Re: [PATCH v2] dt-bindings: media: video-interfaces: Drop the example

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Rob,

Thank you for the patch.

On Wed, Mar 24, 2021 at 02:22:53PM -0600, Rob Herring wrote:
> The example in video-interfaces.yaml uses a bunch of undocumented
> bindings which will cause warnings when undocumented compatible checks
> are enabled. The example could be fixed to use documented bindings, but
> doing so would just duplicate other examples. So let's just remove the
> example.
> 
> Cc: Mauro Carvalho Chehab <mchehab@xxxxxxxxxx>
> Cc: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
> Cc: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> Cc: linux-media@xxxxxxxxxxxxxxx
> Signed-off-by: Rob Herring <robh@xxxxxxxxxx>

Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>

> ---
> v2: Drop instead of fixing the example
> 
>  .../bindings/media/video-interfaces.yaml      | 127 ------------------
>  1 file changed, 127 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/media/video-interfaces.yaml b/Documentation/devicetree/bindings/media/video-interfaces.yaml
> index 0a7a73fd59f2..4391dce2caee 100644
> --- a/Documentation/devicetree/bindings/media/video-interfaces.yaml
> +++ b/Documentation/devicetree/bindings/media/video-interfaces.yaml
> @@ -215,130 +215,3 @@ properties:
>        CCP2, for instance.
>  
>  additionalProperties: true
> -
> -examples:
> -  # The example snippet below describes two data pipelines.  ov772x and imx074
> -  # are camera sensors with a parallel and serial (MIPI CSI-2) video bus
> -  # respectively. Both sensors are on the I2C control bus corresponding to the
> -  # i2c0 controller node.  ov772x sensor is linked directly to the ceu0 video
> -  # host interface. imx074 is linked to ceu0 through the MIPI CSI-2 receiver
> -  # (csi2). ceu0 has a (single) DMA engine writing captured data to memory.
> -  # ceu0 node has a single 'port' node which may indicate that at any time
> -  # only one of the following data pipelines can be active:
> -  # ov772x -> ceu0 or imx074 -> csi2 -> ceu0.
> -  - |
> -    ceu@fe910000 {
> -        compatible = "renesas,sh-mobile-ceu";
> -        reg = <0xfe910000 0xa0>;
> -        interrupts = <0x880>;
> -
> -        mclk: master_clock {
> -            compatible = "renesas,ceu-clock";
> -            #clock-cells = <1>;
> -            clock-frequency = <50000000>;  /* Max clock frequency */
> -            clock-output-names = "mclk";
> -        };
> -
> -        port {
> -            #address-cells = <1>;
> -            #size-cells = <0>;
> -
> -            /* Parallel bus endpoint */
> -            ceu0_1: endpoint@1 {
> -                reg = <1>;    /* Local endpoint # */
> -                remote-endpoint = <&ov772x_1_1>;  /* Remote phandle */
> -                bus-width = <8>;  /* Used data lines */
> -                data-shift = <2>;  /* Lines 9:2 are used */
> -
> -                /* If hsync-active/vsync-active are missing,
> -                   embedded BT.656 sync is used */
> -                hsync-active = <0>;  /* Active low */
> -                vsync-active = <0>;  /* Active low */
> -                data-active = <1>;  /* Active high */
> -                pclk-sample = <1>;  /* Rising */
> -            };
> -
> -            /* MIPI CSI-2 bus endpoint */
> -            ceu0_0: endpoint@0 {
> -                reg = <0>;
> -                remote-endpoint = <&csi2_2>;
> -            };
> -        };
> -    };
> -
> -    i2c {
> -        #address-cells = <1>;
> -        #size-cells = <0>;
> -
> -        camera@21 {
> -            compatible = "ovti,ov772x";
> -            reg = <0x21>;
> -            vddio-supply = <&regulator1>;
> -            vddcore-supply = <&regulator2>;
> -
> -            clock-frequency = <20000000>;
> -            clocks = <&mclk 0>;
> -            clock-names = "xclk";
> -
> -            port {
> -                /* With 1 endpoint per port no need for addresses. */
> -                ov772x_1_1: endpoint {
> -                    bus-width = <8>;
> -                    remote-endpoint = <&ceu0_1>;
> -                    hsync-active = <1>;
> -                    vsync-active = <0>; /* Who came up with an
> -                               inverter here ?... */
> -                    data-active = <1>;
> -                    pclk-sample = <1>;
> -                };
> -            };
> -        };
> -
> -        camera@1a {
> -            compatible = "sony,imx074";
> -            reg = <0x1a>;
> -            vddio-supply = <&regulator1>;
> -            vddcore-supply = <&regulator2>;
> -
> -            clock-frequency = <30000000>;  /* Shared clock with ov772x_1 */
> -            clocks = <&mclk 0>;
> -            clock-names = "sysclk";    /* Assuming this is the
> -                       name in the datasheet */
> -            port {
> -                imx074_1: endpoint {
> -                    clock-lanes = <0>;
> -                    data-lanes = <1 2>;
> -                    remote-endpoint = <&csi2_1>;
> -                };
> -            };
> -        };
> -    };
> -
> -    csi2: csi2@ffc90000 {
> -        compatible = "renesas,sh-mobile-csi2";
> -        reg = <0xffc90000 0x1000>;
> -        interrupts = <0x17a0>;
> -        #address-cells = <1>;
> -        #size-cells = <0>;
> -
> -        port@1 {
> -            compatible = "renesas,csi2c";  /* One of CSI2I and CSI2C. */
> -            reg = <1>;      /* CSI-2 PHY #1 of 2: PHY_S,
> -                       PHY_M has port address 0,
> -                       is unused. */
> -            csi2_1: endpoint {
> -                clock-lanes = <0>;
> -                data-lanes = <2 1>;
> -                remote-endpoint = <&imx074_1>;
> -            };
> -        };
> -        port@2 {
> -            reg = <2>;      /* port 2: link to the CEU */
> -
> -            csi2_2: endpoint {
> -                remote-endpoint = <&ceu0_0>;
> -            };
> -        };
> -    };
> -
> -...

-- 
Regards,

Laurent Pinchart



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux