Renesas 8T49N241 has 4 outputs, 1 integral and 3 fractional dividers. The 8T49N241 accepts up to two differential or single-ended input clocks and a fundamental-mode crystal input. The internal PLL can lock to either of the input reference clocks or to the crystal to behave as a frequency synthesizer. Signed-off-by: Alex Helms <alexander.helms.jy@xxxxxxxxxxx> --- .../bindings/clock/renesas,8t49n241.yaml | 190 ++++++++++++++++++ MAINTAINERS | 6 + 2 files changed, 196 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/renesas,8t49n241.yaml diff --git a/Documentation/devicetree/bindings/clock/renesas,8t49n241.yaml b/Documentation/devicetree/bindings/clock/renesas,8t49n241.yaml new file mode 100644 index 000000000..586dd6f5c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,8t49n241.yaml @@ -0,0 +1,190 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/renesas,8t49n241.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Binding for Renesas 8T49N241 Universal Frequency Translator + +description: | + The 8T49N241 has one fractional-feedback PLL that can be used as a + jitter attenuator and frequency translator. It is equipped with one + integer and three fractional output dividers, allowing the generation + of up to four different output frequencies, ranging from 8kHz to 1GHz. + These frequencies are completely independent of each other, the input + reference frequencies and the crystal reference frequency. The device + places virtually no constraints on input to output frequency conversion, + supporting all FEC rates, including the new revision of ITU-T + Recommendation G.709 (2009), most with 0ppm conversion error. + The outputs may select among LVPECL, LVDS, HCSL or LVCMOS output levels. + + The driver can read a full register map from the DT, and will use that + register map to initialize the attached part (via I2C) when the system + boots. Any configuration not supported by the common clock framework + must be done via the full register map, including optimized settings. + + The 8T49N241 accepts up to two differential or single-ended input clocks + and a fundamental-mode crystal input. The internal PLL can lock to either + of the input reference clocks or just to the crystal to behave as a + frequency synthesizer. The PLL can use the second input for redundant + backup of the primary input reference, but in this case, both input clock + references must be related in frequency. + + All outputs are currently assumed to be LVDS, unless overridden in the + full register map in the DT. + +maintainers: + - Alex Helms <alexander.helms.jy@xxxxxxxxxxx> + - David Cater <david.cater.jc@xxxxxxxxxxx> + +properties: + compatible: + enum: + - renesas,8t49n241 + + reg: + description: I2C device address + enum: [ 0x7c, 0x6c, 0x7d, 0x6d, 0x7e, 0x6e, 0x7f, 0x6f ] + + '#clock-cells': + const: 1 + + clock-names: + minItems: 1 + maxItems: 3 + items: + enum: [ xtal, clk0, clk1 ] + + clocks: + minItems: 1 + maxItems: 3 + + renesas,settings: + description: Optional, complete register map of the device. + Optimized settings for the device must be provided in full + and are written during initialization. + $ref: /schemas/types.yaml#/definitions/uint8-array + minItems: 791 + maxItems: 791 + +required: + - compatible + - reg + - '#clock-cells' + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + /* 25MHz reference clock */ + clk0: clk0 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + }; + + i2c@0 { + reg = <0x0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + + renesas8t49n241_1: clock-generator@6c { + compatible = "renesas,8t49n241"; + reg = <0x6c>; + #clock-cells = <1>; + + clocks = <&clk0>; + clock-names = "clk0"; + }; + }; + + /* Consumer referencing the 8T49N241 Q1 */ + consumer { + /* ... */ + clocks = <&renesas8t49n241_1 1>; + /* ... */ + }; + - | + /* 40MHz crystal */ + xtal: xtal { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <40000000>; + }; + + i2c@0 { + reg = <0x0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + + renesas8t49n241_2: clock-generator@6c { + compatible = "renesas,8t49n241"; + reg = <0x6c>; + #clock-cells = <1>; + + clocks = <&xtal>; + clock-names = "xtal"; + + renesas,settings=[ + 09 50 00 60 67 C5 6C FF 03 00 30 00 00 01 00 00 + 01 07 00 00 07 00 00 77 6D 06 00 00 00 00 00 FF + FF FF FF 00 3F 00 2A 00 16 33 33 00 01 00 00 D0 + 00 00 00 00 00 00 00 00 00 04 00 00 00 02 00 00 + 00 00 00 00 00 00 00 17 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 D7 0A 2B 20 00 00 00 0B + 00 00 00 00 00 00 00 00 00 00 27 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + C3 00 08 01 00 00 00 00 00 00 00 00 00 30 00 00 + 00 0A 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 85 00 00 9C 01 D4 02 71 07 00 00 00 + 00 83 00 10 02 08 8C + ]; + }; + }; + + /* Consumer referencing the 8T49N241 Q1 */ + consumer { + /* ... */ + clocks = <&renesas8t49n241_2 1>; + /* ... */ + }; diff --git a/MAINTAINERS b/MAINTAINERS index 0cce91cd5..882d79ead 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -15575,6 +15575,12 @@ F: include/linux/rpmsg/ F: include/uapi/linux/rpmsg.h F: samples/rpmsg/ +RENESAS 8T49N24X DRIVER +M: Alex Helms <alexander.helms.jy@xxxxxxxxxxx> +M: David Cater <david.cater.jc@xxxxxxxxxxx> +S: Odd Fixes +F: Documentation/devicetree/bindings/clock/renesas,8t49n241.yaml + RENESAS CLOCK DRIVERS M: Geert Uytterhoeven <geert+renesas@xxxxxxxxx> L: linux-renesas-soc@xxxxxxxxxxxxxxx -- 2.30.2
