Add base DTS file for pmm8155au_2 along with GPIOs, power-on, rtc and vadc
nodes.
Cc: Linus Walleij <linus.walleij@xxxxxxxxxx>
Cc: Liam Girdwood <lgirdwood@xxxxxxxxx>
Cc: Mark Brown <broonie@xxxxxxxxxx>
Cc: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
Cc: Vinod Koul <vkoul@xxxxxxxxxx>
Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Cc: Andy Gross <agross@xxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
Cc: linux-kernel@xxxxxxxxxxxxxxx
Cc: linux-gpio@xxxxxxxxxxxxxxx
Cc: bhupesh.linux@xxxxxxxxx
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi | 107 ++++++++++++++++++++++
1 file changed, 107 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
new file mode 100644
index 000000000000..11c0c203a4e2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+ thermal-zones {
+ pmm8155au-2-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pmm8155au_2_temp>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+
+ trip2 {
+ temperature = <145000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
+&spmi_bus {
+ pmic@4 {
+ compatible = "qcom,pmm8155au-2", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ power-on@800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x0800>;
+
+ status = "disabled";
+ };
+
+ pmm8155au_2_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ io-channels = <&pmm8155au_2_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmm8155au_2_adc: adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ die-temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+ };
+
+ pmm8155au_2_gpios: gpio@c000 {
+ compatible = "qcom,pmm8155au-2-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmic@5 {
+ compatible = "qcom,pmm8155au-2", "qcom,spmi-pmic";
+ reg = <0x5 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
--
2.31.1
