[PATCH v5 0/2] Add support for Qualcomm MFD PMIC register layout

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Changes from v4:
- Only one cosmetic change: Moved the declaration of num_virt_regs under
  num_type_reg instead of under num_main_regs in `struct regmap_irq_chip` so as
  to reinforce the idea that it is related to the type setting of IRQs.
- No other changes.

Changes from v3:
- Implemented the scheme proposed in my response to Mark in [4].
- Dropped the RFC tag from this patch series as this series has been tested on
  target with a client driver utilizing these changes.

Changes from v2:
- Split up framework changes patch for better comprehension.
- Dropped PM8008 driver example and converted it into example code in cover
  letter and commit text.
- Added more info in cover letter and commit message as per v2 feedback.

This is a follow-up as promised [1] to the earlier attempts [2] [3] to upstream
the driver that has been hitherto used to handle IRQs for Qualcomm's PMICs that
have multiple on-board peripherals when they are interfaced over the I2C
interface.

This series is a rewrite of that driver while making use of the regmap-irq
framework, which needs some modifications to handle the register layout of
Qualcomm's PMICs. This is an RFC because I would like to get feedback on my
general approach before submitting as a patch per se.

Qualcomm's MFD chips that are interfaced over I2C have a top level interrupt
status register and sub-irqs (peripherals).  When a bit in the main status
register goes high, it means that the peripheral corresponding to that bit has
an unserviced interrupt. If the bit is not set, this means that the
corresponding peripheral does not.

The differences between Qualcomm's register layout and what the regmap-irq
framework assumes are best described with an example:

Suppose that there are three peripherals onboard an MFD chip: MISC, TEMP_ALARM
and GPIO01. Each of these peripherals has the following IRQ configuration
registers: mask, type and ack. There is a top level interrupt status register
and per-peripheral status registers as well (not shown below).

The regmap-irq framework expects all similar registers to be at a fixed stride
from each other, for each peripheral, as below (with stride = 1). 

	/* All mask registers together */
	MISC_INT_MASK		0x1011
	TEMP_ALARM_INT_MASK	0x1012
	GPIO01_INT_MASK		0x1013
	
	/* All type registers together */
	MISC_INT_TYPE		0x2011
	TEMP_ALARM_INT_TYPE	0x2012
	GPIO01_INT_TYPE		0x2013
	
	/* All ack registers together */
	MISC_INT_ACK		0x3011
	TEMP_ALARM_INT_ACK	0x3012
	GPIO01_INT_ACK		0x3013

In contrast, QCOM's registers are laid out as follows:

	/* All of MISC peripheral's registers together */
	MISC_INT_MASK		0x1011
	MISC_INT_TYPE		0x1012
	MISC_INT_ACK		0x1013

	/* All of TEMP_ALARM peripheral's registers together */
	TEMP_ALARM_INT_MASK	0x2011
	TEMP_ALARM_INT_TYPE	0x2012
	TEMP_ALARM_INT_ACK	0x2013
	
	/* All of GPIO01 peripheral's registers together */
	GPIO01_INT_MASK		0x3011
	GPIO01_INT_TYPE		0x3012
	GPIO01_INT_ACK		0x3013

As is evident, the different IRQ configuration registers are just (0x11, 0x12,
0x13) with offsets of (0x1000, 0x2000 and 0x3000) respectively in QCOM's case.
If the *_base registers fed to the struct regmap_irq_chip could be set to the
first peripheral (MISC in this example), then through the sub_reg_offsets
mechanism, we could add the offsets _to_ the *_base register values to get at
the configuration registers for each peripheral.

Hopefully this will help when reviewing the changes in this series.

[1] https://lore.kernel.org/lkml/20200519185757.GA13992@xxxxxxxxxxxxxx/
[2] https://lore.kernel.org/lkml/cover.1588037638.git.gurus@xxxxxxxxxxxxxx/
[3] https://lore.kernel.org/lkml/cover.1588115326.git.gurus@xxxxxxxxxxxxxx/
[4] https://lore.kernel.org/lkml/20210315203336.GA8977@xxxxxxxxxxxxxx/

Guru Das Srinagesh (2):
  regmap-irq: Introduce virtual regs to handle more config regs
  regmap-irq: Add driver callback to configure virtual regs

 drivers/base/regmap/regmap-irq.c | 43 +++++++++++++++++++++++++++++++++++++++-
 include/linux/regmap.h           |  9 +++++++++
 2 files changed, 51 insertions(+), 1 deletion(-)

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux