Re: [PATCH v5 0/3] Add Qualcomm PCIe Endpoint driver support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Jun 29, 2021 at 9:47 PM Manivannan Sadhasivam
<manivannan.sadhasivam@xxxxxxxxxx> wrote:
>
> Hello,
>
> This series adds support for Qualcomm PCIe Endpoint controller found
> in platforms like SDX55. The Endpoint controller is based on the designware
> core with additional Qualcomm wrappers around the core.
>
> The driver is added separately unlike other Designware based drivers that
> combine RC and EP in a single driver. This is done to avoid complexity and
> to maintain this driver autonomously.
>
> The driver has been validated with an out of tree MHI function driver on
> SDX55 based Telit FN980 EVB connected to x86 host machine over PCIe.
>
> Thanks,
> Mani
>
> Changes in v5:
>
> * Removed the DBI register settings that are not needed
> * Used the standard definitions available in pci_regs.h
> * Added defines for all the register fields
> * Removed the left over code from previous iteration
>
> Changes in v4:
>
> * Removed the active_config settings needed for IPA integration
> * Switched to writel for couple of relaxed versions that sneaked in

I thought we resolved this discussion. Use _relaxed variants unless
you need the stronger ones.

Rob

>
> Changes in v3:
>
> * Lot of minor cleanups to the driver patch based on review from Bjorn and Stan.
> * Noticeable changes are:
>   - Got rid of _relaxed calls and used readl/writel
>   - Got rid of separate TCSR memory region and used syscon for getting the
>     register offsets for Perst registers
>   - Changed the wake gpio handling logic
>   - Added remove() callback and removed "suppress_bind_attrs"
>   - stop_link() callback now just disables PERST IRQ
> * Added MMIO region and doorbell interrupt to the binding
> * Added logic to write MMIO physicall address to MHI base address as it is
>   for the function driver to work
>
> Changes in v2:
>
> * Addressed the comments from Rob on bindings patch
> * Modified the driver as per binding change
> * Fixed the warnings reported by Kbuild bot
> * Removed the PERST# "enable_irq" call from probe()
>
> Manivannan Sadhasivam (3):
>   dt-bindings: pci: Add devicetree binding for Qualcomm PCIe EP
>     controller
>   PCI: dwc: Add Qualcomm PCIe Endpoint controller driver
>   MAINTAINERS: Add entry for Qualcomm PCIe Endpoint driver and binding
>
>  .../devicetree/bindings/pci/qcom,pcie-ep.yaml | 160 ++++
>  MAINTAINERS                                   |  10 +-
>  drivers/pci/controller/dwc/Kconfig            |  10 +
>  drivers/pci/controller/dwc/Makefile           |   1 +
>  drivers/pci/controller/dwc/pcie-qcom-ep.c     | 742 ++++++++++++++++++
>  5 files changed, 922 insertions(+), 1 deletion(-)
>  create mode 100644 Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
>  create mode 100644 drivers/pci/controller/dwc/pcie-qcom-ep.c
>
> --
> 2.25.1
>



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux