On Sun, Aug 15, 2021, at 18:49, Marc Zyngier wrote:
> On Sun, 15 Aug 2021 13:33:14 +0100,
> "Sven Peter" <sven@xxxxxxxxxxxxx> wrote:
> >
> >
> >
> > On Sun, Aug 15, 2021, at 09:42, Marc Zyngier wrote:
> > > On Sun, 15 Aug 2021 05:25:25 +0100,
> > > Alyssa Rosenzweig <alyssa@xxxxxxxxxxxxx> wrote:
> > [...]
> > > > +
> > > > +static int apple_pcie_setup_port(struct apple_pcie *pcie, unsigned int i)
> > > > +{
> > > > + struct fwnode_handle *fwnode = dev_fwnode(pcie->dev);
> > > > + void __iomem *port;
> > > > + struct gpio_desc *reset;
> > > > + uint32_t stat;
> > > > + int ret;
> > > > +
> > > > + port = devm_of_iomap(pcie->dev, to_of_node(fwnode), i + 3, NULL);
> > > > +
> > > > + if (IS_ERR(port))
> > > > + return -ENODEV;
> > > > +
> > > > + reset = devm_gpiod_get_index(pcie->dev, "reset", i, 0);
> > > > + if (IS_ERR(reset))
> > > > + return PTR_ERR(reset);
> > > > +
> > > > + gpiod_direction_output(reset, 0);
> > > > +
> > > > + rmwl(0, PORT_APPCLK_EN, port + PORT_APPCLK);
> > > > +
> > > > + ret = apple_pcie_setup_refclk(pcie->rc, port, i);
> > > > + if (ret < 0)
> > > > + return ret;
> > > > +
> > > > + rmwl(0, PORT_PERST_OFF, port + PORT_PERST);
> > > > + gpiod_set_value(reset, 1);
> > > > +
> > > > + ret = readl_poll_timeout(port + PORT_STATUS, stat,
> > > > + stat & PORT_STATUS_READY, 100, 250000);
> > > > + if (ret < 0) {
> > > > + dev_err(pcie->dev, "port %u ready wait timeout\n", i);
> > > > + return ret;
> > > > + }
> > > > +
> > > > + rmwl(PORT_REFCLK_CGDIS, 0, port + PORT_REFCLK);
> > > > + rmwl(PORT_APPCLK_CGDIS, 0, port + PORT_APPCLK);
> > > > +
> > > > + ret = readl_poll_timeout(port + PORT_LINKSTS, stat,
> > > > + !(stat & PORT_LINKSTS_BUSY), 100, 250000);
> > > > + if (ret < 0) {
> > > > + dev_err(pcie->dev, "port %u link not busy timeout\n", i);
> > > > + return ret;
> > > > + }
> > > > +
> > > > + writel(0xfb512fff, port + PORT_INTMSKSET);
> > >
> > > Magic. What is this for?
> >
> > The magic comes from the original Corellium driver. It first masks everything
> > except for the interrupts in the next line, then acks the interrupts it keeps
> > enabled and then probably wants to wait for PORT_INT_LINK_UP (or any of the
> > other interrupts which seem to indicate various error conditions) to fire but
> > instead polls for PORT_LINKSTS_UP.
> >
> > >
> > > > +
> > > > + writel(PORT_INT_LINK_UP | PORT_INT_LINK_DOWN | PORT_INT_AF_TIMEOUT |
> > > > + PORT_INT_REQADDR_GT32 | PORT_INT_MSI_ERR |
> > > > + PORT_INT_MSI_BAD_DATA | PORT_INT_CPL_ABORT |
> > > > + PORT_INT_CPL_TIMEOUT | (1 << 26), port + PORT_INTSTAT);
> > > > +
> > > > + usleep_range(5000, 10000);
> > > > +
> > > > + rmwl(0, PORT_LTSSMCTL_START, port + PORT_LTSSMCTL);
> > > > +
> > > > + ret = readl_poll_timeout(port + PORT_LINKSTS, stat,
> > > > + stat & PORT_LINKSTS_UP, 100, 500000);
> > > > + if (ret < 0) {
> > > > + dev_err(pcie->dev, "port %u link up wait timeout\n", i);
> > > > + return ret;
> > > > + }
> > >
> > > I have the strong feeling that a lot of things in the above is to get
> > > an interrupt when the port reports an event. Why the polling then?
> >
> >
> > I'm pretty sure this is true. The same registers are also used to setup
> > and handle legacy interrupts.
> >
> > My current understanding is that PORT_INTSTAT is used to retrieve the fired
> > interrupts and ack them, and PORT_INTMSK are the masked interrupts.
> > And then PORT_INTMSKSET and PORT_INTMSKCLR can be used to manipulate
> > individual bits of PORT_INTMSK with a single store.
>
> So this really should be modelled as an interrupt controller. If
> someone comes up with a bit of a spec (though the bit assignment is
> relatively clear), I can update the interrupt code to handle
> that. After all, I moan enough at people writing horrible PCI driver
> code, I might as well write an example myself and point them to it.
Thanks for the offer!
Unfortunately, what I've written above is almost everything I know about this
hardware. If you tell me what additional details you need to know I can see
what I'm able to figure out though and write a small summary.
Thanks,
Sven
