Em Tue, 13 Jul 2021 20:26:49 -0600 Rob Herring <robh@xxxxxxxxxx> escreveu: > On Tue, Jul 13, 2021 at 08:28:35AM +0200, Mauro Carvalho Chehab wrote: > > + reset-gpios: > > + description: PCI PERST reset GPIOs > > + maxItems: 4 > > Hiding the 4 ports in the phy? Rob, I'm not trying to hide anything. There are several differences with regards to how PERST# is handled between HiKey 960 and HiKey 970. >From hardware perspective, you can see the schematics of both boards: https://github.com/96boards/documentation/raw/master/consumer/hikey/hikey960/hardware-docs/HiKey960_SoC_Reference_Manual.pdf https://www.96boards.org/documentation/consumer/hikey/hikey970/hardware-docs/files/hikey970-schematics.pdf The 960 PHY has the SoC directly connected to a PCIE M.2 slot (model 10130616) without any external bridge chipset. It uses a single GPIO (GPIO 089) for the PERST# signal, connected via a voltage converter (from 1.8V to 3.3V). $ lspci 00:00.0 PCI bridge: Huawei Technologies Co., Ltd. Device 3660 (rev 01) The 970 PHY has an external PCI bridge chipset (PLX Technology PEX 8606). Besides the bridge, the hardware comes with an Ethernet PCI adapter, a M.2 slot and a mini-PCIe connector. Each one with its own PERST# signal, mapped to different GPIO pins, and each one using its own voltage converter. $ lspci 00:00.0 PCI bridge: Huawei Technologies Co., Ltd. Device 3670 (rev 01) 01:00.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 02:01.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 02:04.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 02:05.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 02:07.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 02:09.0 PCI bridge: PLX Technology, Inc. PEX 8606 6 Lane, 6 Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 07) On other words, there are 4 GPIOs mapped to different PERST# pins in the hardware: - GPIO 56 is connected to the PERST# pin at PEX 8606; - GPIO 25 is connected to the PERST# pin at the M.2 slot; - GPIO 220 is connected to the PERST# pin at the PCIe mini slot; - GPIO 203 is connected to the PERST# pin at the Ethernet chipset. Maybe due to different electrical requirements, the hardware design use different GPIOs instead of feeding them altogether. Anyway, the fact is that the PHY on 970 has 4 different GPIOs that are need in order for the hardware to work. and this is specific to this particular PHY. Now, from software perspective, the power on sequence on Hikey 960 finishes sending PERST# signal to the M.2 slot: static int hi3660_pcie_phy_power_on(struct phy *generic_phy) { ... /* perst assert Endpoint */ if (!gpio_request(phy->gpio_id_reset, "pcie_perst")) { usleep_range(REF_2_PERST_MIN, REF_2_PERST_MAX); ret = gpio_direction_output(phy->gpio_id_reset, 1); if (ret) goto disable_clks; usleep_range(PERST_2_ACCESS_MIN, PERST_2_ACCESS_MAX); return 0; } disable_clks: kirin_pcie_clk_ctrl(phy, false); return ret; } The 970 PHY, however, sends PERST# signal in the middle of the power on sequence, as, after sending reset, it needs to wait for the hardware to stabilize, in order to setup an eye diagram at the PHY: static int hi3670_pcie_phy_power_on(struct phy *generic_phy) { ... /* perst assert Endpoints */ usleep_range(21000, 23000); for (i = 0; i < phy->n_gpio_resets; i++) { ret = gpio_direction_output(phy->gpio_id_reset[i], 1); if (ret) return ret; } usleep_range(10000, 11000); ret = is_pipe_clk_stable(phy); if (!ret) goto disable_clks; hi3670_pcie_set_eyeparam(phy); ret = hi3670_pcie_noc_power(phy, false); if (ret) goto disable_clks; return 0; disable_clks: kirin_pcie_clk_ctrl(phy, false); return ret; } IMO, it makes a lot more sense to map this on DT as part of the PHY and not as part of the PCIe, but no matter how it is mapped, this PHY still requires 4 GPIOs for PERST#. Thanks, Mauro
