Hi Mathieu,
On Wed, 2 Dec 2020 at 23:57, Mathieu Poirier <mathieu.poirier@xxxxxxxxxx> wrote:
>
> On Thu, Nov 19, 2020 at 03:08:47PM +0100, Grzegorz Jaszczyk wrote:
> > The firmware blob can contain optional ELF sections: .resource_table
> > section and .pru_irq_map one. The second one contains the PRUSS
> > interrupt mapping description, which needs to be setup before powering
> > on the PRU core. To avoid RAM wastage this ELF section is not mapped to
> > any ELF segment (by the firmware linker) and therefore is not loaded to
> > PRU memory.
> >
> > The PRU interrupt configuration is handled within the PRUSS INTC irqchip
> > driver and leverages the system events to interrupt channels and host
> > interrupts mapping configuration. Relevant irq routing information is
> > passed through a special .pru_irq_map ELF section (for interrupts routed
> > to and used by PRU cores) or via the PRU application's device tree node
> > (for interrupts routed to and used by the main CPU). The mappings are
> > currently programmed during the booting/shutdown of the PRU.
> >
> > The interrupt configuration passed through .pru_irq_map ELF section is
> > optional. It varies on specific firmware functionality and therefore
> > have to be unwinded during PRU stop and performed again during
> > PRU start.
> >
> > Co-developed-by: Suman Anna <s-anna@xxxxxx>
> > Signed-off-by: Suman Anna <s-anna@xxxxxx>
> > Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@xxxxxxxxxx>
> > ---
> > v1->v2:
> > Address Suman comments:
> > - Rework pru_rproc_find_interrupt_map() style: get rid of generic ELF
> > helpers macros usage and stick with elf32_* related structs instead
> > (in order to be consistent with pru_rproc_load_elf_segments() style).
> > - Improve comments and dev_err msgs in pru_rproc_find_interrupt_map().
> > - Use u8 instead of ssize_t for evt_count.
> > ---
> > drivers/remoteproc/pru_rproc.c | 180 +++++++++++++++++++++++++++++++++
> > drivers/remoteproc/pru_rproc.h | 46 +++++++++
> > 2 files changed, 226 insertions(+)
> > create mode 100644 drivers/remoteproc/pru_rproc.h
> >
> > diff --git a/drivers/remoteproc/pru_rproc.c b/drivers/remoteproc/pru_rproc.c
> > index b686f19f9b1a..c68c3d6bfddd 100644
> > --- a/drivers/remoteproc/pru_rproc.c
> > +++ b/drivers/remoteproc/pru_rproc.c
> > @@ -11,13 +11,16 @@
> > */
> >
> > #include <linux/bitops.h>
> > +#include <linux/irqdomain.h>
> > #include <linux/module.h>
> > #include <linux/of_device.h>
> > +#include <linux/of_irq.h>
> > #include <linux/pruss_driver.h>
> > #include <linux/remoteproc.h>
> >
> > #include "remoteproc_internal.h"
> > #include "remoteproc_elf_helpers.h"
> > +#include "pru_rproc.h"
> >
> > /* PRU_ICSS_PRU_CTRL registers */
> > #define PRU_CTRL_CTRL 0x0000
> > @@ -42,6 +45,8 @@
> > #define PRU_SDRAM_DA 0x2000 /* Secondary Data RAM */
> > #define PRU_SHRDRAM_DA 0x10000 /* Shared Data RAM */
> >
> > +#define MAX_PRU_SYS_EVENTS 160
> > +
> > /**
> > * enum pru_iomem - PRU core memory/register range identifiers
> > *
> > @@ -65,6 +70,10 @@ enum pru_iomem {
> > * @rproc: remoteproc pointer for this PRU core
> > * @mem_regions: data for each of the PRU memory regions
> > * @fw_name: name of firmware image used during loading
> > + * @mapped_irq: virtual interrupt numbers of created fw specific mapping
> > + * @pru_interrupt_map: pointer to interrupt mapping description (firmware)
> > + * @pru_interrupt_map_sz: pru_interrupt_map size
> > + * @evt_count: number of mapped events
> > */
> > struct pru_rproc {
> > int id;
> > @@ -73,6 +82,10 @@ struct pru_rproc {
> > struct rproc *rproc;
> > struct pruss_mem_region mem_regions[PRU_IOMEM_MAX];
> > const char *fw_name;
> > + int *mapped_irq;
> > + struct pru_irq_rsc *pru_interrupt_map;
> > + size_t pru_interrupt_map_sz;
> > + u8 evt_count;
> > };
> >
> > static inline u32 pru_control_read_reg(struct pru_rproc *pru, unsigned int reg)
> > @@ -86,15 +99,107 @@ void pru_control_write_reg(struct pru_rproc *pru, unsigned int reg, u32 val)
> > writel_relaxed(val, pru->mem_regions[PRU_IOMEM_CTRL].va + reg);
> > }
> >
>
> > +static void pru_dispose_irq_mapping(struct pru_rproc *pru)
> > +{
> > + while (pru->evt_count--) {
> > + if (pru->mapped_irq[pru->evt_count] > 0)
> > + irq_dispose_mapping(pru->mapped_irq[pru->evt_count]);
> > + }
> > +
> > + kfree(pru->mapped_irq);
> > +}
> > +
> > +/*
> > + * Parse the custom PRU interrupt map resource and configure the INTC
> > + * appropriately.
> > + */
> > +static int pru_handle_intrmap(struct rproc *rproc)
> > +{
> > + struct device *dev = rproc->dev.parent;
> > + struct pru_rproc *pru = rproc->priv;
> > + struct pru_irq_rsc *rsc = pru->pru_interrupt_map;
> > + struct irq_fwspec fwspec;
> > + struct device_node *irq_parent;
> > + int i, ret = 0;
> > +
> > + /* not having pru_interrupt_map is not an error */
> > + if (!rsc)
> > + return 0;
> > +
> > + /* currently supporting only type 0 */
> > + if (rsc->type != 0) {
> > + dev_err(dev, "unsupported rsc type: %d\n", rsc->type);
> > + return -EINVAL;
> > + }
> > +
> > + if (rsc->num_evts < 0 || rsc->num_evts > MAX_PRU_SYS_EVENTS)
> > + return -EINVAL;
> > +
>
> pru_irq_rsc::num_evts is a 'u8' and can't be negative.
Sure - I will remove the 'rsc->num_evts < 0 ' check.
>
> > + if (sizeof(*rsc) + rsc->num_evts * sizeof(struct pruss_int_map) !=
> > + pru->pru_interrupt_map_sz)
> > + return -EINVAL;
> > +
> > + pru->evt_count = rsc->num_evts;
> > + pru->mapped_irq = kcalloc(pru->evt_count, sizeof(int), GFP_KERNEL);
> > + if (!pru->mapped_irq)
> > + return -ENOMEM;
> > +
> > + /*
> > + * parse and fill in system event to interrupt channel and
> > + * channel-to-host mapping
> > + */
> > + irq_parent = of_irq_find_parent(pru->dev->of_node);
> > + if (!irq_parent) {
> > + kfree(pru->mapped_irq);
> > + return -ENODEV;
> > + }
> > +
> > + fwspec.fwnode = of_node_to_fwnode(irq_parent);
> > + fwspec.param_count = 3;
> > + for (i = 0; i < pru->evt_count; i++) {
> > + fwspec.param[0] = rsc->pru_intc_map[i].event;
> > + fwspec.param[1] = rsc->pru_intc_map[i].chnl;
> > + fwspec.param[2] = rsc->pru_intc_map[i].host;
> > +
> > + dev_dbg(dev, "mapping%d: event %d, chnl %d, host %d\n",
> > + i, fwspec.param[0], fwspec.param[1], fwspec.param[2]);
> > +
> > + pru->mapped_irq[i] = irq_create_fwspec_mapping(&fwspec);
> > + if (pru->mapped_irq[i] < 0) {
>
> Function irq_create_fwspec_mapping() returns an unsigned int - theoretically the
> above check could return a false positive. I suggest to make
> pru_proc::mapped_irq a '*unsigned int" and revise the error condition.
You are right - I will do as suggested.
>
> > + dev_err(dev, "failed to get virq\n");
> > + ret = pru->mapped_irq[i];
> > + goto map_fail;
> > + }
> > + }
> > +
> > + return ret;
> > +
> > +map_fail:
> > + pru_dispose_irq_mapping(pru);
> > +
> > + return ret;
> > +}
> > +
> > static int pru_rproc_start(struct rproc *rproc)
> > {
> > struct device *dev = &rproc->dev;
> > struct pru_rproc *pru = rproc->priv;
> > u32 val;
> > + int ret;
> >
> > dev_dbg(dev, "starting PRU%d: entry-point = 0x%llx\n",
> > pru->id, (rproc->bootaddr >> 2));
> >
> > + ret = pru_handle_intrmap(rproc);
> > + /*
> > + * reset references to pru interrupt map - they will stop being valid
> > + * after rproc_start returns
> > + */
>
> Why is that? As far as I understand the interrupt map points inside the
> firmware image, which won't go away until @rproc is disposed of or users change
> it via sysfs. And the latter can't happen when the remote processor is active.
> Can't this go to pru_dispose_irq_mapping()?
Those references are pointing to the fw segments which are released
right after rproc_start() due to release_firmware() call. I think that
resetting them before pru_rproc_start() returns is proper. If you
don't mind I prefer to keep this part as is.
Thank you,
Grzegorz
>
> More comments to come tomorrow.
>
> Thanks,
> Mathieu
>
> > + pru->pru_interrupt_map = NULL;
> > + pru->pru_interrupt_map_sz = 0;
> > + if (ret)
> > + return ret;
> > +
> > val = CTRL_CTRL_EN | ((rproc->bootaddr >> 2) << 16);
> > pru_control_write_reg(pru, PRU_CTRL_CTRL, val);
> >
> > @@ -113,6 +218,10 @@ static int pru_rproc_stop(struct rproc *rproc)
> > val &= ~CTRL_CTRL_EN;
> > pru_control_write_reg(pru, PRU_CTRL_CTRL, val);
> >
> > + /* dispose irq mapping - new firmware can provide new mapping */
> > + if (pru->mapped_irq)
> > + pru_dispose_irq_mapping(pru);
> > +
> > return 0;
> > }
> >
> > @@ -275,12 +384,70 @@ pru_rproc_load_elf_segments(struct rproc *rproc, const struct firmware *fw)
> > return ret;
> > }
> >
> > +static const void *
> > +pru_rproc_find_interrupt_map(struct device *dev, const struct firmware *fw)
> > +{
> > + struct elf32_shdr *shdr, *name_table_shdr;
> > + const char *name_table;
> > + const u8 *elf_data = fw->data;
> > + struct elf32_hdr *ehdr = (struct elf32_hdr *)elf_data;
> > + u16 shnum = ehdr->e_shnum;
> > + u16 shstrndx = ehdr->e_shstrndx;
> > + int i;
> > +
> > + /* first, get the section header */
> > + shdr = (struct elf32_shdr *)(elf_data + ehdr->e_shoff);
> > + /* compute name table section header entry in shdr array */
> > + name_table_shdr = shdr + shstrndx;
> > + /* finally, compute the name table section address in elf */
> > + name_table = elf_data + name_table_shdr->sh_offset;
> > +
> > + for (i = 0; i < shnum; i++, shdr++) {
> > + u32 size = shdr->sh_size;
> > + u32 offset = shdr->sh_offset;
> > + u32 name = shdr->sh_name;
> > +
> > + if (strcmp(name_table + name, ".pru_irq_map"))
> > + continue;
> > +
> > + /* make sure we have the entire irq map */
> > + if (offset + size > fw->size || offset + size < size) {
> > + dev_err(dev, ".pru_irq_map section truncated\n");
> > + return ERR_PTR(-EINVAL);
> > + }
> > +
> > + /* make sure irq map has at least the header */
> > + if (sizeof(struct pru_irq_rsc) > size) {
> > + dev_err(dev, "header-less .pru_irq_map section\n");
> > + return ERR_PTR(-EINVAL);
> > + }
> > +
> > + return shdr;
> > + }
> > +
> > + dev_dbg(dev, "no .pru_irq_map section found for this fw\n");
> > +
> > + return NULL;
> > +}
> > +
> > /*
> > * Use a custom parse_fw callback function for dealing with PRU firmware
> > * specific sections.
> > + *
> > + * The firmware blob can contain optional ELF sections: .resource_table section
> > + * and .pru_irq_map one. The second one contains the PRUSS interrupt mapping
> > + * description, which needs to be setup before powering on the PRU core. To
> > + * avoid RAM wastage this ELF section is not mapped to any ELF segment (by the
> > + * firmware linker) and therefore is not loaded to PRU memory.
> > */
> > static int pru_rproc_parse_fw(struct rproc *rproc, const struct firmware *fw)
> > {
> > + struct device *dev = &rproc->dev;
> > + struct pru_rproc *pru = rproc->priv;
> > + const u8 *elf_data = fw->data;
> > + const void *shdr;
> > + u8 class = fw_elf_get_class(fw);
> > + u64 sh_offset;
> > int ret;
> >
> > /* load optional rsc table */
> > @@ -290,6 +457,19 @@ static int pru_rproc_parse_fw(struct rproc *rproc, const struct firmware *fw)
> > else if (ret)
> > return ret;
> >
> > + /* find .pru_interrupt_map section, not having it is not an error */
> > + shdr = pru_rproc_find_interrupt_map(dev, fw);
> > + if (IS_ERR(shdr))
> > + return PTR_ERR(shdr);
> > +
> > + if (!shdr)
> > + return 0;
> > +
> > + /* preserve pointer to PRU interrupt map together with it size */
> > + sh_offset = elf_shdr_get_sh_offset(class, shdr);
> > + pru->pru_interrupt_map = (struct pru_irq_rsc *)(elf_data + sh_offset);
> > + pru->pru_interrupt_map_sz = elf_shdr_get_sh_size(class, shdr);
> > +
> > return 0;
> > }
> >
> > diff --git a/drivers/remoteproc/pru_rproc.h b/drivers/remoteproc/pru_rproc.h
> > new file mode 100644
> > index 000000000000..8ee9c3171610
> > --- /dev/null
> > +++ b/drivers/remoteproc/pru_rproc.h
> > @@ -0,0 +1,46 @@
> > +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) */
> > +/*
> > + * PRUSS Remote Processor specific types
> > + *
> > + * Copyright (C) 2014-2020 Texas Instruments Incorporated - https://www.ti.com/
> > + * Suman Anna <s-anna@xxxxxx>
> > + */
> > +
> > +#ifndef _PRU_RPROC_H_
> > +#define _PRU_RPROC_H_
> > +
> > +/**
> > + * struct pruss_int_map - PRU system events _to_ channel and host mapping
> > + * @event: number of the system event
> > + * @chnl: channel number assigned to a given @event
> > + * @host: host number assigned to a given @chnl
> > + *
> > + * PRU system events are mapped to channels, and these channels are mapped
> > + * to host interrupts. Events can be mapped to channels in a one-to-one or
> > + * many-to-one ratio (multiple events per channel), and channels can be
> > + * mapped to host interrupts in a one-to-one or many-to-one ratio (multiple
> > + * channels per interrupt).
> > + */
> > +struct pruss_int_map {
> > + u8 event;
> > + u8 chnl;
> > + u8 host;
> > +};
> > +
> > +/**
> > + * struct pru_irq_rsc - PRU firmware section header for IRQ data
> > + * @type: resource type
> > + * @num_evts: number of described events
> > + * @pru_intc_map: PRU interrupt routing description
> > + *
> > + * The PRU firmware blob can contain optional .pru_irq_map ELF section, which
> > + * provides the PRUSS interrupt mapping description. The pru_irq_rsc struct
> > + * describes resource entry format.
> > + */
> > +struct pru_irq_rsc {
> > + u8 type;
> > + u8 num_evts;
> > + struct pruss_int_map pru_intc_map[];
> > +} __packed;
> > +
> > +#endif /* _PRU_RPROC_H_ */
> > --
> > 2.29.0
> >
