From: Chris Morgan <macromorgan@xxxxxxxxxxx>
Create dt-binding documentation to document rk817 battery and charger
usage. New device-tree properties have been added.
- rockchip,resistor-sense-micro-ohms: The value in microohms of the
sample resistor.
- rockchip,sleep-enter-current-microamp: The value in microamps of the
sleep enter current.
- rockchip,sleep-filter-current: The value in microamps of the sleep
filter current.
Signed-off-by: Chris Morgan <macromorgan@xxxxxxxxxxx>
Signed-off-by: Maya Matuszczyk <maccraft123mc@xxxxxxxxx>
---
.../devicetree/bindings/mfd/rk808.txt | 36 ++++++++++++++++++-
1 file changed, 35 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
index 23a17a6663ec..89b9fa7e10b5 100644
--- a/Documentation/devicetree/bindings/mfd/rk808.txt
+++ b/Documentation/devicetree/bindings/mfd/rk808.txt
@@ -70,13 +70,40 @@ Optional RK817 properties:
- vcc8-supply: The input supply for BOOST
- vcc9-supply: The input supply for OTG_SWITCH
+
- codec: The child node for the codec to hold additional properties.
If no additional properties are required for the codec, this
node can be omitted.
-
- rockchip,mic-in-differential: Telling if the microphone uses differential
mode. Should be under the codec child node.
+- battery: The child node for the charger to hold additional properties.
+ If a battery is not in use, this node can be omitted. If a
+ battery node is used, the following values are required:
+ rockchip,resistor-sense, rockchip,sleep-enter-current,
+ rockchip,sleep-filter-current, and a phandle to a
+ monitored-battery node that contains a valid value for
+ charge-full-design-microamp-hours,
+ charge-term-current-microamp,
+ constant-charge-current-max-microamp,
+ constant-charge-voltage-max-microvolt,
+ voltage-max-design-microvolt, voltage-min-design-microvolt,
+ and a valid ocv-capacity table.
+- rockchip,resistor-sense-micro-ohms: Value in microohms of the battery sense
+ resistor. The PMIC only supports values
+ of either 10000 or 20000. This value is
+ used by the driver to set the correct
+ divisor value to translate ADC readings
+ into the proper units of measure.
+- rockchip,sleep-enter-current-microamp: Value in microamps of the sleep enter
+ current for the charger. Value is used
+ by the driver to calibrate the relax
+ threshold.
+- rockchip,sleep-filter-current-microamp: Value in microamps of the sleep
+ filter current for the charger.
+ Value is used by the driver to derive
+ the sleep sample current.
+
Optional RK818 properties:
- vcc1-supply: The input supply for DCDC_REG1
- vcc2-supply: The input supply for DCDC_REG2
@@ -459,6 +486,13 @@ Example:
};
};
+ rk817_battery: battery {
+ monitored-battery = <&battery_cell>;
+ rockchip,resistor-sense-micro-ohms = <10000>;
+ rockchip,sleep-enter-current-microamp = <300000>;
+ rockchip,sleep-filter-current-microamp = <100000>;
+ };
+
rk817_codec: codec {
rockchip,mic-in-differential;
};
--
2.25.1
