[] = {
+	{ .compatible = "mediatek,mt8183-apu", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, mtk_apu_rproc_of_match);
+
+static struct platform_driver mtk_apu_rproc_driver = {
+	.probe = mtk_apu_rproc_probe,
+	.remove = mtk_apu_rproc_remove,
+	.driver = {
+		.name = "mtk_apu-rproc",
+		.of_match_table = of_match_ptr(mtk_apu_rproc_of_match),
+	},
+};
+module_platform_driver(mtk_apu_rproc_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Alexandre Bailon");
+MODULE_DESCRIPTION("MTK APU Remote Processor control driver");
-- 
2.31.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux