[PATCH v2 14/22] dt-bindings: media: camss: Add qcom,msm8996-camss binding

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add bindings for qcom,msm8996-camss in order to support the camera
subsystem on MSM8996.

Signed-off-by: Robert Foss <robert.foss@xxxxxxxxxx>
---

Changes since v1:
 - Laurent: Reworked driver to use dtschema


 .../bindings/media/qcom,msm8996-camss.yaml    | 418 ++++++++++++++++++
 1 file changed, 418 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/qcom,msm8996-camss.yaml

diff --git a/Documentation/devicetree/bindings/media/qcom,msm8996-camss.yaml b/Documentation/devicetree/bindings/media/qcom,msm8996-camss.yaml
new file mode 100644
index 000000000000..5ca0be8892ab
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/qcom,msm8996-camss.yaml
@@ -0,0 +1,418 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/media/qcom,msm8996-camss.yaml#";
+$schema: "http://devicetree.org/meta-schemas/core.yaml#";
+
+title: Qualcomm CAMSS ISP
+
+maintainers:
+  - Robert Foss <robert.foss@xxxxxxxxxx>
+  - Todor Tomov <todor.too@xxxxxxxxx>
+
+description: |
+  The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms
+
+properties:
+  compatible:
+    const: qcom,msm8996-camss
+
+  clocks:
+    description:
+      Input clocks for the hardware block.
+    minItems: 36
+    maxItems: 36
+
+  clock-names:
+    description:
+      Names of input clocks for the hardware block.
+    items:
+      - const: top_ahb
+      - const: ispif_ahb
+      - const: csiphy0_timer
+      - const: csiphy1_timer
+      - const: csiphy2_timer
+      - const: csi0_ahb
+      - const: csi0
+      - const: csi0_phy
+      - const: csi0_pix
+      - const: csi0_rdi
+      - const: csi1_ahb
+      - const: csi1
+      - const: csi1_phy
+      - const: csi1_pix
+      - const: csi1_rdi
+      - const: csi2_ahb
+      - const: csi2
+      - const: csi2_phy
+      - const: csi2_pix
+      - const: csi2_rdi
+      - const: csi3_ahb
+      - const: csi3
+      - const: csi3_phy
+      - const: csi3_pix
+      - const: csi3_rdi
+      - const: ahb
+      - const: vfe0
+      - const: csi_vfe0
+      - const: vfe0_ahb
+      - const: vfe0_stream
+      - const: vfe1
+      - const: csi_vfe1
+      - const: vfe1_ahb
+      - const: vfe1_stream
+      - const: vfe_ahb
+      - const: vfe_axi
+
+  interrupts:
+    description:
+      IRQs for the hardware block.
+    minItems: 10
+    maxItems: 10
+
+  interrupt-names:
+    description:
+      Names of IRQs for the hardware block.
+    items:
+      - const: csiphy0
+      - const: csiphy1
+      - const: csiphy2
+      - const: csid0
+      - const: csid1
+      - const: csid2
+      - const: csid3
+      - const: ispif
+      - const: vfe0
+      - const: vfe1
+
+  iommus:
+    maxItems: 4
+
+  power-domains:
+    maxItems: 2
+
+  ports:
+    description:
+      The CSI data input ports.
+
+    type: object
+
+    properties:
+      port@0:
+        type: object
+        description: Input node for receiving CSI data.
+        properties:
+          endpoint:
+            type: object
+
+            properties:
+              clock-lanes:
+                description: |-
+                  The physical clock lane index. The value must
+                  always be <7> as the hardware supports D-PHY
+                  and C-PHY, indexes are in a common set and
+                  D-PHY physical clock lane is labeled as 7.
+
+              data-lanes:
+                description: |-
+                  An array of physical data lanes indexes.
+                  Position of an entry determines the logical
+                  lane number, while the value of an entry
+                  indicates physical lane index. Lane swapping
+                  is supported. Physical lane indexes are:
+                  0, 1, 2, 3
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+        required:
+          - endpoint
+          - reg
+
+      port@1:
+        type: object
+        description: Input node for receiving CSI data.
+        properties:
+          endpoint:
+            type: object
+
+            properties:
+              clock-lanes:
+                description: |-
+                  The physical clock lane index. The value must
+                  always be <7> as the hardware supports D-PHY
+                  and C-PHY, indexes are in a common set and
+                  D-PHY physical clock lane is labeled as 7.
+
+              data-lanes:
+                description: |-
+                  An array of physical data lanes indexes.
+                  Position of an entry determines the logical
+                  lane number, while the value of an entry
+                  indicates physical lane index. Lane swapping
+                  is supported. Physical lane indexes are:
+                  0, 1, 2, 3
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+        required:
+          - endpoint
+          - reg
+
+      port@2:
+        type: object
+        description: Input node for receiving CSI data.
+        properties:
+          endpoint:
+            type: object
+
+            properties:
+              clock-lanes:
+                description: |-
+                  The physical clock lane index. The value must
+                  always be <7> as the hardware supports D-PHY
+                  and C-PHY, indexes are in a common set and
+                  D-PHY physical clock lane is labeled as 7.
+
+              data-lanes:
+                description: |-
+                  An array of physical data lanes indexes.
+                  Position of an entry determines the logical
+                  lane number, while the value of an entry
+                  indicates physical lane index. Lane swapping
+                  is supported. Physical lane indexes are:
+                  0, 1, 2, 3
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+        required:
+          - endpoint
+          - reg
+
+      port@3:
+        type: object
+        description: Input node for receiving CSI data.
+        properties:
+          endpoint:
+            type: object
+
+            properties:
+              clock-lanes:
+                description: |-
+                  The physical clock lane index. The value must
+                  always be <7> as the hardware supports D-PHY
+                  and C-PHY, indexes are in a common set and
+                  D-PHY physical clock lane is labeled as 7.
+
+              data-lanes:
+                description: |-
+                  An array of physical data lanes indexes.
+                  Position of an entry determines the logical
+                  lane number, while the value of an entry
+                  indicates physical lane index. Lane swapping
+                  is supported. Physical lane indexes are:
+                  0, 1, 2, 3
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+        required:
+          - endpoint
+          - reg
+
+  reg:
+    minItems: 14
+    maxItems: 14
+
+  reg-names:
+    items:
+      - const: csiphy0
+      - const: csiphy0_clk_mux
+      - const: csiphy1
+      - const: csiphy1_clk_mux
+      - const: csiphy2
+      - const: csiphy2_clk_mux
+      - const: csid0
+      - const: csid1
+      - const: csid2
+      - const: csid3
+      - const: ispif
+      - const: csi_clk_mux
+      - const: vfe0
+      - const: vfe1
+
+  vdda-supply:
+    description:
+      Definition of the regulator used as analog power supply.
+
+required:
+  - clock-names
+  - clocks
+  - compatible
+  - interrupt-names
+  - interrupts
+  - iommus
+  - power-domains
+  - reg
+  - reg-names
+  - vdda-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/qcom,gcc-msm8996.h>
+    #include <dt-bindings/clock/qcom,mmcc-msm8996.h>
+
+    camss: camss@a00000 {
+      compatible = "qcom,msm8996-camss";
+
+      clocks = <&mmcc CAMSS_TOP_AHB_CLK>,
+        <&mmcc CAMSS_ISPIF_AHB_CLK>,
+        <&mmcc CAMSS_CSI0PHYTIMER_CLK>,
+        <&mmcc CAMSS_CSI1PHYTIMER_CLK>,
+        <&mmcc CAMSS_CSI2PHYTIMER_CLK>,
+        <&mmcc CAMSS_CSI0_AHB_CLK>,
+        <&mmcc CAMSS_CSI0_CLK>,
+        <&mmcc CAMSS_CSI0PHY_CLK>,
+        <&mmcc CAMSS_CSI0PIX_CLK>,
+        <&mmcc CAMSS_CSI0RDI_CLK>,
+        <&mmcc CAMSS_CSI1_AHB_CLK>,
+        <&mmcc CAMSS_CSI1_CLK>,
+        <&mmcc CAMSS_CSI1PHY_CLK>,
+        <&mmcc CAMSS_CSI1PIX_CLK>,
+        <&mmcc CAMSS_CSI1RDI_CLK>,
+        <&mmcc CAMSS_CSI2_AHB_CLK>,
+        <&mmcc CAMSS_CSI2_CLK>,
+        <&mmcc CAMSS_CSI2PHY_CLK>,
+        <&mmcc CAMSS_CSI2PIX_CLK>,
+        <&mmcc CAMSS_CSI2RDI_CLK>,
+        <&mmcc CAMSS_CSI3_AHB_CLK>,
+        <&mmcc CAMSS_CSI3_CLK>,
+        <&mmcc CAMSS_CSI3PHY_CLK>,
+        <&mmcc CAMSS_CSI3PIX_CLK>,
+        <&mmcc CAMSS_CSI3RDI_CLK>,
+        <&mmcc CAMSS_AHB_CLK>,
+        <&mmcc CAMSS_VFE0_CLK>,
+        <&mmcc CAMSS_CSI_VFE0_CLK>,
+        <&mmcc CAMSS_VFE0_AHB_CLK>,
+        <&mmcc CAMSS_VFE0_STREAM_CLK>,
+        <&mmcc CAMSS_VFE1_CLK>,
+        <&mmcc CAMSS_CSI_VFE1_CLK>,
+        <&mmcc CAMSS_VFE1_AHB_CLK>,
+        <&mmcc CAMSS_VFE1_STREAM_CLK>,
+        <&mmcc CAMSS_VFE_AHB_CLK>,
+        <&mmcc CAMSS_VFE_AXI_CLK>;
+
+      clock-names = "top_ahb",
+        "ispif_ahb",
+        "csiphy0_timer",
+        "csiphy1_timer",
+        "csiphy2_timer",
+        "csi0_ahb",
+        "csi0",
+        "csi0_phy",
+        "csi0_pix",
+        "csi0_rdi",
+        "csi1_ahb",
+        "csi1",
+        "csi1_phy",
+        "csi1_pix",
+        "csi1_rdi",
+        "csi2_ahb",
+        "csi2",
+        "csi2_phy",
+        "csi2_pix",
+        "csi2_rdi",
+        "csi3_ahb",
+        "csi3",
+        "csi3_phy",
+        "csi3_pix",
+        "csi3_rdi",
+        "ahb",
+        "vfe0",
+        "csi_vfe0",
+        "vfe0_ahb",
+        "vfe0_stream",
+        "vfe1",
+        "csi_vfe1",
+        "vfe1_ahb",
+        "vfe1_stream",
+        "vfe_ahb",
+        "vfe_axi";
+
+      interrupts = <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>,
+        <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>,
+        <GIC_SPI 80 IRQ_TYPE_EDGE_RISING>,
+        <GIC_SPI 296 IRQ_TYPE_EDGE_RISING>,
+        <GIC_SPI 297 IRQ_TYPE_EDGE_RISING>,
+        <GIC_SPI 298 IRQ_TYPE_EDGE_RISING>,
+        <GIC_SPI 299 IRQ_TYPE_EDGE_RISING>,
+        <GIC_SPI 309 IRQ_TYPE_EDGE_RISING>,
+        <GIC_SPI 314 IRQ_TYPE_EDGE_RISING>,
+        <GIC_SPI 315 IRQ_TYPE_EDGE_RISING>;
+
+      interrupt-names = "csiphy0",
+        "csiphy1",
+        "csiphy2",
+        "csid0",
+        "csid1",
+        "csid2",
+        "csid3",
+        "ispif",
+        "vfe0",
+        "vfe1";
+
+      iommus = <&vfe_smmu 0>,
+         <&vfe_smmu 1>,
+         <&vfe_smmu 2>,
+         <&vfe_smmu 3>;
+
+      power-domains = <&mmcc VFE0_GDSC>,
+        <&mmcc VFE1_GDSC>;
+
+      reg = <0x00a34000 0x1000>,
+        <0x00a00030 0x4>,
+        <0x00a35000 0x1000>,
+        <0x00a00038 0x4>,
+        <0x00a36000 0x1000>,
+        <0x00a00040 0x4>,
+        <0x00a30000 0x100>,
+        <0x00a30400 0x100>,
+        <0x00a30800 0x100>,
+        <0x00a30c00 0x100>,
+        <0x00a31000 0x500>,
+        <0x00a00020 0x10>,
+        <0x00a10000 0x1000>,
+        <0x00a14000 0x1000>;
+
+      reg-names = "csiphy0",
+        "csiphy0_clk_mux",
+        "csiphy1",
+        "csiphy1_clk_mux",
+        "csiphy2",
+        "csiphy2_clk_mux",
+        "csid0",
+        "csid1",
+        "csid2",
+        "csid3",
+        "ispif",
+        "csi_clk_mux",
+        "vfe0",
+        "vfe1";
+
+      vdda-supply = <&reg_2v8>;
+
+      ports {
+        #address-cells = <1>;
+        #size-cells = <0>;
+      };
+    };
\ No newline at end of file
-- 
2.27.0




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux