[PATCH V3 net-next 2/4] net: phy: realtek: add dt property to disable CLKOUT clock

[Joakim Zhang <qiangqing.zhang@xxxxxxx>]

CLKOUT is enabled by default after PHY hardware reset, this patch adds
"realtek,clkout-disable" property for user to disable CLKOUT clock
to save PHY power.

Per RTL8211F guide, a PHY reset should be issued after setting these
bits in PHYCR2 register. After this patch, CLKOUT clock output to be
disabled.

Signed-off-by: Joakim Zhang <qiangqing.zhang@xxxxxxx>
---
 drivers/net/phy/realtek.c | 42 ++++++++++++++++++++++++++++++++++++++-
 1 file changed, 41 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
index 821e85a97367..ca258f2a9613 100644
--- a/drivers/net/phy/realtek.c
+++ b/drivers/net/phy/realtek.c
@@ -8,6 +8,7 @@
  * Copyright (c) 2004 Freescale Semiconductor, Inc.
  */
 #include <linux/bitops.h>
+#include <linux/of.h>
 #include <linux/phy.h>
 #include <linux/module.h>
 #include <linux/delay.h>
@@ -27,6 +28,7 @@
 #define RTL821x_PAGE_SELECT			0x1f
 
 #define RTL8211F_PHYCR1				0x18
+#define RTL8211F_PHYCR2				0x19
 #define RTL8211F_INSR				0x1d
 
 #define RTL8211F_TX_DELAY			BIT(8)
@@ -40,6 +42,8 @@
 #define RTL8211E_TX_DELAY			BIT(12)
 #define RTL8211E_RX_DELAY			BIT(11)
 
+#define RTL8211F_CLKOUT_EN			BIT(0)
+
 #define RTL8201F_ISR				0x1e
 #define RTL8201F_ISR_ANERR			BIT(15)
 #define RTL8201F_ISR_DUPLEX			BIT(13)
@@ -71,6 +75,10 @@ MODULE_DESCRIPTION("Realtek PHY driver");
 MODULE_AUTHOR("Johnson Leung");
 MODULE_LICENSE("GPL");
 
+struct rtl821x_priv {
+	u16 phycr2;
+};
+
 static int rtl821x_read_page(struct phy_device *phydev)
 {
 	return __phy_read(phydev, RTL821x_PAGE_SELECT);
@@ -81,6 +89,28 @@ static int rtl821x_write_page(struct phy_device *phydev, int page)
 	return __phy_write(phydev, RTL821x_PAGE_SELECT, page);
 }
 
+static int rtl821x_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct rtl821x_priv *priv;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->phycr2 = phy_read_paged(phydev, 0xa43, RTL8211F_PHYCR2);
+	if (priv->phycr2 < 0)
+		return priv->phycr2;
+
+	priv->phycr2 &= RTL8211F_CLKOUT_EN;
+	if (of_property_read_bool(dev->of_node, "realtek,clkout-disable"))
+		priv->phycr2 &= ~RTL8211F_CLKOUT_EN;
+
+	phydev->priv = priv;
+
+	return 0;
+}
+
 static int rtl8201_ack_interrupt(struct phy_device *phydev)
 {
 	int err;
@@ -291,6 +321,7 @@ static int rtl8211c_config_init(struct phy_device *phydev)
 
 static int rtl8211f_config_init(struct phy_device *phydev)
 {
+	struct rtl821x_priv *priv = phydev->priv;
 	struct device *dev = &phydev->mdio.dev;
 	u16 val_txdly, val_rxdly;
 	u16 val;
@@ -354,7 +385,15 @@ static int rtl8211f_config_init(struct phy_device *phydev)
 			val_rxdly ? "enabled" : "disabled");
 	}
 
-	return 0;
+	ret = phy_modify_paged(phydev, 0xa43, RTL8211F_PHYCR2,
+			       RTL8211F_CLKOUT_EN, priv->phycr2);
+	if (ret < 0) {
+		dev_err(dev, "clkout configuration failed: %pe\n",
+			ERR_PTR(ret));
+		return ret;
+	}
+
+	return genphy_soft_reset(phydev);
 }
 
 static int rtl8211e_config_init(struct phy_device *phydev)
@@ -847,6 +886,7 @@ static struct phy_driver realtek_drvs[] = {
 	}, {
 		PHY_ID_MATCH_EXACT(0x001cc916),
 		.name		= "RTL8211F Gigabit Ethernet",
+		.probe		= rtl821x_probe,
 		.config_init	= &rtl8211f_config_init,
 		.read_status	= rtlgen_read_status,
 		.config_intr	= &rtl8211f_config_intr,
-- 
2.17.1