On Mon, Jul 19, 2021 at 8:29 PM Stephan Gerhold <stephan@xxxxxxxxxxx> wrote: > > On Mon, Jul 19, 2021 at 07:19:05PM +0300, Andy Shevchenko wrote: > > On Mon, Jul 19, 2021 at 6:11 PM Stephan Gerhold <stephan@xxxxxxxxxxx> wrote: > > > On Mon, Jul 19, 2021 at 06:01:01PM +0300, Andy Shevchenko wrote: > > > > On Mon, Jul 19, 2021 at 5:07 PM Linus Walleij <linus.walleij@xxxxxxxxxx> wrote: > > > > > On Mon, Jul 19, 2021 at 1:26 PM Stephan Gerhold <stephan@xxxxxxxxxxx> wrote: ... > > > > > > #include <linux/acpi.h> > > > > > > +#include <linux/of_irq.h> > > > > > (...) > > > > > > + irq_info = bmc150_accel_interrupts_int1; > > > > > > + if (irq == of_irq_get_byname(dev->of_node, "INT2")) > > > > > > + irq_info = bmc150_accel_interrupts_int2; > > > > > > > > > > This looks a bit DT-specific, but I don't see that ACPI has > > > > > named IRQs so I don't know what to do about it either. > > > > > > > > Yeah, we only have so far the (de facto) established way of naming > > > > GPIO based IRQs, and not IOxAPIC ones. > > > > > > > > > What does platform_get_irq_byname() do on ACPI systems? > > > > > > > > See above. > > > > > > > > > If there is no obvious fix I would leave it like this until the > > > > > first ACPI used needing this comes along, but I think maybe > > > > > Andy has suggestions. > > > > > > > > The platform_get_irq_byname() should do something similar that has > > > > been done in platform_get_irq() WRT ACPI. > > > > Here for sure the platform_get_irq_byname() or its optional variant > > > > should be used. > > > > > > I don't think there is a platform device here, we only have the > > > i2c_client or spi_device. That's why I didn't use > > > platform_get_irq_byname(). :) > > > > > > Is there something equivalent for I2C/SPI drivers? > > > > Not yet. You probably need to supply some code there to allow > > multi-IRQ devices (in resource provider agnostic way). > > > > You need to provide fwnode_get_irq_byname() to be similar with > > https://elixir.bootlin.com/linux/latest/source/drivers/base/property.c#L1010 > > > > Then use it in the drivers. > > > > And/or integrate into frameworks somehow (something in between the > > lines: https://elixir.bootlin.com/linux/latest/source/drivers/i2c/i2c-core-base.c#L461). > > > > Well, I don't think anyone has an ACPI use case for this right now so > it's probably better if this is done by someone who actually needs this > and can test it somewhere. :) > > I actually just "copied" this approach from some other IIO drivers where > this is done similarly (and additionally checked the source code to make > sure this won't break anything for ACPI platforms). I see in today's Linux Next snapshot: drivers/iio/accel/fxls8962af-core.c:774: irq = of_irq_get_byname(of_node, "INT2"); drivers/iio/accel/mma8452.c:1616: irq2 = of_irq_get_byname(client->dev.of_node, "INT2"); drivers/iio/gyro/fxas21002c_core.c:834: irq1 = of_irq_get_byname(np, "INT1"); drivers/iio/imu/adis16480.c:1265: irq = of_irq_get_byname(of_node, adis16480_int_pin_names[i]); drivers/iio/imu/bmi160/bmi160_core.c:655: irq = of_irq_get_byname(of_node, "INT1"); drivers/iio/imu/bmi160/bmi160_core.c:661: irq = of_irq_get_byname(of_node, "INT2"); I believe we may stop distributing this and actually start using a common API. I don't want this to be spread again over all IIO. Btw, I have LSM9DS0, which supports two INT pins for IMU and currently it uses hard coded pin mapping. Side note to Jonathan, I believe the below may be (lazily) converted to fwnode / device properties APIs. drivers/iio/adc/ab8500-gpadc.c:1041: nchans = of_get_available_child_count(np); drivers/iio/adc/ad7124.c:747: st->num_channels = of_get_available_child_count(np); drivers/iio/adc/berlin2-adc.c:287: struct device_node *parent_np = of_get_parent(pdev->dev.of_node); drivers/iio/adc/qcom-pm8xxx-xoadc.c:830: adc->nchans = of_get_available_child_count(np); drivers/iio/adc/qcom-spmi-adc5.c:650: channel_name = of_get_property(node, drivers/iio/adc/qcom-spmi-adc5.c:813: adc->nchannels = of_get_available_child_count(node); drivers/iio/adc/qcom-spmi-vadc.c:743: vadc->nchannels = of_get_available_child_count(node); drivers/iio/adc/stm32-adc.c:1630:static int stm32_adc_of_get_resolution(struct iio_dev *indio_dev) drivers/iio/adc/stm32-adc.c:1935: ret = stm32_adc_of_get_resolution(indio_dev); drivers/iio/adc/xilinx-xadc-core.c:1248: chan_node = of_get_child_by_name(np, "xlnx,channels"); drivers/iio/imu/adis16480.c:1293:static int adis16480_of_get_ext_clk_pin(struct adis16480 *st, drivers/iio/imu/adis16480.c:1328: pin = adis16480_of_get_ext_clk_pin(st, of_node); drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c:68: mux_node = of_get_child_by_name(dev->of_node, "i2c-gate") ; drivers/iio/industrialio-core.c:1877: label = of_get_property(indio_dev->dev.of_node, "label", NULL); drivers/iio/inkern.c:228: if (np && !of_get_property(np, "io-channel-ranges", NULL)) drivers/iio/temperature/ltc2983.c:1275: st->num_channels = of_get_available_child_count(dev->of_node); -- With Best Regards, Andy Shevchenko
