Re: [PATCH v10 3/8] drivers: thermal: tsens: Convert msm8960 to reg_field

[Thara Gopinath <thara.gopinath@xxxxxxxxxx>]

On 2/17/21 2:40 PM, Ansuel Smith wrote:
> Convert msm9860 driver to reg_field to use the init_common
> function.

Hi!

Now that you have done this, you should clean up the unused 
bitmasks/offsets etc in
tsens-8960.c file as well as a separate patch. I only see the
need to maintain SLP_CLK_ENA_8660 and SLP_CLK_ENA. Everything else can 
be removed and the s/w can use priv->rf[_field_] for access.
Otherwise for this patch

Acked-by: Thara Gopinath <thara.gopinath@xxxxxxxxxx>

Warm Regards
Thara
> Signed-off-by: Ansuel Smith <ansuelsmth@xxxxxxxxx>
> ---
>   drivers/thermal/qcom/tsens-8960.c | 80 ++++++++++++++++++++++++++++++-
>   1 file changed, 79 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/thermal/qcom/tsens-8960.c b/drivers/thermal/qcom/tsens-8960.c
> index 2a28a5af209e..3f4fc1ffe679 100644
> --- a/drivers/thermal/qcom/tsens-8960.c
> +++ b/drivers/thermal/qcom/tsens-8960.c
> @@ -51,11 +51,22 @@
>   #define MIN_LIMIT_TH		0x0
>   #define MAX_LIMIT_TH		0xff
>   
> -#define S0_STATUS_ADDR		0x3628
>   #define INT_STATUS_ADDR		0x363c
>   #define TRDY_MASK		BIT(7)
>   #define TIMEOUT_US		100
>   
> +#define S0_STATUS_OFF		0x3628
> +#define S1_STATUS_OFF		0x362c
> +#define S2_STATUS_OFF		0x3630
> +#define S3_STATUS_OFF		0x3634
> +#define S4_STATUS_OFF		0x3638
> +#define S5_STATUS_OFF		0x3664  /* Sensors 5-10 found on apq8064/msm8960 */
> +#define S6_STATUS_OFF		0x3668
> +#define S7_STATUS_OFF		0x366c
> +#define S8_STATUS_OFF		0x3670
> +#define S9_STATUS_OFF		0x3674
> +#define S10_STATUS_OFF		0x3678
> +
>   static int suspend_8960(struct tsens_priv *priv)
>   {
>   	int ret;
> @@ -269,6 +280,71 @@ static int get_temp_8960(const struct tsens_sensor *s, int *temp)
>   	return -ETIMEDOUT;
>   }
>   
> +static struct tsens_features tsens_8960_feat = {
> +	.ver_major	= VER_0,
> +	.crit_int	= 0,
> +	.adc		= 1,
> +	.srot_split	= 0,
> +	.max_sensors	= 11,
> +};
> +
> +static const struct reg_field tsens_8960_regfields[MAX_REGFIELDS] = {
> +	/* ----- SROT ------ */
> +	/* No VERSION information */
> +
> +	/* CNTL */
> +	[TSENS_EN]     = REG_FIELD(CNTL_ADDR,  0, 0),
> +	[TSENS_SW_RST] = REG_FIELD(CNTL_ADDR,  1, 1),
> +	/* 8960 has 5 sensors, 8660 has 11, we only handle 5 */
> +	[SENSOR_EN]    = REG_FIELD(CNTL_ADDR,  3, 7),
> +
> +	/* ----- TM ------ */
> +	/* INTERRUPT ENABLE */
> +	/* NO INTERRUPT ENABLE */
> +
> +	/* Single UPPER/LOWER TEMPERATURE THRESHOLD for all sensors */
> +	[LOW_THRESH_0]   = REG_FIELD(THRESHOLD_ADDR,  0,  7),
> +	[UP_THRESH_0]    = REG_FIELD(THRESHOLD_ADDR,  8, 15),
> +	/* MIN_THRESH_0 and MAX_THRESH_0 are not present in the regfield
> +	 * Recycle CRIT_THRESH_0 and 1 to set the required regs to hardcoded temp
> +	 * MIN_THRESH_0 -> CRIT_THRESH_1
> +	 * MAX_THRESH_0 -> CRIT_THRESH_0
> +	 */
> +	[CRIT_THRESH_1]   = REG_FIELD(THRESHOLD_ADDR, 16, 23),
> +	[CRIT_THRESH_0]   = REG_FIELD(THRESHOLD_ADDR, 24, 31),
> +
> +	/* UPPER/LOWER INTERRUPT [CLEAR/STATUS] */
> +	/* 1 == clear, 0 == normal operation */
> +	[LOW_INT_CLEAR_0]   = REG_FIELD(CNTL_ADDR,  9,  9),
> +	[UP_INT_CLEAR_0]    = REG_FIELD(CNTL_ADDR, 10, 10),
> +
> +	/* NO CRITICAL INTERRUPT SUPPORT on 8960 */
> +
> +	/* Sn_STATUS */
> +	[LAST_TEMP_0]  = REG_FIELD(S0_STATUS_OFF,  0,  7),
> +	[LAST_TEMP_1]  = REG_FIELD(S1_STATUS_OFF,  0,  7),
> +	[LAST_TEMP_2]  = REG_FIELD(S2_STATUS_OFF,  0,  7),
> +	[LAST_TEMP_3]  = REG_FIELD(S3_STATUS_OFF,  0,  7),
> +	[LAST_TEMP_4]  = REG_FIELD(S4_STATUS_OFF,  0,  7),
> +	[LAST_TEMP_5]  = REG_FIELD(S5_STATUS_OFF,  0,  7),
> +	[LAST_TEMP_6]  = REG_FIELD(S6_STATUS_OFF,  0,  7),
> +	[LAST_TEMP_7]  = REG_FIELD(S7_STATUS_OFF,  0,  7),
> +	[LAST_TEMP_8]  = REG_FIELD(S8_STATUS_OFF,  0,  7),
> +	[LAST_TEMP_9]  = REG_FIELD(S9_STATUS_OFF,  0,  7),
> +	[LAST_TEMP_10] = REG_FIELD(S10_STATUS_OFF, 0,  7),
> +
> +	/* No VALID field on 8960 */
> +	/* TSENS_INT_STATUS bits: 1 == threshold violated */
> +	[MIN_STATUS_0] = REG_FIELD(INT_STATUS_ADDR, 0, 0),
> +	[LOWER_STATUS_0] = REG_FIELD(INT_STATUS_ADDR, 1, 1),
> +	[UPPER_STATUS_0] = REG_FIELD(INT_STATUS_ADDR, 2, 2),
> +	/* No CRITICAL field on 8960 */
> +	[MAX_STATUS_0] = REG_FIELD(INT_STATUS_ADDR, 3, 3),
> +
> +	/* TRDY: 1=ready, 0=in progress */
> +	[TRDY] = REG_FIELD(INT_STATUS_ADDR, 7, 7),
> +};
> +
>   static const struct tsens_ops ops_8960 = {
>   	.init		= init_8960,
>   	.calibrate	= calibrate_8960,
> @@ -282,4 +358,6 @@ static const struct tsens_ops ops_8960 = {
>   struct tsens_plat_data data_8960 = {
>   	.num_sensors	= 11,
>   	.ops		= &ops_8960,
> +	.feat		= &tsens_8960_feat,
> +	.fields		= tsens_8960_regfields,
>   };