Hello, > From: Konstantin Porotchkin <kostap@xxxxxxxxxxx> > > This patch series contains the following changes/fixes: > 1. Add support for Armada CN913x Development Board topology "B" > 2. Add support for Armada CN913x Reference Design boards (CRB) > 3. Fixes the CP11X references in PHY binding document > 4. Fixes the NAND paritioninig scheme in DTS eliminating gap between > consecutive partitions > All above changes are already intergated into Marvell official SDK sources > > v2: > - extract common nodes from DB boards to separate DTSI files > - disable eth2 on CRB boards until the required phy mode support is added > - mention the switch part ID in CRB board description > > v3: > - do not rename setup A DTS files for DB variants > - fix a couple of wrong include names > > v4: > - Rebase on top of Linus master branch (v5.11-rc7) > - Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC) > - Add cd-gpio entry to CP0 SDHCI for SD card support > - Add a comment to CN9130-CRB patch about the required defconfig > changes for supporting the onboard i2c expander > - Add Stefan's patch to enable 10G port on CN9130-DB platforms > > Grzegorz Jaszczyk (1): > Documentation/bindings: phy: update references to cp11x > > Konstantin Porotchkin (3): > arch/arm64/boot/dts/marvell: fix NAND partitioning scheme > arm64: dts: cn913x: add device trees for topology B boards > arm64: dts: add support for Marvell cn9130-crb platform > > Stefan Chulski (1): > dts: marvell: Enable 10G interface on 9130-DB board > I've applied patches 1 and 2, but I have issue with patch 3, there was some changes around the phys and I am not sure of the correct way to modify the patch. Could you rebase it on v5.13-c1 and fix the merge issue ? Thanks, Gregory > .../bindings/phy/phy-mvebu-comphy.txt | 12 +- > arch/arm64/boot/dts/marvell/Makefile | 5 + > arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ > arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ > arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++ > arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + > arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +---------------- > arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++ > arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + > arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +-------- > arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++ > arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + > arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +-------- > arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++ > 14 files changed, 1223 insertions(+), 784 deletions(-) > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi > > -- > 2.17.1 > -- Gregory Clement, Bootlin Embedded Linux and Kernel engineering http://bootlin.com
