This is a one bay NAS originally shipping Linux 2.6.24.4. It features
- 128 MiB RAM
- 2x eSATA (1x internal, 1x external)
- 2x USB 2.0
- 4 MiB NOR
- battery powered RTC on i2c (PCF8563)
- 1x GBit ethernet
For now only the low-hanging fruits are added to the device tree, eSATA,
USB, i2c and networking needs more work as there are no drivers
available.
Such a machine was offered to me by Richard Fröhning. Thanks!
Signed-off-by: Uwe Kleine-König <uwe@xxxxxxxxxxxxxxxxx>
---
.../devicetree/bindings/arm/oxnas.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/ox810se-zyxel-nsa210.dts | 156 ++++++++++++++++++
3 files changed, 158 insertions(+)
create mode 100644 arch/arm/boot/dts/ox810se-zyxel-nsa210.dts
diff --git a/Documentation/devicetree/bindings/arm/oxnas.txt b/Documentation/devicetree/bindings/arm/oxnas.txt
index ac64e60f99f1..c1529d6c9666 100644
--- a/Documentation/devicetree/bindings/arm/oxnas.txt
+++ b/Documentation/devicetree/bindings/arm/oxnas.txt
@@ -11,4 +11,5 @@ Boards with the OX820 SoC shall have the following properties:
Board compatible values:
- "wd,mbwe" (OX810SE)
+ - "zyxel,nsa210" (OX810SE)
- "cloudengines,pogoplugv3" (OX820)
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 863347b6b65e..720b7d7e342a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -913,6 +913,7 @@ dtb-$(CONFIG_ARCH_PXA) += \
pxa300-raumfeld-speaker-s.dtb
dtb-$(CONFIG_ARCH_OXNAS) += \
ox810se-wd-mbwe.dtb \
+ ox810se-zyxel-nsa210.dtb \
ox820-cloudengines-pogoplug-series-3.dtb
dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8060-dragonboard.dtb \
diff --git a/arch/arm/boot/dts/ox810se-zyxel-nsa210.dts b/arch/arm/boot/dts/ox810se-zyxel-nsa210.dts
new file mode 100644
index 000000000000..88d0e065cf99
--- /dev/null
+++ b/arch/arm/boot/dts/ox810se-zyxel-nsa210.dts
@@ -0,0 +1,156 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Device tree file for Zyxel NSA-210
+ */
+
+/dts-v1/;
+#include "ox810se.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Zyxel NSA-210";
+
+ compatible = "zyxel,nsa210", "oxsemi,ox810se";
+
+ chosen {
+ bootargs = "console=ttyS2,115200n8";
+ };
+
+ memory {
+ reg = <0x48000000 0x8000000>;
+ };
+
+ aliases {
+ serial2 = &uart2;
+ };
+
+ flash@41000000 {
+ compatible = "cfi-flash";
+ reg = <0x41000000 0x00400000>;
+ bank-width = <1>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partitions@0 {
+ label = "uboot";
+ reg = <0x00000000 0x00020000>;
+ };
+
+ partitions@1 {
+ label = "kernel";
+ reg = <0x00020000 0x001c0000>;
+ };
+
+ partitions@2 {
+ label = "initrd";
+ reg = <0x001e0000 0x001a0000>;
+ };
+
+ partitions@3 {
+ label = "etc";
+ reg = <0x00380000 0x00070000>;
+ };
+
+ /* 448k gap */
+
+ partitions@4 {
+ label = "env1";
+ reg = <0x003fc000 0x00002000>;
+ };
+
+ partitions@5 {
+ label = "env2";
+ reg = <0x003fe000 0x00002000>;
+ };
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset";
+ gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+ };
+
+ power {
+ label = "Power";
+ gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
+ };
+
+ sync {
+ label = "Copy/Sync";
+ gpio = <&gpio0 10 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ /*
+ * The vendor U-Boot enables a PWM to make this LED blink during boot.
+ * This must be disabled to be able to drive the LED using the
+ * GPIO as defined here by unsetting bit 9 in the
+ * SYS_CTRL_GPIO_PWMSEL_CTRL_0 register.
+ * E.g. do before starting Linux: mw 0x4500009c 0
+ */
+ led1 {
+ label = "nsa210:green:sys";
+ gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ led2 {
+ label = "nsa210:red:hdd";
+ gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ led3 {
+ label = "nsa210:green:hdd";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+ };
+
+ led4 {
+ label = "nsa210:red:usb";
+ gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ led5 {
+ label = "nsa210:green:usb";
+ gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+ };
+
+ led6 {
+ label = "nsa210:red:esata";
+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ led7 {
+ label = "nsa210:green:esata";
+ gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+ };
+
+ led8 {
+ label = "nsa210:red:copy";
+ gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ led9 {
+ label = "nsa210:green:copy";
+ gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&uart2 {
+ /*
+ * To make this device work as expected bit 2 of register
+ * SYS_CTRL_UART_CTRL must be set. Otherwise the interrupt doesn't
+ * trigger, so console messages make it through, but userspace cannot
+ * make use of it.
+ * E.g. do before starting Linux: mw 0x45000094 4
+ */
+ status = "okay";
+};
--
2.30.2
