From: Zoltan HERPAI <wigyori@xxxxxxx> The LinkSprite pcDuino V3 is an A20 based development board featuring arduino compatible io headers, 1G RAM, 4G nand, sata, rtl8188cus usb wifi and 100 Mbit ethernet using an ip101a phy: http://www.pcduino.com/pcduino-v3/ Signed-off-by: Zoltan HERPAI <wigyori@xxxxxxx> [hdegoede@xxxxxxxxxx: Various cleanups, correct led pins] [hdegoede@xxxxxxxxxx: Add axp209, ir and gpio-keys nodes] Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx> -- Changes since v2: - update MMC entry to comply with upstream - unify the 4 patches into one Changes since v1: - fix cosmetic issues - fix i2c entry - remove unnecessary input bindings include - add MMC support --- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/sun7i-a20-pcduino3.dts | 173 +++++++++++++++++++++++++++++++ 2 files changed, 175 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/sun7i-a20-pcduino3.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index ed0de8b..fdc590e 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -380,7 +380,8 @@ dtb-$(CONFIG_MACH_SUN7I) += \ sun7i-a20-cubieboard2.dtb \ sun7i-a20-cubietruck.dtb \ sun7i-a20-i12-tvbox.dtb \ - sun7i-a20-olinuxino-micro.dtb + sun7i-a20-olinuxino-micro.dtb \ + sun7i-a20-pcduino3.dtb dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \ tegra20-iris-512.dtb \ tegra20-medcom-wide.dtb \ diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts b/arch/arm/boot/dts/sun7i-a20-pcduino3.dts new file mode 100644 index 0000000..168b0bc --- /dev/null +++ b/arch/arm/boot/dts/sun7i-a20-pcduino3.dts @@ -0,0 +1,173 @@ +/* + * Copyright 2014 Zoltan HERPAI + * Zoltan HERPAI <wigyori@xxxxxxx> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "sun7i-a20.dtsi" +/include/ "sunxi-common-regulators.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "LinkSprite pcDuino3"; + compatible = "linksprite,pcduino3", "allwinner,sun7i-a20"; + + soc@01c00000 { + mmc0: mmc@01c0f000 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 1 0>; /* PH1 */ + cd-inverted; + status = "okay"; + }; + + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + ahci: sata@01c18000 { + target-supply = <®_ahci_5v>; + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; + }; + + pinctrl@01c20800 { + ahci_pwr_pin_a: ahci_pwr_pin@0 { + allwinner,pins = "PH2"; + }; + + led_pins_pcduino3: led_pins@0 { + allwinner,pins = "PH15", "PH16"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + key_pins_pcduino3: key_pins@0 { + allwinner,pins = "PH17", "PH18", "PH19"; + allwinner,function = "gpio_in"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + }; + + ir0: ir@01c21800 { + pinctrl-names = "default"; + pinctrl-0 = <&ir0_pins_a>; + status = "okay"; + }; + + uart0: serial@01c28000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; + }; + + i2c0: i2c@01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 8>; + + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + gmac: ethernet@01c50000 { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_mii_a>; + phy = <&phy1>; + phy-mode = "mii"; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_pcduino3>; + + tx { + label = "pcduino3:green:tx"; + gpios = <&pio 7 15 GPIO_ACTIVE_LOW>; + }; + + rx { + label = "pcduino3:green:rx"; + gpios = <&pio 7 16 GPIO_ACTIVE_LOW>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&key_pins_pcduino3>; + #address-cells = <1>; + #size-cells = <0>; + button@0 { + label = "Key Back"; + linux,code = <KEY_BACK>; + gpios = <&pio 7 17 GPIO_ACTIVE_LOW>; + }; + button@1 { + label = "Key Home"; + linux,code = <KEY_HOME>; + gpios = <&pio 7 18 GPIO_ACTIVE_LOW>; + }; + button@2 { + label = "Key Menu"; + linux,code = <KEY_MENU>; + gpios = <&pio 7 19 GPIO_ACTIVE_LOW>; + }; + }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; + + reg_ahci_5v: ahci-5v { + gpio = <&pio 7 2 0>; + status = "okay"; + }; +}; -- 2.0.0 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
