Hi,
On Wed, Dec 16, 2020 at 08:09:36AM +0100, Pavel Löbl wrote:
> Banana Pi P2 Zero is H2+-based board by Sinovoip internally
> similar to Banana Pi M2 Zero.
>
> It features:
> - Allwinner H2+, Quad-core Cortex-A7
> - 512MB DDR3 SDRAM
> - 8G eMMC flash
> - MicroSD card slot
> - 100M LAN
> - WiFi (AP6212) & Bluetooth onboard (SDIO + UART)
> - Micro USB OTG port
> - Micro USB connector (power only)
> - Mini HDMI
> - 40 PIN GPIO includes UART, SPI, I2C, IO etc.
> - GPIO-connected key and LED
> - CSI connector
> - IEEE 802.3af PoE standard PoE module support (optional)
>
> This adds support for v1.1 revision. There was also v1.0 available
> which has different SDcard CD polarity and Ethernet port LEDs
> disconnected in layout.
You should name that file sun8i-h2-plus-bananapi-p2-zero-v1.1 (and the
compatible) to avoid any confusion
> Signed-off-by: Pavel Löbl <pavel@xxxxxxxx>
> ---
> .../dts/sun8i-h2-plus-bananapi-p2-zero.dts | 195 ++++++++++++++++++
> 1 file changed, 195 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-bananapi-p2-zero.dts
>
> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-p2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-p2-zero.dts
> new file mode 100644
> index 000000000000..431108bff68e
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-p2-zero.dts
> @@ -0,0 +1,195 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2020 Pavel Löbl <pavel@xxxxxxxx>
> + *
> + * Based on sun8i-h2-plus-bananapi-m2-zero.dts, which is:
> + * Copyright (C) 2017 Icenowy Zheng <icenowy@xxxxxxx>
> + */
> +
> +/dts-v1/;
> +#include "sun8i-h3.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + model = "Banana Pi BPI-P2-Zero";
> + compatible = "sinovoip,bpi-p2-zero", "allwinner,sun8i-h2-plus";
This compatible should be documented in
Documentation/devicetree/bindings/arm/sunxi.yaml
> + aliases {
> + serial0 = &uart0;
> + serial1 = &uart1;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + pwr_led {
The name of that node should be led
> + label = "power-led";
Labels are deprecated, you should be using function and color instead.
> + gpios = <&r_pio 0 10 GPIO_ACTIVE_LOW>; /* PL10 */
> + default-state = "on";
> + };
> + };
> +
> + gpio_keys {
underscores are not valid in node names
> + compatible = "gpio-keys";
> +
> + pwr_key {
Same thing here
> + label = "power-key";
> + linux,code = <KEY_POWER>;
> + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
> + wakeup-source;
> + };
> + };
> +
> + reg_vcc_5v: reg-vcc-5v {
> + compatible = "regulator-fixed";
> + regulator-name = "usb1-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + };
> +
> + reg_vcc_1v2: reg-vcc-1v2 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-1v2";
> + regulator-type = "voltage";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-boot-on;
> + vin-supply = <®_vcc_5v>;
> + };
> +
> + reg_vcc_3v3: reg-vcc-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-3v3";
> + regulator-type = "voltage";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + vin-supply = <®_vcc_5v>;
> + };
> +
> + reg_vdd_cpux: vdd-cpux-regulator {
> + compatible = "regulator-gpio";
> + regulator-name = "vdd-cpux";
> + regulator-type = "voltage";
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-ramp-delay = <50>; /* 4ms */
> +
> + gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
> + enable-active-high;
> + gpios-states = <0x1>;
> + states = <1100000 0>, <1300000 1>;
> + };
> +
> + wifi_pwrseq: wifi_pwrseq {
Same thing here
Looks good otherwise, thanks!
Maxime
Attachment:
signature.asc
Description: PGP signature
