Hi,
Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx> writes:
> Wesley Cheng wrote:
>> Some devices have USB compositions which may require multiple endpoints
>> that support EP bursting. HW defined TX FIFO sizes may not always be
>> sufficient for these compositions. By utilizing flexible TX FIFO
>> allocation, this allows for endpoints to request the required FIFO depth to
>> achieve higher bandwidth. With some higher bMaxBurst configurations, using
>> a larger TX FIFO size results in better TX throughput.
>>
>> By introducing the check_config() callback, the resizing logic can fetch
>> the maximum number of endpoints used in the USB composition (can contain
>> multiple configurations), which helps ensure that the resizing logic can
>> fulfill the configuration(s), or return an error to the gadget layer
>> otherwise during bind time.
>>
>> Signed-off-by: Wesley Cheng <wcheng@xxxxxxxxxxxxxx>
>> ---
>> drivers/usb/dwc3/core.c | 15 +++
>> drivers/usb/dwc3/core.h | 16 ++++
>> drivers/usb/dwc3/ep0.c | 2 +
>> drivers/usb/dwc3/gadget.c | 232 ++++++++++++++++++++++++++++++++++++++++++++++
>> 4 files changed, 265 insertions(+)
>>
>> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
>> index ba74ad7..b194aecd 100644
>> --- a/drivers/usb/dwc3/core.c
>> +++ b/drivers/usb/dwc3/core.c
>> @@ -1267,6 +1267,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
>> u8 rx_max_burst_prd;
>> u8 tx_thr_num_pkt_prd;
>> u8 tx_max_burst_prd;
>> + u8 tx_fifo_resize_max_num;
>> const char *usb_psy_name;
>> int ret;
>>
>> @@ -1282,6 +1283,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
>> */
>> hird_threshold = 12;
>>
>> + /*
>> + * default to a TXFIFO size large enough to fit 6 max packets. This
>> + * allows for systems with larger bus latencies to have some headroom
>> + * for endpoints that have a large bMaxBurst value.
>> + */
>> + tx_fifo_resize_max_num = 6;
>> +
>> dwc->maximum_speed = usb_get_maximum_speed(dev);
>> dwc->max_ssp_rate = usb_get_maximum_ssp_rate(dev);
>> dwc->dr_mode = usb_get_dr_mode(dev);
>> @@ -1325,6 +1333,11 @@ static void dwc3_get_properties(struct dwc3 *dwc)
>> &tx_thr_num_pkt_prd);
>> device_property_read_u8(dev, "snps,tx-max-burst-prd",
>> &tx_max_burst_prd);
>> + dwc->do_fifo_resize = device_property_read_bool(dev,
>> + "tx-fifo-resize");
>> + if (dwc->do_fifo_resize)
>> + device_property_read_u8(dev, "tx-fifo-max-num",
>> + &tx_fifo_resize_max_num);
>
> Why is this check here? The dwc->tx_fifo_resize_max_num should store
> whatever property the user sets. Whether the driver wants to use this
Ack!
> property should depend on "dwc->do_fifo_resize". Also why don't we have
> "snps," prefix to be consistent with the other properties?
Ack!
> Can we enforce to a single property? If the designer wants to enable
> this feature, he/she can to provide the tx-fifo-max-num. This would
> simplify the driver a bit. Since this is to optimize for performance,
> the user should know/want/test the specific value if they want to set
> for their setup and not hoping that the default setting not break their
> setup. So we can remove the "do_fifo_resize" property and just check
> whether tx_fifo_resize_max_num is set.
Ack!
All very valid points :-)
>> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
>> index dccdf13..735e9be 100644
>> --- a/drivers/usb/dwc3/core.h
>> +++ b/drivers/usb/dwc3/core.h
>> @@ -1023,6 +1023,7 @@ struct dwc3_scratchpad_array {
>> * @rx_max_burst_prd: max periodic ESS receive burst size
>> * @tx_thr_num_pkt_prd: periodic ESS transmit packet count
>> * @tx_max_burst_prd: max periodic ESS transmit burst size
>> + * @tx_fifo_resize_max_num: max number of fifos allocated during txfifo resize
>> * @hsphy_interface: "utmi" or "ulpi"
>> * @connected: true when we're connected to a host, false otherwise
>> * @delayed_status: true when gadget driver asks for delayed status
>> @@ -1037,6 +1038,7 @@ struct dwc3_scratchpad_array {
>> * 1 - utmi_l1_suspend_n
>> * @is_fpga: true when we are using the FPGA board
>> * @pending_events: true when we have pending IRQs to be handled
>> + * @do_fifo_resize: true when txfifo resizing is enabled for dwc3 endpoints
>> * @pullups_connected: true when Run/Stop bit is set
>> * @setup_packet_pending: true when there's a Setup Packet in FIFO. Workaround
>> * @three_stage_setup: set if we perform a three phase setup
>> @@ -1079,6 +1081,11 @@ struct dwc3_scratchpad_array {
>> * @dis_split_quirk: set to disable split boundary.
>> * @imod_interval: set the interrupt moderation interval in 250ns
>> * increments or 0 to disable.
>> + * @max_cfg_eps: current max number of IN eps used across all USB configs.
>> + * @last_fifo_depth: last fifo depth used to determine next fifo ram start
>> + * address.
>> + * @num_ep_resized: carries the current number endpoints which have had its tx
>> + * fifo resized.
>> */
>> struct dwc3 {
>> struct work_struct drd_work;
>> @@ -1233,6 +1240,7 @@ struct dwc3 {
>> u8 rx_max_burst_prd;
>> u8 tx_thr_num_pkt_prd;
>> u8 tx_max_burst_prd;
>> + u8 tx_fifo_resize_max_num;
>>
>> const char *hsphy_interface;
>>
>> @@ -1246,6 +1254,7 @@ struct dwc3 {
>> unsigned is_utmi_l1_suspend:1;
>> unsigned is_fpga:1;
>> unsigned pending_events:1;
>> + unsigned do_fifo_resize:1;
>> unsigned pullups_connected:1;
>> unsigned setup_packet_pending:1;
>> unsigned three_stage_setup:1;
>> @@ -1281,6 +1290,10 @@ struct dwc3 {
>> unsigned dis_split_quirk:1;
>>
>> u16 imod_interval;
>> +
>> + int max_cfg_eps;
>> + int last_fifo_depth;
>> + int num_ep_resized;
>> };
>>
>> #define INCRX_BURST_MODE 0
>> @@ -1512,6 +1525,7 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
>> struct dwc3_gadget_ep_cmd_params *params);
>> int dwc3_send_gadget_generic_command(struct dwc3 *dwc, unsigned int cmd,
>> u32 param);
>> +void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc);
>> #else
>> static inline int dwc3_gadget_init(struct dwc3 *dwc)
>> { return 0; }
>> @@ -1531,6 +1545,8 @@ static inline int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
>> static inline int dwc3_send_gadget_generic_command(struct dwc3 *dwc,
>> int cmd, u32 param)
>> { return 0; }
>> +static inline void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
>> +{ }
>> #endif
>>
>> #if IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
>> diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c
>> index 3cd2942..d28d085 100644
>> --- a/drivers/usb/dwc3/ep0.c
>> +++ b/drivers/usb/dwc3/ep0.c
>> @@ -619,6 +619,8 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)
>> return -EINVAL;
>>
>> case USB_STATE_ADDRESS:
>> + dwc3_gadget_clear_tx_fifos(dwc);
>> +
>> ret = dwc3_ep0_delegate_req(dwc, ctrl);
>> /* if the cfg matches and the cfg is non zero */
>> if (cfg && (!ret || (ret == USB_GADGET_DELAYED_STATUS))) {
>> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
>> index af6d7f1..e56f1a6 100644
>> --- a/drivers/usb/dwc3/gadget.c
>> +++ b/drivers/usb/dwc3/gadget.c
>> @@ -632,6 +632,187 @@ static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
>> bool interrupt);
>>
>> /**
>> + * dwc3_gadget_calc_tx_fifo_size - calculates the txfifo size value
>> + * @dwc: pointer to the DWC3 context
>> + * @nfifos: number of fifos to calculate for
>> + *
>> + * Calculates the size value based on the equation below:
>> + *
>> + * DWC3 revision 280A and prior:
>> + * fifo_size = mult * (max_packet / mdwidth) + 1;
>> + *
>> + * DWC3 revision 290A and onwards:
>> + * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
>> + *
>> + * The max packet size is set to 1024, as the txfifo requirements mainly apply
>> + * to super speed USB use cases. However, it is safe to overestimate the fifo
>> + * allocations for other scenarios, i.e. high speed USB.
>> + */
>> +static int dwc3_gadget_calc_tx_fifo_size(struct dwc3 *dwc, int mult)
>> +{
>> + int max_packet = 1024;
>> + int fifo_size;
>> + int mdwidth;
>> +
>> + mdwidth = dwc3_mdwidth(dwc);
>> +
>> + /* MDWIDTH is represented in bits, we need it in bytes */
>> + mdwidth >>= 3;
>> +
>> + if (DWC3_VER_IS_PRIOR(DWC3, 290A))
>> + fifo_size = mult * (max_packet / mdwidth) + 1;
>> + else
>> + fifo_size = mult * ((max_packet + mdwidth) / mdwidth) + 1;
>> + return fifo_size;
>> +}
>> +
>> +/**
>> + * dwc3_gadget_clear_tx_fifo_size - Clears txfifo allocation
>> + * @dwc: pointer to the DWC3 context
>> + *
>> + * Iterates through all the endpoint registers and clears the previous txfifo
>> + * allocations.
>> + */
>> +void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
>> +{
>> + struct dwc3_ep *dep;
>> + int fifo_depth;
>> + int size;
>> + int num;
>> +
>> + if (!dwc->do_fifo_resize)
>> + return;
>> +
>> + /* Read ep0IN related TXFIFO size */
>> + dep = dwc->eps[1];
>> + size = dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(0));
>> + if (DWC3_IP_IS(DWC3))
>> + fifo_depth = DWC3_GTXFIFOSIZ_TXFDEP(size);
>> + else
>> + fifo_depth = DWC31_GTXFIFOSIZ_TXFDEP(size);
>> +
>> + dwc->last_fifo_depth = fifo_depth;
>> + /* Clear existing TXFIFO for all IN eps except ep0 */
>> + for (num = 3; num < min_t(int, dwc->num_eps, DWC3_ENDPOINTS_NUM);
>> + num += 2) {
>> + dep = dwc->eps[num];
>> + /* Don't change TXFRAMNUM on usb31 version */
>> + size = DWC3_IP_IS(DWC3) ? 0 :
>> + dwc3_readl(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1)) &
>> + DWC31_GTXFIFOSIZ_TXFRAMNUM;
>> +
>> + dwc3_writel(dwc->regs, DWC3_GTXFIFOSIZ(num >> 1), size);
>> + }
>> + dwc->num_ep_resized = 0;
>> +}
>> +
>> +/*
>> + * dwc3_gadget_resize_tx_fifos - reallocate fifo spaces for current use-case
>> + * @dwc: pointer to our context structure
>> + *
>> + * This function will a best effort FIFO allocation in order
>> + * to improve FIFO usage and throughput, while still allowing
>> + * us to enable as many endpoints as possible.
>> + *
>> + * Keep in mind that this operation will be highly dependent
>> + * on the configured size for RAM1 - which contains TxFifo -,
>> + * the amount of endpoints enabled on coreConsultant tool, and
>> + * the width of the Master Bus.
>> + *
>> + * In general, FIFO depths are represented with the following equation:
>> + *
>> + * fifo_size = mult * ((max_packet + mdwidth)/mdwidth + 1) + 1
>> + *
>> + * In conjunction with dwc3_gadget_check_config(), this resizing logic will
>> + * ensure that all endpoints will have enough internal memory for one max
>> + * packet per endpoint.
>> + */
>> +static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep)
>> +{
>> + struct dwc3 *dwc = dep->dwc;
>> + int fifo_0_start;
>> + int ram1_depth;
>> + int fifo_size;
>> + int min_depth;
>> + int num_in_ep;
>> + int remaining;
>> + int num_fifos = 1;
>> + int fifo;
>> + int tmp;
>> +
>> + if (!dwc->do_fifo_resize)
>> + return 0;
>> +
>> + /* resize IN endpoints except ep0 */
>> + if (!usb_endpoint_dir_in(dep->endpoint.desc) || dep->number <= 1)
>> + return 0;
>
>> +
>> + ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
>> +
>> + if ((dep->endpoint.maxburst > 1 &&
>> + usb_endpoint_xfer_bulk(dep->endpoint.desc)) ||
>> + usb_endpoint_xfer_isoc(dep->endpoint.desc))
>> + num_fifos = 3;
>> +
>> + if (dep->endpoint.maxburst > 6 &&
>> + usb_endpoint_xfer_bulk(dep->endpoint.desc) && DWC3_IP_IS(DWC31))
>> + num_fifos = dwc->tx_fifo_resize_max_num;
>
> Why only bulk? Isoc should be at least equal or more than bulk.
> Also, make this applicable to DWC_usb32 also.
this should be applicable to all DWC3 versions, no? dwc3, 31 and 32.
>> @@ -648,6 +829,10 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)
>> int ret;
>>
>> if (!(dep->flags & DWC3_EP_ENABLED)) {
>> + ret = dwc3_gadget_resize_tx_fifos(dep);
>> + if (ret)
>> + return ret;
>> +
>> ret = dwc3_gadget_start_config(dep);
>> if (ret)
>> return ret;
>> @@ -2498,6 +2683,7 @@ static int dwc3_gadget_stop(struct usb_gadget *g)
>>
>> spin_lock_irqsave(&dwc->lock, flags);
>> dwc->gadget_driver = NULL;
>> + dwc->max_cfg_eps = 0;
>> spin_unlock_irqrestore(&dwc->lock, flags);
>>
>> free_irq(dwc->irq_gadget, dwc->ev_buf);
>> @@ -2585,6 +2771,51 @@ static int dwc3_gadget_vbus_draw(struct usb_gadget *g, unsigned int mA)
>> return ret;
>> }
>>
>> +/**
>> + * dwc3_gadget_check_config - ensure dwc3 can support the USB configuration
>> + * @g: pointer to the USB gadget
>> + *
>> + * Used to record the maximum number of endpoints being used in a USB composite
>> + * device. (across all configurations) This is to be used in the calculation
>> + * of the TXFIFO sizes when resizing internal memory for individual endpoints.
>> + * It will help ensured that the resizing logic reserves enough space for at
>> + * least one max packet.
>> + */
>> +static int dwc3_gadget_check_config(struct usb_gadget *g)
Might be better to pass the actual config being used. And, instead of
check_config, perhaps validate_config is a little more fitting.
--
balbi
Attachment:
signature.asc
Description: PGP signature
