From: Sumit Semwal <sumit.semwal@xxxxxxxxxx>
Enabling the Display panel for beryllium phone (Xiaomi
Pocophone F1) requires DSI labibb regulators and panel
dts nodes to be added. It is also required to keep some
of the regulators as always-on.
Signed-off-by: Sumit Semwal <sumit.semwal@xxxxxxxxxx>
Signed-off-by: Amit Pundir <amit.pundir@xxxxxxxxxx>
---
.../boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 55 ++++++++++++++++++++++
1 file changed, 55 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
index cd15ae0347e8..e09effa555f1 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
@@ -160,6 +160,14 @@
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
+ vreg_l14a_1p88: ldo14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vreg_l17a_1p3: ldo17 {
regulator-min-microvolt = <1304000>;
regulator-max-microvolt = <1304000>;
@@ -194,6 +202,7 @@
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-boot-on;
};
};
};
@@ -207,6 +216,44 @@
firmware-name = "qcom/sdm845/cdsp.mdt";
};
+&dsi0 {
+ status = "okay";
+ vdda-supply = <&vreg_l26a_1p2>;
+
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&tianma_nt36672a_in_0>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+
+ panel@0 {
+ compatible = "tianma,fhd-video";
+ reg = <0>;
+ vddi0-supply = <&vreg_l14a_1p88>;
+ vddpos-supply = <&lab>;
+ vddneg-supply = <&ibb>;
+
+ reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port {
+ tianma_nt36672a_in_0: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+};
+
+&dsi0_phy {
+ status = "okay";
+ vdds-supply = <&vreg_l1a_0p875>;
+};
+
&gcc {
protected-clocks = <GCC_QSPI_CORE_CLK>,
<GCC_QSPI_CORE_CLK_SRC>,
@@ -274,6 +321,14 @@
};
+&mdss {
+ status = "okay";
+};
+
+&mdss_mdp {
+ status = "okay";
+};
+
&mss_pil {
status = "okay";
firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mdt";
--
2.7.4
